Digi PortServer TS 16 MEI基本配置

F2X16系列IP MODEM使用说明书文档版本密级V2.0.0产品名称：F2X16共31页F2X16系列IP MODEM使用说明书此说明书适用于下列型号产品：型号产品类别F2116GPRS IP MODEMF2216CDMA IP MODEMF2416WCDMA IP MODEMF2616EVDOIP MODEMF2716TDD-LTE IP MODEMF2816FDD-LTE IP MODEMF2A16LTE IP MODEMF2C16Cat.1IP MODEM厦门四信通信科技有限公司Add：厦门市集美区软件园三期诚毅大街370号A06栋11层客户热线：400-8838-199电话：+86-592-6300320传真：+86-592-5912735网址文档修订记录日期版本说明作者2016-04-03V1.0.0初建wzj 2016-10-09V1.0.1重新调整文档格式zxzzxz 2017-01-09V1.0.21修改波特率说明2增加网络制式选择2017-05-05V1.0.3删除相关功能描述zxz 2017-09-23V2.0.0更新地址Faine 2020-5-20V2.0.1增加F2C16系列ZCL著作权声明本文档所载的所有材料或内容受版权法的保护，所有版权由厦门四信通信科技有限公司拥有，但注明引用其他方的内容除外。

未经四信公司书面许可，任何人不得将本文档上的任何内容以任何方式进行复制、经销、翻印、连接、传送等任何商业目的的使用，但对于非商业目的的、个人使用的下载或打印（条件是不得修改，且须保留该材料中的版权说明或其他所有权的说明）除外。

商标声明Four-Faith 、四信、、、均系厦门四信通信科技有限公司注册商标，未经事先书面许可，任何人不得以任何方式使用四信名称及四信的商标、标记。

注：不同型号配件和接口可能存在差异，具体以实物为准。

目录第一章产品简介 (6)1.1产品概述 (6)1.3工作原理框图 (7)1.4产品规格 (8)第二章安装 (11)2.1概述 (11)2.2开箱 (11)2.3安装与电缆连接 (11)2.4电源说明 (14)2.5指示灯说明 (14)第三章参数配置 (15)3.1配置连接 (15)3.2参数配置方式介绍 (15)3.3参数配置详细说明 (15)3.3.1配置工具运行界面 (16)3.3.2设备上电 (17)3.3.4中心服务 (23)3.3.5串口 (24)3.3.6无线拔号 (25)3.3.7全局参数 (26)3.3.8设备管理 (27)3.3.9其它功能项 (28)第四章数据传输试验环境测试 (29)4.1试验环境网络结构 (29)4.2测试步骤 (29)第一章产品简介1.1产品概述F2X16系列IP MODEM 是一种物联网无线数据终端，利用公用蜂窝网络为用户提供无线长距离数据传输功能。

MODEL 1600系列终端服务器使用说明Hutone Portserver目录第1章 概 述1.1 前言 (2)1.2 产品介绍 (2)1.3 产品特点 (2)1.3.1 性能参数 (2)1.3.2 接口说明 (2)第2章 安 装2.1 硬件安装 (3)2.2 软件安装 (3)2.2.1 windows 系统的软件安装 (3)2.2.2 unix 系统的软件安装 (5)第3章 登陆及配置3.1 windows 系统登陆及配置 (6)3.1.1 telnet 方式 (6)3.1.2 web 方式 (11)3.2 unix 系统登陆及配置 (16)第4章 应 用4.1 COM口模式 (17)4.2 TTY模式 (18)4.3 SCK模式 (20)4.4 PPP模式 (23)4.5 LPD模式 (25)附1关于MODEL1600系列终端服务器的线序说明 (32)附2 RJ45网头与DB9或DB25针和孔的关系 (34)1.1 前言欢迎使用本公司MODEL1600系列终端服务器以前，有很多设备需要我们亲临现场去操作，去监控，并且这些设备可能由不同的操作系统去控制，也许每台设备需要一台价格昂贵的PC来支持。

现在，以太网—互联网等网络构架已逐渐在自动化产业内被之广泛应用，串口通信成为自动化系统通信的主流。

通过TCP/IP和以太网，利用终端服务器可以使原本不具备网口的设备立即连接到网络中，供您随时操作，同时使这些设备能够利用不同的主机资源，为您节省大量的成本，让您尽享网络的无比优越。

1.2 产品简介终端服务器采用高性能的专用处理器，和全智能的嵌入式操作系统。

可将RS232串口的数据转换成TCP/IP、ARP、PPP、TELNET、UDP等协议平台上的10M/100M以太网数据。

可以把MODEL1600系列的终端服务器通过以太网连接在Unix/linux主机上，通过以太网使用TCP/IP提供TTY服务的终端服务器。

1.终端服务器PortServer TS16的端口设置检查1.1 电脑和终端的关系图电脑和终端服务器一起接到交换机上面，电脑就可以通过交换机访问终端，就可以对终端进行相应的设置以及检测。

2.1 终端ip的搜索用户名：root，密码：dbps。

把终端和电脑连接到同一个交换机，然后再电脑上测终端端口的好坏：使用Digi软件安装包，打开setup.exe出现：点击下一步，可以看到终端的ip地址：2.2 登陆IE浏览器（1）在IE浏览器中输入ip地址，登陆出现提示输入口令，输入后出现界面，然后点击Network，使用以下ip地址：（2）点击进入Serial Ports，Port 1，Change Profile，钩上Tcp server，Tcp client，点击Apply 点击第一个Port 1，点击Base Socket进入，在点Advanced Network Settings，然后把Base Socke t改为3900，这个是为了让端口生成端口号。

（3）回到port 1界面，点击进入Basic Serial Settings，设置波特率为1200：（4）然后回到Serial Ports，点copy把2~16点上，APPLY,后面的端口就会安装端口一的配置而配置。

2.3端口测试（1）打开TCP/UDP Socket 调试工具V2.3，点击TCP Client，后点创建，在弹出的窗口里面输入终端的ip地址和对应的端口号。

将网线插入所测试的端口，把网线的4、5线短接（因为4、5线是收发端，这里可以查看终端的说明）这样就可以开始测试了。

打开刚刚新建的对应端口，点连接后，端口正常的话能连接上，会提示已连接，不正常的话重启终端看看，再试一次，然后输入数据发送，正常会看得到数据接收返回。

（2）遇到问题：刚测试第一个端口就没能连上，就卡在那里不会了！！应该转变思维去测试第二端口的，举一反三，这也是新手容易配到的一些问题，解决问题时候，刚刚就遇到第一个有问题，结果卡住浪费时间，所以要多思维转变。

Digi PortServer TS 16 MEI基本配置采用DPA-Remote工具和浏览器进行配置：按“Discover”键，设备发现窗口中会显示出在本网段的所有的Digi产品。

给发现的设备分配IP地址（出厂时DHCP=ON)。

、双击新发现的地址为0.0.0.0的设备，输入IP地址和相应的网络配置。

如网上有DHCP服务器，TS将会自动获得一个IP地址。

（注意：初始化设备，必须进入设备配置界面，关闭DHCP，确认固定IP地址输入正确，再重新启动后，IP地址才能正式生效。

）运行DPA RemoteDPA-remote软件将自动搜索本网段所有DIGI设备在网段中不要有DHCP SERVER否则设备将自动获取一个IP 地址，如第10页配置IP地址IP地址为0.0.0.0的条目，然后在分配地址的新窗口输入分配的地址信息。

程序会分发地址并刷新确认。

如设备已获得IP地址，将如上显示如果设备IP为DHCP自动分配，可通过MAC 地址确定你所需要的设备选择你需要的设备条目，再点击configure进入设备管理界面。

管理员认证输入用户名和密码，出厂值是用户名：root,密码是：dbpsDIGI PortServer TS 16 MEI的WEB配置界面确认或配置你所需要的IP 地址等确认或输入IP地址参数配置完选择Apply,设备将重新启动保存IP配置选择Serial Ports会出现设备所有端口的信息选择你需要配置的端口点击Copy可以复制该端口的配置信息到其他端口请选择TCP Sockets 类型，然后Apply，进入下一页端口的TCP Sockets设置端口将工作在TCP Server模式下，Socket端口地址号是200X或210X，其中的是端口号。

根据所连设备的串口参数配置终端服务器串口端口参数设置如采用8 PIN RJ-45接头，请在Advanced Serial如采用422/485，在MEI Serial Settings配置端口参数恢复出厂值配置好装置后连上设备注意接线方式，然后根据配置连通装置。

Digi Connect® WAN Application GuideUsing the Serial Console Port forOut-of-Band Console Management of Remote DevicesScenarioA Digi Connect WAN is used for primary or backup remote site WAN connectivity over a cellular wireless network. The Digi Connect WAN features a console port which may be used to interface to a serial port on a remote router, VPN appliance, firewall or other network equipment, providing secure out-of-band console management access. Administrators who require reliable communications to remote assets can rely on the Digi Connect WAN to provide an alternative to wired landline connections for a truly diverse TCP/IP network connection. Benefits include secure connection; network diversity; network backup to remote site; cost-effective communications (can be less expensive than POTS modem connection); and easy access from anywhere to remote devices. Theory of OperationIn a typical Digi Connect WAN application, a remote router plugs into an Ethernet port on the Digi Connect WAN via an Ethernet WAN port on the router. This provides a wireless WAN connection over a cellular IP network. For more information on this application, please refer to the Digi Connect WAN application guides for primary or fail-over WAN IP routing.A side benefit of the Digi Connect WAN is its ability to interface to remote serial devices via its RS-232 console port. The console port by default performs the same function as a router’s console port (i.e., to provide direct access to the device’s command line) for full administration, configuration, troubleshooting and control of the device. However, with a serial cable and a few clicks of the mouse, the console port on the Digi Connect WAN becomes a secure, persistent out-of-band connection to a router or other appliance’s console port using SSH or telnet.Console Message Logging: Logging of console messages generated from the attached network device’s console port is also supported. By default, 32kb of messages are stored in a FIFO queue and can be viewed using the “display buffer’s” CLI command or from the WebUI via the Management > Ports function.TCP Ports: The Digi Connect WAN, like most terminal servers, uses special TCP port numbers (in this case 2001 and 2501 for telnet and SSH respectively) to tell the Digi Connect WAN to pass telnet or SSH traffic through to a serial port.Direct command line access to the Digi Connect WAN itself is still available by using standard telnet or SSH TCP port numbers (ports 23 and 22 by default).In all cases, the TCP ports used for both pass-through and direct SSH/telnet access can be changed via the WebUI or CLI.Sample Application DiagramRemote Site HQTelnet orThe above diagram shows how multiple telnet or SSH clients can access the remote router/VPN appliance via the Digi Connect WAN using a wireless GSM or CDMA cellular network.Digi Connect WAN Configuration1.Read and follow the quick-start guide for the Digi Connect WAN and, optionally, theapplicable Digi Connect WAN application guides.2.Connect a serial console (a.k.a. null modem or crossover – not straight-thru) cablefrom the DB-9M console port on the Digi Connect WAN to the network device’s console port.3.Configure the serial Port 1 on the Digi Connect WAN for Console Management:a.Open a browser and point to the IP address of the Digi Connect WAN.b.In the WebUI select Configuration > Serial Port > Port 1c.Select “Change Profile”, choose “Console Management”, press “Apply”. Ascreen similar to the one below will appear:4.Serial port parameters: The default settings are 9600, 8, 1, N, no flow control. Tochange or verify these settings select “Basic Settings” in the serial port configuration.5.The TCP ports used by telnet and SSH can be changed: The default TCP ports areService Default TCP PortTelnet 2001SSH 2501These can be changed or disabled as shown above.6.Port logging stores console messages for later viewing via the Management > SerialPorts screen. This feature can be disabled. The buffer size can be changed.7.IP filtering and TCP/UDP port service settings provide firewall-like capabilities to theDigi Connect WAN. Improper settings may block telnet or SSH traffic.Sample Session: Refer to the diagram above using this IP address:Digi Connect WAN wireless link 10.25.13.5Access Network Device’s Console Port Through the Digi Connect WAN: Telnet to10.25.13.5 port 2001 – this will connect directly to the network device’s console port (e.g., from Windows command line enter “telnet 10.25.13.5 2001”).SSH to 10.25.13.5 port 2501 – SSH requires login to the Digi Connect WAN first using a user name (root is the default and must be entered even if login isdisabled) and optional password and then connect to the device’s console port. More ports and advanced features, such as power management, are available via the Digi CM™ and Digi PortServer® TS products. Port forwarding entries on the Digi Connect WAN are used to pass the incoming telnet/SSH traffic thorough the Digi Connect WAN to the terminal server.For example, a PortServer TS 4 connected to the Ethernet port of the Digi Connect WAN is assigned IP address 192.168.1.3. To access serial Port 3 of the PortServer TS 4, create a TCP port forwarding entry on the Digi Connect WAN to forward TCP Port 2003 (the default TCP port for Port 3) to IP address 192.168.1.3.Where to Get More InformationRefer to the Digi Connect WAN user documentation and Digi technical support website at /support for more information. Technical assistance is available at /support/eservice/eservicelogin.jsp.For sales information, please contact Digi International at 952-912-3444.。

TS16的端口参数设定步骤
此操作请在不影响数据观测和航班起降时进行。

本机场只对TS16的Port1~Port8八个端口的此参数进行修改，其它参数设定请勿修改
1. 打开IE浏览器，输入19
2.168.1.101 (TS16的IP地址) 访问TS16的配置界面。

进入界面后，点击左侧红框所示的Serial Ports选项。

2. 点击Serial Ports选项后，界面显示如下图。

点击红框所示的Port1的选项。

3.点击Port1的选项后，界面显示如下图，进入Port1 (1号端口) 的参数设定界面。

拖动界面右侧红框指示的滚动条至最底端。

4. 界面显示如下，点击红框所示的MEI Serial Settings选项。

5. 界面进入MEI Serial Settings选项。

此时显示本机场当前的参数设定为红框所示的选项，如下图。

6. 修改此参数，点击选择Terminated选项，如下图红框所示。

参数修改完成点击下方的Apply 按钮，对新修改的参数进行保存并生效。

此时界面上方显示Changes have been saved successfully 如红框所示，表示参数修改成功。

7. 点击界面左侧Serial Ports选项
返回如下图所示界面，进行Port2 (2号端口)的设定。

设定步骤如Port1的设定
8.按照上述操作步骤，对Port1~Port8的此参数进行修改。

Quick Start Guide*If switch 4 is up, termination resistor If switch 4 is down, termination resistorCongratulations!Configuration is complete.Go to the User's Guide on the CD for moreinformation.deviceConnect Ethernet cableInsert CDFollow wizard© Digi International Inc., 2006.Digi, Digi International, the Digi logo, and PortServer TS are trademarks or registered trademarks of Digi International, Inc. in the United States and other countries worldwide.All other trademarks are the property of their respective owners.PortServer TS 1 MEI (shown)PortServer TS 16 MEI (shown)Connect Connect serialConnect Ethernet cablePortServer TS MEI PortServer TS P MEI PortServer TS H MEIPortServer TS What you will needPortServer TS 8PortServer TS 16 MEIConnect serial devices2124Be sure to check Digi Support for the latest firmware updates at:LEDs will flash during startup*You must disablefirewall/antivirus software before running wizard.!(PortServer TS families 1/2/4/8only)PN:(1P)B90000687-88Accessing the CD from a UNIX SystemInsert CD in system CD driveAll RJ-45 cables and connectors are 8-pin. When using these adapters with modems or other applications that require DCD on pin 1, you must turn on altpin. If altpin is turned off, the hardware signal on pin 1 becomes DSR instead of DCD. This alternative can be used if DCD is not required, and DSR is needed instead. Configure the altpin through the web interface or the command line. See the User's Guide, MEI chapter or the set flow command in the Command Reference on the Digi CD under Documentation for more information about setting the altpin.Cabling your serial devices to aDigi Product is now simpler than ever with a Digi Cable Adapter. While manycustom cabling solutions can leave youwith a cable that is either too long or tooshort for your application, the Digi Cable Adapters are used with commercially available CAT 5 cable of any length. Simply plug standard CAT 5cable into your Digi Product, connect aCable Adapter to the other end and plugthe adapter into your device. Whetheryou need a crossover or straight-throughconnection, or require a DB-9 orDB-25 connector, there is aDigi Cable Adapter solution.For additional cabling information, see the Cabling guide under Documentation on your CD. If you prefer to order cables, see our website at and select Cabling.Digi TS EIA-232 Cable Adapter ReferenceBay Accelar, Nortel and other DB-9 DTE devices Sun Sparc, Sun Ultra, terminals, printers and other DTE devices with DB-25 Female portsCisco, IBM and other DTE devices with DB-25 Male ports Modems and other DCE devices with DB-25 Female Ports Modems and other DCE devices with DB-9 Female PortsFor use with Printers. This adapter differs from a Console Adapter in that it utilizes the DTR signal (instead of RTS) for hardware flow control For use with Cisco and Sun RJ-45 Console ports. Also available in 8-pack and 16-pack quantities.Can be used as a networking cable or combined withone of the adapters as a serial cable.76000697 Digi TS DB-9FConsole Adapter (4-pack)76000698 Digi TS DB-25MConsole Adapter (4-pack)76000699 Digi TS DB-25F Console Adapter (4-pack)76000700 Digi TS DB-25MModem Adapter (4-pack)76000701 Digi TS DB-9M Modem Adapter (4-pack)76000692 Digi TS DB-25M Printer Adapter (4-pack) 76000631 Digi TS to Sun Netra / Cisco Cable (single pack)63000042-01 RJ-45 to RJ-45Straight Through Ethernet Cable Part numberApplicationAdapterNeed help with cabling?。

MB16AWP无线便携式显示器用户指南第一版2022 年 1 月版权所有 © 2022 ASUSTeK COMPUTER INC. 保留所有权利。

未经 ASUSTeK COMPUTER INC. ("ASUS") 明确书面同意，不得以任何形式或通过任何方式复制、传播、转录本手册的任何部分，包括其中介绍的产品和软件，也不得存储到检索系统中或翻译成任何语言，购买者出于备份目的而保留的文档除外。

在下列情况下，不能享受产品保修或维修服务：(1) 产品被修理、修改或改动，除非此类修理、修改或改动得到 ASUS 的书面授权；(2) 产品序列号损毁或缺失。

ASUS“按原样”提供本手册，不提供任何明示或隐含的担保，包括但不限于对于适销性或针对特定目的的适用性的隐含担保或条件。

无论在任何情况下，ASUS 及其董事成员、高级职员、员工或代理不对由于本手册或产品中存在任何缺陷或错误而导致的任何间接、特殊、偶然或必然损失（包括收益损失、业务损失、不能使用或数据丢失、业务中断等）承担任何责任，即使 ASUS 已被告知此类损失的可能性。

本手册中包含的规格和信息仅供一般性参考，可能会随时变更而无需另行通知，因此不应构成 ASUS 的承诺。

ASUS 对本手册（包括其中介绍的产品和软件）中可能存在的任何错误不承担任何责任。

本手册中出现的产品名称和公司名称可能分别是或不是相应公司的注册商标或版权，仅用于标示或解释目的，无意侵犯其所有者的权益。

ii目录 (iii)声明 (iv)安全信息 (xi)保养和清洁 (xii)中国产品回收服务 (xiii)北美可充电电池回收服务 (xiii)产品欧盟能源标识信息 (xiii)第 1 章：产品介绍1.1 欢迎使用！ .....................................................................................1-11.2 物品清单.........................................................................................1-11.3 显示器简介 .....................................................................................1-21.3.1 前部概览/侧面概览 ........................................................1-2第 2 章：设置2.1 显示器竖立位置 ..............................................................................2-12.2 调整显示器 .....................................................................................2-12.3 连接线缆.........................................................................................2-22.4 打开显示器电源 ..............................................................................2-22.5 执行无线投影..................................................................................2-32.6 将显示器连接到 Internet ................................................................2-42.7 更新无线投影固件 ..........................................................................2-52.8 通知 ................................................................................................2-6第 3 章：一般说明3.1 OSD（屏幕显示）菜单...................................................................3-13.1.1 如何重新配置 ..................................................................3-13.1.2 OSD功能介绍.................................................................3-23.2 规格摘要.........................................................................................3-93.3 外形尺寸.......................................................................................3-113.4 故障排除（常见问题） .................................................................3-123.5 支持的运行模式 ............................................................................3-13iii联邦通信委员会声明本设备符合 FCC 规则第 15 部分的要求。

三汇DST系列录音卡SHR-16DA-CT/PCI数字电话录音卡Version 2.0杭州三汇信息工程有限公司目录目录 (i)版权申明 (ii)版本修订记录 (iii)第1章概述 (1)1.1 功能描述 (1)1.2 性能特点 (1)1.3 板卡工作原理框图 (4)1.4 功能模块 (4)第2章安装 (5)2.1结构示意图 (5)2.2系统要求 (7)2.3安装步骤 (7)附录A 主要技术/性能参数 (10)附录B 技术/销售支持 (11)版权申明本文档版权属杭州三汇信息工程有限公司所有。

杭州三汇信息工程有限公司保留对此文件进行修改而不另行通知之权利。

杭州三汇信息工程有限公司承诺所提供的信息为正确且可靠, 但并不保证本文件绝无错误。

请在使用本产品前, 自行确定所使用的相关技术文件及规格为最新有效之版本。

若因贵公司使用本公司之文件或产品, 而需要第三方之产品、专利或者著作等与其配合时，则应由贵公司负责取得第三方同意及授权。

关于上述同意及授权，非属本公司应为保证之责任。

版本修订记录版本号发布日期修订内容Version1.0 2005.3 新创建此文档。

Version2.0 2006.8 增加了板卡和模块的图形说明，并纠正一些不规范的说明。

请访问我们的网站（）以获取该文档的最新版本。

第1章 概述DST系列SHR-16DA-CT/PCI型数字电话录音卡，是一种采用PCI总线的16通道数字线录音卡，该录音卡专用于数字电话用户线（分机线）的并线录音。

1.1 功能描述z数字电话线高阻并线录音z多种方式实现录音停止/启动z支持16通道同时录音, 不同的通道可以同时进行不同格式的录音z支持每个通道上行、下行单向录音或上下行混合录音z支持接收主被叫号码z同步获取录音过程中的话机显示内容z用户话机按键接收z通话/静音检测z录音操作支持自动增益控制（AGC）z呼叫进程监控z自动检测主板上是否安装了业务模块和数量z支持录音卡或数字电话机断线故障检测1.2 性能特点z支持PCI2.1总线符合PCI2.1总线标准，突发数据传送速率高达133 MB/s；支持即插即用（PNP），无需任何跳线设置。

Configuring DMS Central Control Software to Communicate with VMS Signs Using the PortServer ® TS H MEI Serial ServerIntroductionThis technical document provides instructions for configuring Skyline Products, Inc.’s DMS Central Control software to communicate with a sign’s configured PortServer TS H MEI device (formerly called Digi One ® TS). The instructions are intended for experienced techniciansinstalling the PortServer TS H MEI device server to communicate with Skyline Variable Message Signs (VMS) using a Safetran 170E controller that includes a 470IB Prom module.If you are not sure what this document describes, or if you have questions, please contact Skyline Customer Service at 719-392-9046, Option # 5.PortServer TS H MEI is a product of Digi International ®.Disclaimer of Endorsement: Reference herein to any specific commercial products, process, or service by trade name, trademark, manufacturer, or otherwise, does not necessarily constitute or imply its endorsement, recommendation, or favoring by Skyline Products, Inc. The views and opinions of authors expressed herein do not necessarily state or reflect those of the Skyline Products, Inc, and shall not be used for advertising or product endorsement purposes.Disclaimer of Liability: With respect to this document, neither Skyline Products, Inc. nor any of Skyline’s employees, makes any warranty, express or implied, including the warranties of merchantability and fitness for a particular purpose, or assumes any legal liability or responsibility for the accuracy, completeness, or usefulness of any information, apparatus, product, or process disclosed, or represents that its use would not infringe privately owned rights.Application NotePortServer TS H MEI Digi International The PortServer TS H MEI serial server is used for universal, high-performance serial-to-Ethernet connectivity. It is designed for use in remote applications to withstand more extreme temperatures (-35° C to +74° C).Configuring DMS Central ControlImportant: Before configuring the Skyline DMS Central Control software to communicate with the PortServer TS H MEI device, be certain that DMS Central can communicate with the sign. One method of verification is to connect a laptop running DMS Central, configured to communicate directly with the sign, to the local port in the sign and test the sign polling. Once you know the sign is working with a known good configuration, continue with the following step.Updating the DMSServer.ini FileAdd the following lines to the Config section of the DmsServer.ini file:[Config]ForceDestinationPort=falseDestinationPort=2101Creating a Communication Pool1. In the Skyline DMS Central Control, select Admin>>Comms. The Communication Settingsdialog box appears.2. Click Add. The Comm Pool dialog box appears.3. In the Comm Pool Name text box, type a descriptive name. For example, Ethernet-Serial.4. In the Protocol Stack>>Name text box, select Ethernet to Serial.5. Click OK. Ethernet-Serial is added to the Communication Pools list.6. In the Available Ports Define text box, type 2101 and then click Define. The port is added to theAvailable Ports list.7. In the Available Ports list, double-click the 2101 port. The port is added to the Assigned Portslist. Double-click any other port numbers in the Assigned Ports list to move them to the Available Ports list. 2101 should be the only port in the Assigned Ports list.8. Click Done.Configuring Sign Communications1. In DMS Central Control, highlight a sign and then select Signs>>Configure Sign. The SignConfiguration dialog box appears.2. Select the Communications tab.3. In the Comm Pool drop-down list, select the communication pool you created. For example,Ethernet-Serial.4. In the IP Address text box, type the sign’s PortServer device’s static IP address.5. Click Save/Download. The Save/Download Configuration dialog box appears.6. Select Basic Configuration and then click OK. The Comm Pool and IP address changes aredownloaded to the sign.Configuring the PortServer TS H MEI Device to Communicate with the VMS SignUse the following steps to configure the PortServer TS H MEI device so that DMS Central Control software can use the device to communicate with the sign.Setting the Digi Network Configuration1. Open a Web browser and type http://xxx.xxx.xxx.xxx (IP address of the Digi device) as the URLaddress to open the PortServer Configuration and Management window.2. To set the Static IP of the Digi PortServer TS device, select Network in the left hand menu. TheNetwork Configuration work area appears.3. In the IP Settings area, select Use the following IP address.4. In the IP Address text box, type the sign’s PortServer TS H MEI device’s static IP address. Thisaddress should match the address used in the Skyline DMS Central SignConfiguration>>Communications Tab.5. In the Subnet Mask text box, type the subnet mask used on your network.6. In the Default Gateway text box, type the gateway address used by your network.7. Click Apply.Setting the Port Profile1. In the left hand menu, select Serial Port. The Select Port Profile work area appears.2. Select UDP Sockets and then select Apply. The Port Profile configuration area appears.3. In the UDP Client − Send data to table, type an informative description in the text box.4. In the Send To text box, type the DMS Central Control server’s static IP address.5. In the UDP Port text box, type 2101.6. Click Add.7. Select the Send data after the following number of idle milliseconds check box and then type25 in the ms text box. You may need to change this value if using modems, the value may need tobe increased or decreased to optimize communications.8. Click Apply.9. Close PortServer Configuration and Management browser window.Verifying Communications between the VMS Sign and the Digi Device Poll the sign using Skyline DMS Central software to verify sign communications. See Skyline DMS Central Control User’s Guide.Note:These instructions are for the PortServer TS H MEI; however, the information may be used as a general guideline for use with other Digi devices using similar configuration.。

PortServer TS 16Setup CardAbout This CardThis card provides the following information on your PortServer TS 16:• A brief introduction• A setup overview that identifies the major steps required fordevice setup•Guidance on where to find more detailed information thatmay be required to complete setup and administrative tasksKey FeaturesThe following are some of the key features of PortServer TS 16:Console ManagementPortServer TS 16 provides the following console management features:•Secure access to remote systems using SSHv2•“Solaris Ready” certification from Sun Microsystems•Inbound and outbound PPP connections for remote access tonetwork equipment•Port buffering of up to 64 KB per port to diagnose networkproblems Terminal ServerPortServer TS 16 provides the following terminal server features:•Serial ports capable of supporting asynchronous, high-speedconnections to printers, modems, terminals, and otherdevices. Support extends to full modem control and hardware handshaking.•Local TTY and COM port functionality using Digi RealPortsoftware GeneralPortServer TS 16 provides the following general features:•Auto-sensing 10/100 TX Ethernet connection•Industry standard surge suppression and ESD protection to 15kilovolts on all signal pins•LED indicators to display network information•Local configuration using a terminal or PC and remote con-figuration using either a Telnet connection or a web browser •Remote monitoring and IP address configuration using DigiPort Authority - Remote•Upgradable firmware using TFTP or HTTPPackage ContentsThe package contains the following items:•One PortServer TS 16 with an integrated power supply•One RJ-45-to-DB-25 crossover cable and one RJ45-to-DB9crossover cableNote: These are intended for connecting a terminal or PC so that you can configure your PortServer TS 16 using the com-mand line interface.•One Sun Netra crossover cable to connect to SUN Netra serv-ers and Cisco routers and switches (Rack Mount units only)Note: For additional cables, contact your dealer or distributor.•Optional Rack Mount Kit (19” and 23”)•One loopback plug •Access Resource CD•This card, an Access Resource CD card, and associatedpaperworkSetup OverviewThis overview identifies the major steps required to set up your PortServer TS 16. It provides simple methods for accomplishing common setup tasks. For information on alternative methods, see the online documentation. Step A: Set Up the Hardware1.Connect the PortServer TS 16 to a proper power source andthe PortServer TS 16 to the network. See the Specifications table on the backside of this document for details.2.Connect peripherals to serial ports. See the Terminal ServerCable Guide for information on cabling peripherals to serial ports. Step B: Install and Set Up DPA-RemoteThis step is not required if you do not intend to use DPA-Remote to configure the IP address or to monitor ports.Notes: (1) DPA-Remote cannot be used to change the IP address of a PortServer TS 16 that has already been assigned one; it can only be used to configure the initial IP address. (2) DPA remote cannot assign an IP address on a network that has an active DHCP server.For information on installing DPA-Remote, see the online Digi Port Authority - Remote Device Monitor Setup Guide . Step C: Configure an IP AddressThe following are 4 methods for configuring an IP address. Use the one that is most convenient for you.Method 1: Using DP A-Remote 1.Run DPA-Remote.2.If DPA-Remote is not set for ADDP, choose ADDP as theDiscovery Protocol.3.Choose Discover. A list of Digi devices with IP addresses of0.0.0.0 appears.4.Select a PortServer TS 16 from the list and then choose Con-figure.5.Supply an IP address, subnet mask, and default gateway andthen choose OK.DPA-Remote configures the IP address, subnet mask, and default gateway.Method 2: Using Ping-ARPUse this section to configure an IP address by manually updating a server’s ARP table and then pinging the PortServer TS 16.1.Record the MAC address of the PortServer TS 16. It islocated on the back of the unit.2.Access a server on the same subnet as the PortServer TS 16.3.Manually update the server’s ARP table using the PortServerTS 16’s MAC address and the IP address you want assigned to the PortServer TS 16. The following is an example of how this is done on a Windows NT 4.0 system:arp -s 143.191.2.1 00-40-9d-22-23-604.Ping the PortServer TS 16 using the IP address just assigned. The following is an example:ping 143.191.2.1The ping will probably time out before there is a response. 5.Wait a few seconds and then ping again.The PortServer TS 16 replies to the ping, indicating that the IP address has been configured.Method 3: Using DHCP or RARP1.Record the MAC address of the PortServer TS 16, which islocated on the back of the unit.2.Set up an entry on a DHCP or RARP server. If you intend touse RealPort, do the following:•Reserve a permanent IP address.•Record the IP address. You will need it when you config-ure the RealPort driver.3.Power on the PortServer TS 16.Method 4: Using the Command Line1.Connect a terminal or PC to a serial port on the PortServer TS16.•For a terminal, use the cable that came in your package. •For a Windows Hyperterminal connection, use the cablethat came in the package, a straight-through DB25-to-DB9 modem cable, and gender changers as required.2.Configure the parameters of the terminal or terminal emula-tion software to work with the serial port. The default port settings are below:3.Log in to the PortServer TS 16 as root by entering the follow-ing commands: (You may have to press the Enter key to get a Login prompt.)•At the login prompt, type root .•At the password prompt, type dbps (which is the defaultpassword. If the password has been changed, use the new password.)See the newpass command in the online Digi One/PortServer TS Command Reference for information on changing the root password.4.Configure an IP address with the following command:set config dhcp=off ip=ip-addr submask=maskwhere ip-addr is the IP address to configure and mask is the subnet mask used by the network Exampleset config dhcp=off ip=192.10.7.3 submask=255.255.255.05.Reboot at the reboot prompt.Step D: Configuring Ports Using the Web Interface1.Access the PortServer TS 16 from a web browser by specify-ing the unit’s IP address in the URL window.2.Log in to the PortServer TS 16 as root by entering the follow-ing:•At the login prompt, type root .•At the password prompt, type dbps (which is the defaultpassword. If the password has been changed, use the new password.)e the web interface to configure ports. See the online helpfor information on configuration fields.4.If you intend to use RealPort, install RealPort software on aserver. See the online RealPort library for more information. Step E: Configure other Features as RequiredSee “Where to Find Information” on this card for ideas onadditional features to configure and directions as to where to find setup information.Step F: Troubleshoot Setup ProblemsEnsure that your setup works as you intend. If you encounter setup problems, see the troubleshooting section in the online Configuration and Administration Guide.PortServer TS 16 LibraryAccess Resource CD CardThis card provides information on the contents of the Access Resource CD. It includes the CD mounting instructions required to access the CD on many Unix systems.Digi One/PortServer TS Command ReferenceThis online manual, available on the Access Resource CD, provides complete information on commands.PortServer TS 8/16 Configuration and Administration Guide This online manual, available on the Access Resource CD, provides procedural information for setup.RealPort Setup GuidesThese online manuals provide information on setting up servers for RealPort software.Digi Port Authority - Remote Device Monitor Setup Guide This online manual provides information on installing and using Digi Port Authority - Remote software. Online Help for the Web UIThis online help provides information on configuration fields used with the web browser configuration interface. Terminal Server Cable GuideThis online manual provides cabling information.•VT 100 emulation • 1 stop bit •9600 baud •No parity•8-bit characterWhere to Find Information Safety Considerations and Warnings•AC only- Do not attempt to defeat the safety feature of the3-wire, ground-connection plug that comes with PortServerTS 16. If you are unable to insert this plug into an outlet,have an electrician replace the obsolete outlet.•AC only- Ensure that the ampere rating of all equipmentplugged into wall outlets does not overload the outlet.•AC only- If you require an extension cord, ensure that theampere rating of all equipment plugged into the extensioncord does not exceed the ampere rating of the cord.CAUTION! This product contains a lithium-ion battery that isembedded in one of the components on the printed circuit board.The battery is not field-replaceable, and improperly installing thecomponent could result in an explosion.CAUTION! Do not cover or obstruct ventilation slots.Thesedevices generate heat and require adequate circulation to maintainproper operating temperatures.CAUTION! Do not switch or disconnect devices in the groundingcircuit conductor between the DC source and the point ofconnection of the grounding electrode conductor.CAUTION! Do not allow the PortServer TS 16 to get wet. Do notinstall near high-powered radio transmitters or electricalequipment. Any of these conditions can cause safety hazards andequipment failure or damage.Rack Mounting Installation•Distribute weight evenly in the rack to avoid overloading.•Ensure proper ventilation with at least 12 inches (30 centime-ters) of clearance on all sides.•Check equipment nameplate ratings before connecting to thesupply circuit to avoid overloads which may damage over-current protection devices and supply wiring.•Maintain reliable earthing for rack-mounting equipment,especially for supply connections.•Install equipment in Restricted Access Areas only (dedicatedequipment rooms/closets) in accordance with Articles 110-16,110-17, and 110-18 of the National Electrical Code, ANSI/NFPA 70.•Connect equipment to a DC supply source (reliably earthed)that is electrically isolated from the AC source.•Directly connect the equipment chassis to the DC supply sys-tem-grounding electrode conductor or a bonding jumper froma grounding terminal bar (or bus) that is connected to the DCsupply system grounding electrode conductor.•Contain equipment that has a connection between thegrounded conductor of the same DC supply circuit, thegrounding conductor, and also the point of grounding of theDC system in the same immediate area. Do not ground theequipment elsewhere.•Locate the DC supply source within the same premises as theequipment.•Route away and secure all DC input wiring from sharp edgesto prevent chaffing as well as provide strain relief.•Provide a readily accessible disconnect device and protectivedevice a fixed wiring for a DC power supply suitable for thespecified rated voltage and current. Disconnect and protectivedevices to be rated 2A Amps maximum.SpecificationsRegulatory NoticesThis product complies with the following standards:Electromagnetic Emissions•FCC Part 15 Class B -- See Also: Declaration of Conformity•EN55022 Class B•EN61000-3-2 and EN61000-3-3•VCCI Class II•ICES 003 Class B•AS3548Electromagnetic ImmunityEN55024Product Safety•UL 60950•CSA 22.2 No.60950•EN60950•NOMS•AS3260Declaration of ConformityIn accordance with FCC Dockets 96-208 and 95-19Digi International declares that the products:to which this declaration relates, meet the requirements specifiedby the Federal Communications Commission as detailed in thefollowing specifications:•Part 15, Subpart B, for Class B Equipment•FCC Docket 96-208 as it applies to Computers andPeripheralsThe products listed have been tested at an External TestLaboratory certified per FCC rules and have been found to meetthe FCC, Part 15, Class B, Emission Limits. Documentation is onfile and available from the Digi International HomologationDepartment.ICES 003 Class BThis digital apparatus does not exceed the Class B limits for radionoise emissions from digital apparatus set out in the RadioInterference Regulations of the Canadian Department ofCommunications.Le present appareil numerique n'emet pas de bruitsradioelectriques depassant les limites applicables aux appareilsnumeriques de la class B prescrites dans le Reglement sur lebrouillage radioelectrique edicte par le ministere desCommunications du Canada.Copyright © 2001, 2002 Digi International Inc. All RightsReserved. DisclaimerThis manual may contain inaccurate or erroneous information. This manual issubject to change at any time. This manual, including all information containedherein, is provided “as is” without warranty of any kind, either express or implied,including, but not limited to, any implied warrantees of merchantability or fitnessfor particular purpose. Digi International Inc. makes no representations,warranties, or commitments with regard to any data or information contained inthis manual. If you rely on data or information contained in this manual, suchreliance is at your own risk.To set up...See...An IP address•The web interface and associated helpNote: The initial IP address cannot be set upwith the web interface.•The set config command in the online Com-mand Reference•The section on configuring the Ethernetinterface in the online Configuration andAdministration Guideautoconnection •The web interface and associated help•The set user and set ports commands in theonline Command Reference•The section on configuring autoconnection inthe online Configuration and AdministrationGuideDPA - Remote•The online Digi Port Authority - RemoteDevice Monitor Setup GuideMenus•The web interface and associated help•The set menu command in the online Com-mand ReferencePorts •The web interface and associated help•The set ports, set flow, and set line com-mands in the online Command Reference•The sections on configuring ports forRealPort, modems, terminals, and printers inthe online Configuration and AdministrationGuidePort Buffering•The web interface and associated help•The set buffers commands in the onlineCommand Reference•The section on Console Management in theonline Configuration and AdministrationGuidePPP•The web interface and associated help•The set user command in the online Com-mand Reference•The PPP section in the Configuration andAdministration GuideRealPort•The web interface and associated help•The set ports command in the online Com-mand Reference•The online RealPort librarySSH•The web interface and associated help•The set user command in the online Com-mand Reference•The sections on Security Features and Con-sole Management in the online Configurationand Administration GuideSNMP agent •The set snmp command in the online Com-mand Reference•The section on configuring the SNMP agentin the onlineConfiguration and Administra-tion GuideUsers•The web interface and associated help •The set user and newpass commands in the online Command Reference•The section on configuring users in the Con-figuration and Administration GuidePower Requirements•16-Port Desktop•16-Port Rack (AC)115-230 VAC,50-60 Hz, .8A maxinternal power supply•16-Port Rack (DC)36-72 VDC, .45 A at 48 VDC maxTerminations:•+ = Source•- = Reference• = Earth groundThe terminal lug must be attachedto a suitable earth ground for safeoperation.EnvironmentalAmbient temperature60°F (15.6°C) to 90°F (32.2°C)Relative humidity20% to 80% non-condensingAltitude0 to 7,000 feet (0 to 2,134 meters)Mechanical16-Port Rack Width: 16.8 inches (42.672 cm)Height: 1.6 inches (4.064 cm)Depth: 6.5 inches (16.510 cm)Weight: 3.75 pounds (1.701 kg)16-Port Desktop Width: 13.5 inches (34.290 cm)Height: 1.375 inches (3.493 cm)Depth: 6.5 inches (16.510 cm)Weight: 3 pounds (1.360 kg)Manufacturer's Name: Digi International Inc.Corporate Headquarters: 11001 Bren Road EastMinnetonka MN 55343Manufacturing Headquarters: 10000 West 76th StreetEden Prairie MN 55344Product Name Model #PortServer TS 16 DesktopPortServer TS 16 Rack ACPortServer TS 16 Rack DC700017337000174270001747See list of product names andmodel numbers.Tested to Comply with FCCStandardsFOR HOME OR OFFICE USE。

万兆强三层核心交换机Web配置手册（适用于US5500-16F8C4TF）1 登录WEB界面1.1 WEB浏览的系统需求使用此系列交换机，系统应该满足如下条件。

1.2 登录WEB配置界面要登录到此系列交换机的WEB配置界面，用户需确认如下条件：●已经对交换机进行了IP 配置，缺省情况下，交换机VLAN1的接口IP地址是192.168.255.1。

●用户保证自己本地PC（管理主机）的网卡的IP是192.168.255.*的网段。

●用户保证自己本地PC的网线接在1-24之间任意一个端口。

●已将一台安装有Web浏览器的主机连接到网络上，并且主机能够PING通交换机。

登录WEB配置界面的操作步骤如下：步骤 1 运行计算机浏览器。

步骤 2 在浏览器的地址栏中输入交换机的地址“http://192.168.255.1”，按回车键。

步骤 3 如图2-1所示，在登录窗口中输入用户名和密码（默认用户名和密码均为admin），单击“确定”。

图2-1 WEB界面登录窗口成功登录后，您可以根据需要配置WEB界面相关参数及信息。

2 系统状态2.1 系统信息【功能说明】在“系统信息”页面，您可以查看设备型号、硬件版本号、固件版本号、设备序列号等信息。

【操作路径】系统状态>系统信息【界面说明】图2-1 系统信息界面表2-1 系统信息界面主要元素2.2 日志信息【功能说明】在“日志信息”页面，您可以查看并下载系统日志。

【操作路径】系统状态 > 日志信息【界面说明】图2-1-1 查看日志界面表2-2-1 查看日志界面主要元素图2-2-2 日志下载界面表2-2-2 日志下载界面主要元素【示例】1.打开tftp32软件；2.在日志下载页面输入tftp服务器地址192.168.120.96和文件名；3.点击“下载”按钮。

如下图：2.3 端口统计【功能说明】在“端口统计”页面，您可以查看端口概要统计和端口详细统计相关信息。

【操作路径】系统状态 > 端口统计【界面说明】图2-3-1 端口概要统计界面表2-3-1 端口概要统计界面主要元素图2-3-2 端口详细统计界面表2-3-2 端口详细统计界面主要元素2.4 Lacp状态【功能说明】在“LACP 状态”页面，您可以查看LACP系统状态信息。

PortServer TS 8 or 16 to ConnectPort TS 8 or 16The PortServer TS 8/16 are products Digi International has been manufacturing for over 15 years. The ConnectPort TS 8/16 are newer products which are similar in core functionality, but which offer enhanced performance, better security, better manageability, customization options, and additional features important in the modern device connectivity environment.The ConnectPort TS uses the same driver and offers the same pinout as existing PortServer TS products; therefore most existing applications are drop-in replacement.Additional hardware features:∙Dedicated console port∙LEDs on each port to indicate data activity.∙USB flash drive support -- ability to use USB flash drives for programming and storage.Additional firmware capabilities:Security:∙Web proxy support to allow use on networks where this is required.∙Configure non-default user names that have various levels of device control o no longer required to use the name “root”o can have users with some, but not all configuration, capability fortroubleshootingFlexibility:∙Device initiated RealPort support – the ConnectPort TS can be configured to connect to the Computer hosting the RealPort driver.∙Product customization capabilitieso Integrators can pre-load different defaults when the unit is sent to a location or hardware reset to defaults.o The look and feel of the device can be managed to show a custom logo image or web style sheet in the webserver. This capability allows the ConnectPortTS to more closely align with the look and feel of other software componentsin an integrated solution.∙Python programmability -- to monitor data flow at the individual device level and take autonomous action, and/or to log data to a local (flash/usb) file.Manageability:∙Digi Remote Manager support∙Mass-configuration deployment tools are available to pre-load customization or tosimply preconfigure the device prior to deployment.Configuring the ConnectPort TS for the most typical applicationsThis technical note is intended for solution implementers and describes how to implement typical configurations analogous to PortServer TS configurations via web and via cli.Via the Web: Most initial testing of the product is done via the web page. The Web page of the ConnectPort TS is very similar to the PortServer TS configuration web page.Serial port profile options are provided under the serial ports supporting the different connection profile types: (RealPort, Console Management, TCP Sockets, UDP Sockets, Serial Bridge, Local Configuration, Industrial Automation, Modem Emulation, and Custom). These generally behave similarly with default options that are generally compatible with the default options offered by the PortServer TS 8 and 16.Login: root/dbpsFor RealPort:Configuration→Serial Ports→Port#→Profile: Realport→ApplyConfiguration→Serial Ports→Port#-->Copy—Select all ports→Apply For TCP Sockets:Configuration→Serial Ports→Port#→Profile: TCP SocketsScroll Down to Basic Serial settingsBaud rate: 38400 {other flow control settings as needed} →Apply Configuration→Serial Ports→Port#-->Copy—Select all ports→Apply The network configuration supports DHCP or static IP for IPv4.Via the Dedicated Console Port: The configuration of the product is similar to PortServer in many respects. The dedicated console port is configured for 9600 8, N, 1 and uses the same pinout as the numbered ports. These commands can also be given via ssh or telnet.Slight differences in syntax:For those customers used to configuring using the “#>set profile options, this is now#>set profile profile=[value] port=## instead of#>set profile profile=[value] range=##Note: the values for serial ports are now all managed under #>set serial port=## instead of set port set line & set flow.Login: root/dbpsFor RealPort:#>set profile profile=RealPort port=*For TCP sockets:#>set profile profile=tcp_sockets port=*#>set serial port=* baud=38400 (the default is 9600)#> set serial port=* flowcontrol=none {or other settings as required}#>set serial ?Shows the syntax for the flow control and other serial port settings To set the network address manually via the CLI#> set network ip=[ipaddr] submask=[subnet mask] gateway=[gateway ip] static=on dhcp=offAdditional information:ConnectPort TS product Support Page:/support/productdetail?pid=3019RealPort Drivers and information (same driver as PortServer TS products)/support/productdetail?pid=3037Quickstart Guide/support/documentation/90000848-88_D.pdfComplete syntax for CLI is described in the Command Reference Manual:/support/documentation/90000566_N.pdfUser Manual/support/documentation/90000565_P1.pdfCabling Guide (same cables as PortServer TS products):/support/documentation/90000253_G.pdfDevice Customization/Customized Default information:/support/documentation/90000734_B.pdfDigi Remote Manager/Device Cloud/support/documentation/html/90001150/Current/Default.htm。

1.Configure the PortServer TS serial ports in Realport, connected behind a Digi ConnectWan 3G with port forwarding acting as an internet gateway.Objective: Step by step instructions to configure the PortServer and the Digi Connect Wan 3G to allow access via Realport to several serial devices from the Internet.1.1Software Requirements-Digi Device Discovery Utility-PuTTy or any Terminal application1.2Hardware Requirements-Digi Connect WAN 3G with a Internet enabled APN allowing incoming connections-Digi PortServer TS-Serial device(s) or a laptop computer / loopback adapter for testing purposes.2.Theory of OperationCommunications applications such as SCADA polling, remote printing, or other hots-initiated tarffic can be sent over the cellular network to the remote device or devices via the Digi Connect WAN 3G. The Digi Connect WAN 3G forwards IP traffic, in this case Digi’s patented Realport protocol destine d for a specific port or port range on the cellular interface, to a private IP address on the ethernet “side” of Digi Connect WAN 3G.This process uses Network Address Translation (NAT) where only the mobile IP address is visible to the outside and TCP/UDP port forwarding entries direct traffic from the mobile IP address of the Digi Connect WAN 3G to the appropirate device.For example, an application on the host computer communicates via COM ports. The Realport COM port redirector driver is configured to use the mobile IP address of the rmote Digi Connect WAN 3G. A port forwarding entry on the Digi Connect WAN 3G direct the realport traffic, which uses TCP Port 771, to the Digi serial server.3.Diagram and Setup InstructionsRealport Installed and configuredto map COM portsTo Connect WAN 3G mobile IP Addr.Mobile IP addr :80.187.15.5Eth IP addr :192.168.1.1Port Forwardingentries forRealport TCPport 771Multipleserialdevices1)PortServer TS Configuration :a)Connect the PortServer TS on the same network as the computer to be able to access the webinterface, using the Digi Device Discovery locate the device on the network and double click it’s IP Addressb)On the web interface, navigate to Configuration>Serial Ports, and change the profile of eachports to “Realport” then click Apply.c)Next, navigate to Configuration>Network and select “Use the Following IP address” andenter a fixed ip address, in this example :a.IP Address : 192.168.1.20b.Subnet Mask : 255.255.255.0c.Default Gateway : 192.168.1.1 (This is the IP address of the Digi Connect WAN3G)d)Click Apply. The Configuration of the PortServer TS is done and connection to it will belost due to the new network settings.2)Connect WAN 3G Configuration:a)Connect the Digi Connect Wan 3G on the same network as the computer to be able to access theweb interface, , using the Digi Device Discovery locate the device on the network and doubleclick it’s IP Addressb)On the web interface, make sure the mobile settings are configured properly, 3G connection isestablished and the device obtained an IP address (Administration > System Information >Mobile > Mobile Statistics) if not, go to Configuration > Mobile and enter the settingsmatching the SIM cards, click apply and reboot.c)! Warning ! Make sure to note down the mobile IP address of the device as it will be neededat the end of this process and access to the unit via Ethernet will not be possible as it will be connected to the PortServer deviced)Navigate to Configuration>Network Services Settings and uncheck the “Enable Realport”box (This will disable the Connect Wan 3G listening on the Realport TCP port) and click Apply.e)Navigate to Configuration>Ip Forwarding Settings, in the “Current Settings for Nat Instance1:”check the “Enable Network Address Translation (NAT)” box and chose NAT PublicInterface mobile0f)Scroll down to the “Forward TCP/UDP/FTP connections from external networks to thefollowing internal devices (you may configure up to 64 forwarding rules):” section andconfigure the following :a.Enableb.Protocol : TCPc.External Port : 771d.Forward to Internal IP Address : 192.168.1.20 (PortServer TS IP address)e.Forward to Internal Port : 771f.Range Port Count : 1g)Click Addh)Click Applyi)Navigate to Configuration>Network, select “Use the following IP address :” and enter a fixeip address matching the “Default Gateway” used on the PortServer TS, like in this example :a.IP Address : 192.168.1.1b.Subnet Mask : 255.255.255.0c.Default Gateway : 0.0.0.0j)Click ApplyNow connect the Ethernet cable between the Digi Connect Wan 3G and the PortServer TS3)Realport Installation :a)Launch the Realport installation from the computer (Realport drivers can be downloaded fromDigi’s ftp at : /support/driver/40002549_E.zip)b)Select Add a New Device and click Nextc)Wait for the scan to finish and chose “Device not listed”, click Nextd)In the Network Settings section, select IP and enter the Mobile IP Address of the Digi ConnectWan 3G.e)In the COM Port Settings, set the number of Ports to the PortServer’s port numbers (Example, 4for a TS4)f)Click Finishe)New serial ports will be installed, the first Realport COM (Starting COM) being Port 1 of thePortServer TS.f)Connect the serial device, a loopback connector or another computer to any of the serial ports ofthe PortServer TSg)Open the application for the serial device or any terminal application to the matching RealportCOM port of PortServer TS, Data should be displayed.。

GermanySoftwareManualandDevice Driver forand theInternational Inc. All other brand and product names are the trademarks oftheir respective holders.All Rights ReservedInternational Germany Phone732 13 1813-06 Tower ‘A’FAXNgee Ann City Singapore 0923Information in this document is subject to change without notice and does notrepresent a commitment on the part ofprovides this document “as is”,without warranty of any kind, either ex-pressed or implied, including, but not limited to, the implied warranties offitness or merchantability for a particular purpose.Table of Contents Introduction (4)Overview (4)Software Installation (5)Copying the Files (5)Configuring the (7)RemovingMonitor Utility (10)Loading the Monitoring Utility.................................................................. (11)Stopping (11)Remote BootingSupport Services (14)TheServer (15)World Wide Web Server (15)Device Driver for Novell NetWareBe sure to read the Release Notes that may be included withthis software device driver. The Release Notes containinformation not available at this manual’s press time.4 andSoftware Installationsimply copy the relevant fi The filesyour file server.(AIOPSDRU . NLM, AIOPSCFG . NLM,A IOPSBOT . NLM and A IOPSMON . NLM) should be copied to the system directoryof the file server, typically called FDevice Driver for Novell NetWareConfiguring thehardware you have installed configuration program, AIOPSCFG . NLM, writesA IOPSDRUdriver, make sure the driverName TCP PortD e l e t eO p t i o nS e t6 andAddingand pressenter the name assigned during installation of theUser’s Guide and Reference Manual).The driver supports up to sixteen yourscreen will now look like this:Setup Utility u 1.01O p t i o n sO p t i o ns e tE x i tRemovingand press <Enter>. A new pointer will appear next to the firstyou wish to delete, and presswill be removed from the configuration box.Hunt GroupsTheUser’s Guide and Reference Manual). When the Huntgroup option is set in theTCP Port NumberThis parameter is reserved for futureTo set the TCP port number to the default value, use the arrow keys to position the pointer next to Set TCP Port, and pressdriver configuration, either use the arrow keys to position the pointer next to Exit, and press <Enter>, or simply press (yes). If you havemodified the configuration you will now be asked if you wish to save the configuration. PressAUTOEXEC . NCFfile used to set up will loadCL IB . NLM, STREAMS. NLM and SNMP . NLM before it loads.LOAD\ETC\HOSTS tile to find networkUser’s Guide and Reference Manual, under Setname anddriver, enter the following command on the server’s console:load aiopsdruUpon successfully loading the driver, the following banner message (or similar) will appear:NetWareInternational, Inc. All rights reserued.Device Driver for Novell NetWareName Brdt HREU SREUP S16 1.20.9AddstopOptionset TCP Port10To start aand pressin the configuration box. Use the arrow keys to position the pointer next to theStatus (see the example above) will be changed to “Act iue”. Starting aTo stop aand press <Enter>. A new pointer will appear next to the firstyou wish to stop, and press <Enter>. TheBefore powering down ato the configuration, use the arrow keys to position the pointer next to Addenter the name assigned during installation of theUser’s Guide and Reference Manual).Follow the procedure above to start the newDevice Driver for Novell NetWareRemote Booting PortServersTheUser’s Guide and Reference Manual for information on setting up thesoftware from a Novell server, create a directory F IG I, copy the new bootCOPY A Fpower switch off, then back on. Thehas booted up, A IOPSBOT may be unloaded. The upgraded software will remain in effect until theThe boot filename and the IP address of the boot host mustbe registered in theUser’s Guide and Reference Manual).Example:setset12 andError MessagesThe following error messages are generated by the driver:ERROR- PortSeruer not respondingERROR- Did not establish connection to PortSeruerCheck to be sure that thename and IP address are configured properly and entered in F to verify that it is operational (use PING . NLM).ERROR- Probably lost connection: Terminating Seruer ERROR- Receiued illegal packet: Terminating Seruer ERROR- Receiued reset from seruer: Terminating Seruer Fatal error-rebootprovides an electronic bulletin board service (BBS) for our customers. This bulletin board provides general and technical information aboutBBS allows users to download software drivers as soon as they become available. There is also a feature to allow users with problems or questions about Technical Support.Using the In Europe, dial735 2460. The bulletin board accepts callsat 1200, 2400, 9600 andstandards are supported, with full MNP class l-5 error correction and data compression.The recommended modem communications parameters are 8 bits, no parity and one stop bit (8 N 1). Other settings may also work.Download protocols include Zmodem, Xmodem, Ymodem, Kermit and others. 14Internet FTP Serverserver for those with access to the Internet network. The address is f tp .digibd .com. Log in asanonymous, and enteryour E-mail address when asked for a password. Drivers and installation tips arelocated in the givesinformation on uncompressing the files after downloading. Tip: Be sure to enterLAN card: Type:port used:Operating system:Support ServicesSupport Services17Return ProceduresAllasks that you to resolve any difficulties by contacting our Technical Support representatives at (612) 943-0578.necessary to obtain an RMA (Returned Merchandise Authorization) num-ber from Customer Service representative. Author-ized returns should be shipped toProducts received without an RMA number clearly markedon the outside of the package will be returned, unopened, tothe sender18。