电梯专用英语
- 格式:docx
- 大小:64.22 KB
- 文档页数:56
电梯专业英语词汇----------------------------------------------abbreviation 缩语abnormal "不正常的,反常的" abnormality monitoring 异常监听abrasion 磨损abrasion resistant 耐磨性abrasive cloth 砂布absorb 吸收absorber 减振器AC drive 交流拖动AC feedback control 交流反馈控制AC motor 交流电机AC servo 交流伺服AC servo motor 交流伺服电机AC single speed 交流单速AC two speed 交流双速AC two speed motor 交流双速电动机AC variale speed 交流调速AC(alternating current) 交流电acanning cycle 扫描周期,扫描循环acceleration control system 加速度控制系统acceleration(accel)rate 加速率accelerator 加速器acceptance of lift 电梯验收acceptance period 验收阶段acceptance test 验收试验acceptanec certificate 验收证书access door 检修门access forbidden 禁止入内access lift 通道电梯access security 通道防卫access switch "通道开关,维修用开关" access way 进出通道accessibility "可通达性,接近的,难易程度" accessible 允许进入accessible space 允许进入的场地accessory "配件,附件"accident 事故accident insurance 事故保险accident prevention 事故预防accidental contact 触电accidental operation 误操作accordion door 折叠门accumulation 累积accumulator 蓄电池AC-GL machine 交流无齿曳引机acoustic "听觉的,声音的"acrew die 板牙activate "启动,触发"active mode 主动模式actual condition "实际状况,实际条件" actual load 实际载荷actual state 实际状况actual value 实际值actuate "开动,操作,激励"actuating linkege 操作连杆actuating magnet 操作磁铁actuation time 动作时间actuator "操纵机构,激励器,螺线管" actuator bracket 调节器支架actuator plate 调节板ACVF drive 交流调频拖动ACVF system 交流调频系统ACVF(AC varible frequency) 交流调速ACVV dirve 交流调压拖动ACVV system 交流调压系统ACVV(AC varible voltage) 交流调压adaptation "适应,匹配"adapter PCB 选通脉冲印刷电路板adapter(adapator) 适配器adapting 选配adaptive control system 自适应能力控制系统addendum "齿顶高,附录"addendum circle 外圆adding working drawing 附加加工图addition "附加物,加法"additional materials 附加材料address 地址adhesion "胶,粘合胶"adhesion protective oil 防粘油adhesive foil 胶粘薄膜adhesive tape 胶带adjacent 邻近的adjacent car "相邻轿厢,相邻电梯" adjacent entrance 相邻出入口adjusment 调试adjustable condensor 可变电容器adjustable resistance 可调电阻adjustable spanner 可调扳手adjustable speed electric drive 调速电力拖动adjustable wrench "活动扳手,可调扳手" adjusting screw 调节螺丝adjustor 调试员administation overjhead rate 管理费用标准administration cost 管理成本administration expenses 管理费用advance door opening 提前开门advance payment 预付款advanced "提前的,先进的"advanced carriage 超前拖板(选层器)advancing position reference value 超前位置参考值aerial cableway "空中缆车,架空索道"aerial ropeway "空中缆车,架空索道"aerial tramway "空中缆车,架空索道"aesthetic 美观after sales service 售后服务agency 代理agenda 议程air cord (门机用)航空钢丝绳air purifier 空气滤清剂air ventilator 通风管air-bleed 空气分泄器airborne noise 空气传播噪声air-condition 空调air-gap 气隙alarm 警报alarm bell 警铃alarm button 警铃按钮alarm buzzer 警报蜂鸣器alarm circuit 警报电路alarm system 警报系统ALC(autoclaved light-weight concrete) 蒸压轻质混凝土alcove arrangement 电梯U型排列法algorithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignment gauge 校正量规alkali 碱all-computer-controlled 计算机全控的allocation "分配,分派"allocation of landing call 层站呼梯指令分配allowance "允用误差,加工余量"allowble stress for temporary load 允许暂时应力值alloy 合金alloy steel 合金钢alteration 改进alternate floor 隔层alumina 氧化铝aluminum 铝aluminum alloy 铝合金aluminum bronze 铝青铜aluminum cladding 铝制包层alumite 防蚀铝alundum 氧化铝ambient 环境的ambient noise 环境噪音ambient temperature 环境温度ammeter 安培计ammonia 氨amperage 电流强度ampere 安培amplification 放大amplification stage 放大等级amplifier 放大器amplifying tube 放大管amplitude 幅度analog adder 模拟加法器analog computer 模拟计算机analog speed card 模拟曲线板analog-digital converter 模拟-数字转换器analogue(analog) 模拟analysis 分析analysis mode 分析模拟anchor bolt 地脚螺栓anchorage "锚具,锚定"angle bar 角钢angle guide 角铁导轨angle iron 角铁angle iron frame 角铁框架angle of contact 接触角angle of deflection 导向角angle of inclination 倾斜角angle of lead 导程角angle of traction 曳引机包角angle of wrap 包角angle steel 角钢angular contact ball bearing 向心推力球轴承angular contact bearing 角面接触滚动轴承angular gear 斜齿轮angular retardationg 角减速度angular velocity 角速度anneal 退火annealing 退火annual inspection 年检annual report 年度报告annunciator "报音器,声音合成器"anode 阳极anodize 氧极氧化ANSI(America Nationa Standard Instirute) 美国国家标准协会anti-clockwise 逆时钟方向anti-corrosive paint 防腐蚀漆anti-creep 防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰anti-nuisance device 防捣乱装置anti-phase braking 反向制动anti-phase current 反相电流anti-rebound of compensation rope device 补偿绳防跳装置anti-residual 防剩磁anti-resonance 抗谐振anti-reversion device 防反转装置anti-rust 防锈anti-stall 防空转anti-vibralion pad 防震垫APM(automatic people mover) 自动人员运输机apparen power 视在功率apparent output 视在输出applicant 申请人application 申请application guide 应用指南aprons 裙板arbour "轴,杆"arc chamber 电弧隔离室arc protection 防电弧arc quenching 熄焊弧arc shield 电弧屏蔽arc suppressor 灭焊器architect 设计单位architecture 建筑学architrave 门框area 面积arm "臂,支路"armature 电驱armature coil 电驱线圈armature current 电驱电流armature lamination 电驱铁芯片armature shaft 电驱轴armature spider 星形轮armature winding 电驱绕组armoured 蛇皮管的armoured cable 蛇皮管电缆armoured conduit 导线管arrangement 布置arrival bell 到站铃arrival buzer 到站蜂鸣器arrival floor 到达楼层arrival gong 到站钟arrival rate 到站率article of consumption 消耗品artificial intelligence 人工智能artistic 工艺artistic face 工艺表面asbestos packing 石棉盘根ascending 上升ASIC(application specific integrated circuit) 专用集成电路assemble 装配assembler language 汇编语言assembly of hinge 铰链组装assign 分配astragal 装饰镶条atmospheric influence 大气影响attachment 附件attendant control 有司机控制attendant control compartment 有司机控制盒attendant operation 有司机操作audible signal 音响信号audio tape recording 磁带录音authority "当局,核准部门"authority of lift acceptance 电梯验收部门authorized "授权的,核准的"authorized user 核准使用者auto-adaptation 自适用AutoCAD 自动计算机辅助设计autographic recoder 自动记录仪automatic 自动的automatic allocator 自动分派器automatic by-pass 自动直驶automatic center opening sliding door 自动中分式滑动门automatic closer 自动关闭门automatic dispatch 自动调度automatic door 自动门automatic homing 自动回基层automatic landing 自动停站automatic landing system by spare battery 靠备用蓄电池的自动停站设备automatic leveling 自动平层automatic lubricator 自动润滑装置automatic parking garage 自动停车库automatic parking system 自动停车系统automatic relevelling 自动平层校正automatic rescue device 应急救助装置automatic return 自动返回automatic telescopic center opening sliding door 自动中分式折叠滑动门automatic telescopic sliding door 自动折叠式滑动门automobile lift 汽车电梯autowalk 自动人行道auxiliary apparatus 辅助装置auxiliary brake 辅助制动器auxiliary cicuit 辅助电路auxiliary contact 辅助触点auxiliary drive 辅助驱动auxiliary lock 辅助锁auxiliary materials 辅助量auxiliary value 辅助材料auxiliary winding 辅助绕组available area 有效面积average 平均average car load 平均轿厢负载average dispatching interval 平均调度间隔时间average interval 平均调度间隔时间average passenger waiting time 平均乘客侯梯时间average response time 平均应答时间average waiting quest 平均乘客量average waiting time 平均乘客侯梯时间axial flow fan 轴流式风扇axis 轴线axle 轴babbit 巴氏合金babbit lined bearing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器babbit metal 巴氏合金babbit rope socket 灌注式巴氏合金绳头back current 反向电流back e.m.f 反电动势back lash 轮齿隙back plunger type 后部柱塞式(液压梯)back side "后侧,后边"back type governor 轴流式限速器back wall 后壁baked enamel 烤漆balace weight 平衡器balance 平衡balance chain 平衡链balance coefficient 平衡系数balanced traffic 平衡交通ball bearing 滚珠轴承ball cup 球形碗ball pin 球形硝ball stop valve 球形断流器ball type bearing 滚珠轴承ballast 镇流器balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade lighting 扶手照明balustrade panel 扶手板balustrade skirting 扶手群板balustrades 扶手装置bandsaw 带锯bank "银行,群组,排"bar "条,棒"bar code 条形码bar lock 杆式锁bare wire 裸线barricade "防护墙,隔墙"barrier "隔板,栅栏"base "基座,基础"base plate 基板basement 地下室basement service 底下室服务basement type 底吊式basic logic element 基础逻辑元件basic logic function 基础逻辑功能batch production 批量生产battery 电池battery- backed 电池支持的battery box 蓄电池箱battery charger 电池充电器baud rate 波特率BCD(binary coded decimal) 二进制编码的十进制beam 梁beam pad 井道内电缆保护垫片beam pulley 抗绳轮bearing 轴承bearing bracket 轴承支架bearing cap 轴承盖bearing load 轴承负荷bearing plate 承重板bearing play 轴承间隙bearing sleeve 轴承衬套bearing stand 轴承座bed lift 病床电梯bed plate 底座bell 铃belt 胶带belt drive 胶带传动belt grinder 胶带磨床belt pulley 胶带轮belt type moving walk 带式自动人行道bending 弯曲bending stress 弯曲应力benzine 轻汽油bevel gear 伞(斜)齿轮beveled washer 斜垫圈BGM (background music) 背景音乐BGM speaker 背景音乐扬声器bias "偏置,偏移"bid "投标,报价"bid table 报价单bidder 投标bidding cycle 投标有效期限bidding procedure 投标(报价)程序bil of delivery 发货单bil of lading 海运提单bill of expenses 费用帐单bill of materials 材料单billing 开发票binary 二进制binder 装订册bi-parting 对开式(上下开启)bi-parting door 垂直中分门bipartite light transistor 双分式光电管bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关bitumen 沥青blade "叶片,刀片,锯片"blade connector 刀形连接器bleed-off circuit 泄放电路blind hoistway 盲(无门)井道block chart 方框图block diagram 方框图线路block of flats 住宅楼区blocking of control circuit 控制电路闭锁blower 鼓风机blower coil 吹弧线圈blower motor 风机电动机blue print 蓝图boading floor 登梯楼层boading time 登梯时间boarding 登梯boarding landing 登梯层站boarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站boarding zone 登梯区域bobbing 绕线管boldface type 粗字体bolt 螺杆booster 升压机border condition 边界条件bore hole "钻孔,镗孔" boring 镗boring lathe 镗床boring machine 镗床boring miller 镗铣床bottom 底部bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程bottom car runby 底部轿厢越程bottom clearances for car 轿底间隙bottom counterweight clearance 轿底对重间隙bottom counterweight overtravel 轿底对重越程bottom counterweight runby 轿底对重越程bottom door retainer 门下角bottom floor 底部楼层bottom runby 底部越程bottom slow down switch 底部减速开关bottom stop 底部停战bottom terminal floor 底部楼层bottom terminal landing 底部端站bottom terminal stop 底端停站box "盒,箱"box counterweight 箱式对重Braille 盲文字符brake 制动器brake arm 制动器臂brake contact 制动器触点brake coutact 制动器联轴器brake dish 制动盘brake drum 制动轮brake energy 制动力brake level 制动器杠杆brake lever 制动器手柄brake lining 制动器衬套brake linkage 制动器连杆brake operater switch 制动操纵开关brake pin 制动器悄brake press "折弯机,压弯机"brake pulley 制动轮brake release lever 制动器松闸手柄brake release magnet 制动器送闸磁铁brake release time 制动器松闸时间brake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧brake tension 制动器张紧力brake torque 制动器力矩brake wrench 制动器板手braking 制动braking distance 制动距离braking force 制动力branch circuit 分支电路brass founder 铸铜break "切断,破断"break-down 故障breaking load 破断负荷breaking strength 破断强度breaking test 破坏实验breather 通气管brick 砖brick-layer 砖砌工bridge circuit 桥式电路bridge connector 桥接器bridge jumper 桥接片bridge rectifier 桥式整流器bright controlling 光度控制broach 拉力broaching machine 拉床brochure 手册broken chain contact 断链触点broken circuit 断路broken drive chain contact 主驱动链保护装置broken drive-chain safety device 驱动链条保护装置broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点broken step chain device 断绳开关broken step chain safety device 梯级链断列触点broken step safety device 梯级破列安全装置broken tape sweitch 短带开关bronze 铜brunching "成组,成群"brush finished stainless steel 哑光不锈钢brush holder "刷握,滑环"brush yoke 刷架budget 预算buffer 缓冲器buffer base 缓冲器底座buffer plate 缓冲器板buffer plunger 缓冲器柱塞buffer return spring 缓冲器复位弹簧buffer stand 缓冲器台buffer striking plate 缓冲器撞板buffer stroke 缓冲器冲程buffer support 缓冲器支承buffer switch 缓冲器开关buider's work drawing 土建图纸buiding facility 大楼设施buiding supervision center 大楼监管中心builder 建筑单位building 建筑building area 建筑面积building contractor 建筑承包商building manager 大楼管理者building monitoring and security system 大楼监管和安全系统building population 大楼居住人口built=in 内装built-in escalator 组合式自动扶梯bumper 弹簧式缓冲器bumper rail 防撞板bumpy ride 颠簸振动的运行buried 埋入的burn in (程序)灌入burr "毛刺,毛边"burr free 去毛刺bus 总线bus bar 汇流条bush 衬套bushed bearing 加衬轴套bushing "衬套,轴套,套筒"butt joint "平接,对焊"button 按钮button switch 按钮开关buyer 买方buzzer 蜂鸣器buzzer switch 蜂鸣器开关bypass 直驶by-pass button 直驶按钮by-pass valve 溢流阀bypassed floor 直驶不停楼层bypassed stop 直驶不停层站C$F 到岸价cab "轿厢,座舱"cab interior 轿厢内部cabin "轿厢,座舱"cabinet "柜,厢"cable 电缆cable box 电缆箱cable car 缆车cable cleat 电缆夹具cable conductor 电缆导线cable entry 电缆引入cable hanger 电缆吊架cable hole 电缆孔cable joint 电缆接头cable termination 电缆末端cable trunk 电缆接头CAD 计算机辅助设计cage 轿厢cage door 轿厢门calculation 计算机辅助设计calibrate 校准call "呼梯,呼叫"call acceptance 呼梯接收call accepted 接受呼梯call accepted indicator 接受呼梯指示灯call accepted signal 接受呼梯信号call allocation 呼梯分派call assignment 呼梯指令分配call band 呼梯信号带call button 呼梯按钮call cancel 呼梯取消call canceling 呼梯取消call coincidence 呼梯重合call conmting system 呼梯计数系统call contrl 呼梯指令控制call emitter 呼梯指令发送器call input 呼梯输入call input capacity 呼梯输入内容call input device 呼梯输入装置call load 呼梯输入call memory 呼梯记忆call registered 登陆的呼梯call registered signal 登陆的呼梯信号call registration indicator 呼梯登陆信号call sequence 呼梯顺序call tegistration 呼梯登陆call-back 召修call-back message 召修信息callinfg board 召唤盒calling floor 呼体楼层calling landing 呼梯call-out response time 维修召唤应答时间call-out service 急修服务CAM 计算机辅助制造cam 凸轮cam for positive operation 强制操纵凸轮cam lever 偏心柄cam shaft 偏心轴cam tape control 偏心带控制cam-gear 凸轮传动装置cam-operated switch 凸轮(碰铁)操纵开关cancel "撤消,取消"cancelingof call signal 呼梯信号消除cancellation "撤消,取消"canopy "顶盖,大蓬"canvas 帆布canvas hose 帆布软管cap "帽,盖子"cap nut 螺母capacitance "电容,电容量"capacitor 电容capacitor motor 电容器电机capacity "载重,容量,定员"capacity plate 载量标牌capstan 绞盘captive roller safety gear 滚柱式安全钳car 轿厢car annunciator 轿厢报警器car approaching gong 轿厢到站预报钟car apron 轿厢入口群板car assignment "轿厢调度,轿厢分配"car automatic switch landing 轿厢开关自动停站car axis 轿厢中心线car back wall 轿厢后壁car botom clearance 轿厢安全高度car bottom overtravel 轿厢底部越层car bottom runby 底部越程car buffer 轿厢缓冲器car button 轿厢按钮car cab 轿厢体car call 轿厢指令car call button 轿厢指令按钮car call cancel 轿内召唤取消car call control 轿厢指令控制car call panel 轿厢(呼梯)指示盘car call stop 轿厢(呼梯)指令停车car cam 碰铁car canopy 轿厢顶盖car ceiling 轿厢装饰顶car coming indicator 轿厢驶近指示灯car control lever 轿厢操纵手柄car control switch 轿厢操纵开关car counterweight 轿厢对重car cross-head 轿厢上梁car depth 轿厢深度car dispatch 轿厢调度car door 轿门car door catch 轿门栓car door closer 轿门关闭器car door electric contact 轿门电触点car door guide shoe 轿门导靴car door interlock 轿门联锁car door lock 轿门门锁car door rail 轿门导轨car door sill 轿门地坎car door track 轿门导轨car elevator 汽车电梯car emergency exit "轿厢安全门,应急门"car emergency opening 轿厢安全窗car emergency release switch 轿厢应急释放按钮car enclosure panel 轿厢壁板car enclosures 轿厢壁板car entrance 轿厢入口car extetior "轿厢外装修,轿厢外表"car fan 轿厢风扇car floating movable platform 轿厢活动地板car floor frame "轿厢架,轿架"car frame "轿厢架,轿架"car frame attachment 轿厢框架附件car frame plank 轿厢下梁car frame upright 轿厢立柱car front 轿厢前壁car full control 满载轿厢控制car gate 轿厢门car gate contact 轿门触点car gate electric contact 轿门电气触点car guide 轿厢导轨car guide axis 轿厢导轨中心线car handle control "手柄开关操纵,轿内开关控制" car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明car isolation 轿厢隔震器car leveling device 轿厢平层装置car lift 汽车电梯car light 轿厢照明装置car light panel "轿厢照明板,照明天花板"car lighting 轿厢照明car manual switch landing 轿厢手动开关停站car operation board 轿厢操纵盘car operation panel 操纵箱car overload 轿厢超载car panel 轿厢壁板car panel attachment 轿厢壁板附件car panel base 轿厢壁板底座car panel with window 轿厢壁板上窗口car platform "轿厢底,轿底"car platform guard 轿厢站台护板car platform sill 轿厢car position indicator "轿厢指示灯,轿厢位置显示" car position reference value 轿厢位置参考值car preference 轿厢优先权car push-button 轿厢按钮car rear wall 轿厢后壁car roof "轿厢顶,轿顶"car safety 轿厢安全钳car safety bar for dumbwaiter 轿厢安全棒(杂货梯) car safety gear 轿厢安全钳car safety mechanism switch 轿厢安全钳联动开关car sheave 轿厢绳轮car side emergency door 轿厢安全侧门car side opening 轿厢侧面开门car side wall 轿厢侧壁car sill 轿厢地坎car sling "轿厢架,吊架"car station 轿厢操纵站car status information 轿厢运行状态信息car stop 轿厢停止car suspension 轿厢悬挂装置car switch 轿厢开关car switch automatic floor stop operation 轿厢开关自动停站装置car switch control 轿厢开关控制car switch opration "手柄开关操纵,轿内开关控制" car top 轿厢顶部car top clearance 轿顶安全高度car top emergency exit "轿顶安全出口,轿顶应急出口" car top guard 轿顶护栏car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站)car top light 轿顶照明装置car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆car ventilation 轿厢通风car walls "轿厢壁,轿壁"car weight 轿厢重量car width 轿厢宽度carbon "碳,石墨"carbon brush 碳刷carbon contact 碳精触点carbon steel 碳素钢carburization 渗碳carburize 渗碳carburized hardening 渗碳硬化carburizer 渗碳剂card "卡片,纹板"card reader 卡片读出器cardan joint 万向接头carpet 地毯carriage charges 运费carry frequency "载波频率,开关工作频率"carrying capacity "载运量,载运能力"cart elevator 车辆运货电梯cartridge fuse 插塞式熔断器carving machine 刻模机cascade "级联,串联"cascade sub-loop 串接式子回路case "箱,盒,外壳"casing "保护套,外套"casing of cylinder 油缸套cassette tape 录音带cast bronze 铸青铜cast iron 铸铁cast steel 铸钢casting 铸造castor oil 蓖麻油catch "擎子,门扣,捕捉器"catch block 安全钳catch clip 捕捉夹钳catch device 捕捉装置cathode 阴极cathode ray tube(CRT) 阴极射线管cavitation "气穴,涡穴,饱和压力点"ceiling 吊顶ceiling assembling 轿顶cellulose 纤维板cement "水泥,胶合剂"cement concrete 混凝土cenrifugal brake 离心制动器center 中心center latch 中心门栓center line 中心线center of curvature 曲率中心center opening 中分式门center opening door 中分门center opening two speed door 中分四扇门center opening vertical sliding door 中分式垂直滑动门center plunger hydraulic lift 柱塞直顶式液压电梯center support "中心支撑,中间支撑,第三支撑" center-opening folding door 中分式折叠门centigrade 摄氏温度central alarm 中央报警central control board 中央监控盘central control room 中央监控室central jack 中心液压装置central position 中心位置centrifugal 离心的centrifugal cast 离心铸造centrifugal fan 离心式风扇centrifugal governor 离心式限速器centrifugal speed 离心速度centrifugal switch 离心开关centrifugal type governor 离心式限速器centripetal force 向心力ceramic capacitor 搪瓷电容certification 证书certifying body 认证机关chain 链条chain block 手拉葫芦chain bracket 链条托架chain drive 链传动chain drive elevator 链驱动升降机chain drive machine 链驱动机chain gear 链轮chain guard 链防护罩chain link "链节,链环"chain pitch 链条节距chain sag 链条下垂度chain sheave 链轮chain sprocket 链轮chain sustarned elevator 链支撑升降机chain tensioning device 链张紧装置chain wheel 链轮chain wheel track 链轮导轨chamger "倒棱,去毛刺"change switch 转换开关change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性channel 槽钢channel iron 槽铁channel steel 槽钢character "特征,字符"characteristic "特征,特性" characteristic curve 特性曲线charge "充电,收费"charged "带电,充电"charging contactor 充电接触器charging set 充电chart 图表chart of accounts 成本图表check valve 止逆阀chequer(checker)plate 网纹钢板chief engineer 总工程师chime 音钟chip 芯片chipboard 木屑板chisel 凿子choke "扼流,截流,阻塞"choke coil 扼流线圈chopper 斩波器chrome 铬chuck 卡盘CIF(cost insurance and freight) 到岸价cinder concrete 煤渣混凝土circle "周期,圆"circuit 电路circuit breaker "断电器,断路器"circuit diagram 电路图circular pitch 周节circulating pump 循环泵circulation 循环circumferential force 圆周力circumferential speed 圆周速度circumferential velocity 圆周速度CL(center line) 中心线clacking 盖板cladding 装饰clamp 夹clamp ring "压制环,加紧环"clamping jaw 夹钳clamping sleeve 夹紧套桶clamping strap 制动带class of loading 灾荷种类clear depth 净深度clear dimension 净尺寸clear door height 门净高度clear door width 门净宽度clear entrance to the car 轿厢入口净尺寸clear height 净高clear hoistway 井道净尺寸clear width 净宽度clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度clearance top car 轿顶安全高度clearance top counterweight 对重装置顶部安全高度cleated riser 梯级竖板clerance 间隙clevis U型夹client "客户,买主"clip 钳夹clockwise 顺时针的close circuit 闭合电路closed loop 闭环closed position (门)关闭位置closed position monitoring (门)关闭位置检测closed-loop control 闭环控制closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing travel 门关闭运行closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体)CNC(computerized numric control) 计算机数控coast to stop 滑行停车coating 涂层coaxial cable 同轴电缆cock 龙头code "码,符号,规程,规范"code of practice "实施规程,实用规程"code word 代号文字coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数coefficient of friction 摩擦系数coil "线圈,绕组"coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate "栅栏门,折叠式门"collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection "收集,集合"collective control 集中控制collective full automatic operation 全自动集中控制collective operation elevator 集中操作电梯collective selective 集选collective selective control 集选控制collector 集电路collision switch 碰撞开关color 颜色colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column "柱,立柱"comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment "隔板,隔室"compennsating device for hoist ropes 曳引绳补偿装置compensanting/equalizer disk 补偿/补偿器compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent "有资格的,胜任的"competent personnel "有资格的人员,胜任的人员" competitor system 竞争机制component 部件compound wind motor 复励电动机compound wound 复绕comprehensive 综合的comprehensive maintenance contract "综合维修合同,全包维修合同"comprehensive service contract "综合维修合同,全包维修合同"compressing spring 压缩弹簧compression 压缩compression switch 压缩开关compressive stress 压应力compressor 压缩器compulogic system 电脑程序控制系统computer 计算机computer peripheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed "隐蔽的,暗式"concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod "连杆,连接杆"connection 连接connection diagram of controller 控制柜连线图connector "接线柱,连接器"conract specification "合同规定,合同明细表" conract speed "合同速度,额定速度"consecutively departing 依次派出的轿厢console panel "控制柜,控制盘"constant "恒定的,常数"constant HP motor 功率恒定型电机constant speed valve "比例控制阀,调速阀"constant torque motor 力矩恒定型电机construction "安装,施工"construction crane 建筑起重机construction layout drawing 土建图construction platform "安装平台,施工平台" construction site "安装工地,施工工地"consultant "顾问,咨询机构"consumption 消耗contact 触点contact angle 接触角contact brace 触头撑条contact burning 触头烧损contact carrier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger "接触指,滑触头"contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷contact mat 触头垫片contact normally closed 常闭触点contact normally open 常开触点contact pressure 触头压力contact resistance 接触电阻contactless 无触点contactless control 无触点控制contactless control system 无触点控制系统contactless switch 无触点开关contactor 接触器contents 内容conter 计数器continuing travel indicator (轿内)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关contract "合同,契约,承包合同"contract capacity "合同载重量,合同容量"contract load 合同负载contract of indemnity 赔偿合同contract party "合同方,合同当事人"contract work system 合同制度control 控制control amplifier 调节放大器control bus 控制总线control cabinet 控制柜control cable 控制电缆control circuit 控制电路control device for handrail brekage 扶手带断带保护装置control feature 控制特征control gear 控制论control guard for handrail breakage 扶手带断带保护装置control lever 控制杆control panel 控制屏control stand 控制台control station 控制站control switgh 控制开关control system 控制系统control system for elevator 电梯控制系统control technique 控制技术control type 控制形式control valve 控制阀control valve unit (液压)调节阀装置control voltage "控制电压,操作电压"controlled angle 控制角controller 控制柜controller base 控制柜底座controller cabinet 控制柜controller panel 控制屏controller wiring diagram 控制柜电路图controlling circuit 控制电路conuter-clockwise 逆时针方向conventional 常规的conventional lift 普通电梯converter "整流器,转换头"converter panel 换流器盘converter set 换流器组件converter unit 换流装置conveyance of passengers 乘客载运conveyer 输送机conveyer track 输送车轨道cooler 冷却装置cooler air-conditioner 空调制冷cooling 冷却cooling device for semiconductor 半导体冷却装置cooling fan 冷却风扇COP(car operation panel) 轿厢操纵盘copper 铜cord "绳索,芯线"cord drive "绳传动,(厅门)"core 铁心core press 铁心压力core ventilation 铁心通风cork 软木cork packing 软木盘根corner "角,隔"corner post 对角立柱corpus lift 尸体升降机correct phase sequence 正确相序correcting "修正,校正"correcting travel 校准运行correction "校正,校准"corrective maintenance 校正维修。
lock washer(L/W) 斜垫片 lockable 可闭锁的,可锁定的 locker 摇杆,锁紧器 lock-in circuit 自保电路 locking jaw 锁紧爪 locking relay 自锁继电器 locks 门锁装置,联锁装置 log diary 运行日记 logger 记录器 logic analyser 逻辑分析器 logic circuit 逻辑电路 logic diagram 逻辑图 logic element 逻辑元件 logical combination 逻辑结合 long ton 长吨,英制吨 long wait hall call 候梯时间较长的门厅呼梯 long wait landing call 候梯时间较长的层站呼梯 longitudinal 纵向的 Long's lay rope 同向捻(顺捻)钢丝绳loop 环圈 loop circuit 环形电路 loop current 环流 loose bearing 松配轴承 loose fit 动配合 loss 损耗 loss of power 功率损耗 loudness level 响度 louver 气窗 low carbon steel 低碳钢 low cost 低成本的,廉价的 low rise building 低层建筑物 low speed 低速的,慢速的 low speed winding 低速绕组 lower chord 下楔材料 lower cost solution 低成本方案 lower frame 底部框架 lower/upper landing (自动扶梯)下部/上部通道 lowest call reversal(LCR) 最低层呼梯反向 lowest reversal floor 最低反向楼层 low-rise lift group 低层区电梯组群 low-rise zone 低层区 low-speed door 低速门 LS(limit switch) bracket 限位开关支架 LS(limit switch) cam 限位开关碰铁 lubricant 润滑剂 lubricating fitting 润滑装置 lubricating instructions 润滑说明书 lubrication 润滑 lubrication ring 润滑油杯 lubricator 润滑器 lug 线桥 luggage lift 行李电梯 lumen 流明(光通量单位)luminous indicator 发光指示器 Lux 勒克司(照明单位) machinability 切削性machine 曳引机 machine beam 曳引机承重钢梁 machine beam plate 曳引机支撑板machine bed 曳引机座 machine bed inserting mortar 曳引机座(砂浆)灌缝 machine bed plate 机器底板,曳引机底板 machine driving 曳引机 machine earthquake proof stopper 曳引机防震挡止器 machine elevation device 曳引机高度调整装置 machine frame 曳引机架 machine installation 曳引机安装 machine isolation 曳引机隔震machine isolation device 曳引机隔震装置 machine language 机器语言 machine No. plate 曳引机编号牌 machine room 机房 machine room area 机房面积 machine room arrangement 机房布置 machine room depth 机房深度 machine room height 机房高度machine room inspection 机房检修 machine room lower 下机房 machine room of hydraulic lift 液压电梯机房 machine room plan 机房布置图 machine room upper 上机房 machine room width 机房宽度 machine room wiring harness 机房配线束 machine sheave cover 曳引机绳轮罩 machine spacing bed 曳引机高度调整底座 machine sprocket 曳引机链轮 machine supporing steels 曳引机承重钢楔 machine supporting beams 承重梁 machine supporting steelwork 曳引机承重钢结构 machine tools 机床machined 机加工的 machinery 机械 machining 机械加工 machining allowance 加工余量 machining in general 普通机械加工 magnet 磁条 magnet brake 磁力制动器 magnet coil 电磁线圈 magnet lamination 电磁铁芯片 magnet plunger 插棒式电磁 magnet vane 隔磁板 magnetic amplifier 磁放大器 magnetic brake 电磁制动器 magnetic catch 磁闩magnetic charateristic 磁特性 magnetic clutch 磁性离合器 magnetic detector 磁力检查器 magnetic flux 磁通量 magnetic flux density 磁通密度 magnetic leveling switch 磁性离合开关 magnetic noise 电磁噪声 magnetic pole 磁极 magnetic resistance 磁阻magnetic switch 磁感应开关 magnetism 磁性 magnetism pole 磁棒 magnitude 大小,数量,等级 magntic core 磁铁芯 mahogany 红木 main chain 主链条 main circuit 主电路 main circuit breaker 主断路器 main circuit control 主电路控制 main contact 主触点main contactor 主接触器 main drive 主驱动装置 main drive chain 主驱动链 main drive chain guard 主驱动链保护装置 main drive shaft 主驱动轴 main drive sprocket 主驱动链轮 main drive wheel 主驱动装置 main drive wheel 主驱动轮 main floor 基站 main landing 基站 main landing door switch 基站门开关 main lobby 大厅,主厅 main menu 主菜单 main power 主电源 main program 主程序 main reservoir 油箱 main rope 主钢丝绳 main stop 基站 main switch 总开关 main valve 主阀门 main-drive assembly 主驱动总成,主驱动部件 maintenance contract 维修合同 maintenance control 检修控制maintenance cost 维修成本 maintenance fitter 维修保养工 maintenance instruction 维修说明书 maintenance man 维修人员 maintenance operation 维修作业 maintenance-free 免费维修 make contact 触点闭合 maker's name plate 制造商铭牌 making button 动合按钮 male guie rail 雄导轨,带凸榫导轨 malfunction 误动作,失灵,不正常工作mallet 木槌 managanese bronze 锰青铜 mandatory 强制的 manganese 锰 manhole 人孔man-hour coutput 人小时产量 manipulation 利用,操纵 manipulator 操纵器,机械手man-made fiber 人造纤维 manometer 压力计 mansion 大厦 manual brake release 手动松闸装置 manual lowering valve 手动下降阀 manual opened door 手动门 manual opened hoistway door 手动厅门 manual tune 人工调节,手动调节 manual type of control 手动控制 manual wheel 盘车手轮 manualemergency operating device 手动应急操作装置 manually operated down valve 手动下降阀 manualy operated door 手动门manufacture 制造,生产 manufacturer 生产者 manufacturing and sales release 生产和销售许可通知 manufacturing release 生产许可通知 manufacturing tolerance 制造公差maple 枫木 margin 极限,边界,范围 marginal condition 边缘条件 marine elevator 船用电梯 market concept 市场观念 market position 市场地位 market report 市场报告market share 市场占有率 masonry wall 转砌墙 masonry well 砖砌井道 mass 质量,块,团,大量的 mass monent of inertia 惯性矩 mass production 大量生产 master 主任,硕士,主导的,精通的 master PC board 主印数电路板 master station 总站master/slave method 主/从方法,防效方法 mat 垫块,罩面 mat switch 罩面开关matching 匹配 materia overhead 材料管理费 material 材料 material handling 材料搬运material supply planning 材料供应计划 matted design 闷光图案 maximum 最大的maximum capacity 最大容量,最大能力 maximum clear opening 最大净开口maximum load 最大载荷 maximum speed 最高速度 maximum waiting queue 最大候梯乘客量 maximum waiting time 最长候梯时间 mean square 均方 mean value 平均值,有效值〕 mean velocity 平均速度 means 方法,装置 measured load 测定值 measuring instrument 测量仪表 measuring meter 测量计 measuring range 测量范围 measuring unit 计量单位〕 mechanic 钳工 mechanical brake 机械式制动器 mechanical car position indicator 机械式轿厢位置指示器 mechanical door interlock 门机械联锁装置mechanical door safety 机械式门安全装置 mechanical efficiency 机械效率 mechanical lock 机械式锁 mechanical reopening device 机械式重开门装置 mechanical safety shoe 机械式安全触板 mechanical switch 机械开关 mechanism switch 机器开关 mechanized parking garage equitment 机械化停车库设备 medium duty traffic 中级负荷交通medium speed 中速,单层运行最高速 megger 兆欧表,高阻表,摇表 megohm 兆欧姆 melting point 融化点 member 部件 memorandum 备忘录 memory 记忆装置memory address 存储地址 memory location 存储位置 menu 菜单 mercury 汞,水银mercury arc 汞弧 mercury switch 水银开关 mercury vapor rectifier 汞气整流器mercury vapour 水银蒸汽,汞气 mercuryarc rectifier 汞弧整流器 mercury-wetted relay 水银湿润继电器 merit 优点,指标 mesh 网 meshed 网式的 meshed design 网状图案metal 金属 metal section 金属型材 metallic shim 金属垫片 meter 计量器,仪表,米,公尺 meter-in circuit 电路仪表 metering valve 计量阀 method 方式,方法 metric 公制metric graduation 公(米)制刻度 metric ton 公吨 MG(motor generator) 电动机发电机组 MG(motor generator) set 电动机发电机组 mian terminal 大端子 mians 电力网mians current 馈路电流 mians voltage fluctuation 电源电压波动 miantainer 维修工,维修人员 miantenance 维修,保养 miantenance agreement 维修协议 micro limit switch 微动限位开关 microampere 微安培 micro-computer 微型计算机microcontroller 微型控制器 microfarad 微法 microfilm punched card 微缩胶片冲孔卡micro-processor 微处理器,微机 microprodessor opertation control 微处理机操作控制micro-switch 微动开关 microvolt 微伏 middle conductor 中线段 middle speed elevator 中速电梯 midpoint 中间 mid-rise building 中层建筑物,中高度建筑物 mild steel 软(低碳)钢 mileage recorder (电梯)运行次数记录器 mill 铣削,轧钢机(厂)milliampere 毫安培 millimeter 毫米 milling cutter 铣刀 milling machine 铣床 millivolt 毫伏特 mine lift 矿井电梯 mineral cotton 矿物棉 mineral fiber 矿物纤维 mineral wool 矿物毛 minus 负极,负数 minute 分钟 mirror 镜子 mirror finish 镜面抛光,镜面加工mirror finished stainless steel 镜面不锈钢 mirror-inverted 对影像的 miscellaneous 杂项的,其他的 mixing 混合 mode casting mill 铸模车床 mode of supplly 供货方式modem 调制解调器 modern 现代的 modernization 现代化,(电梯)更新改造modernization overlay 全面改造,全面现代化 modification 修改 modifier 调节器modular 组模式,组合式 modular concept 组模化原理 modular escalatot 多坡度(组合式)自动扶梯 modular system 组模系统 modular unit 组模单元 modulation 调制解调器 module (集成电路)组件,继电器,固态继电器 modulus 模数 modulus of elasticity 弹性模数 modulus of longitudinal elasticity 纵向弹性模数 modulus of transverse elasticity 横向弹性模数 moisture 湿度 moisture proof 防潮的 molding 壁板缝压板,模压 molybdenum 钼 moment (力,弯,转)矩 moment of inertia 惯性矩momentary pressure 瞬时的 moniflop 单稳态触发器 monitor 监视,监控,检测monitor panel 梯群监控盘 monitor program 监控程序 monitoring 监视,监控,检测monitoring contact 监控触点 monitoring device 监测装置,监控装置 monkey wrench 活动扳手 mono 单一的 monochrome 单色的 mono-mass safety 单件安全装置monostable circuit 单稳态电路 mon-preformed rope 松散绳 mortuary lift 殡仪馆电梯,太平间电梯 MOS(metal oxide-semiconductor) 金属氧化物半导体 MOS(metal oxide-silicon) 金属氧化物硅 motion 运动 motion control 拖动控制 motion speed 运行速度 motor 电动机,马达 motor base frequency 电机频率 motor base speed 电动机额定速度 motor capacity 电机功率 motor drive unit 电机驱动装置 motor fan 电动机(冷却)风扇 motor field excitation switch 电动机磁场激励开关 motor handle 盘车手轮motor pulley 电机皮带轮 motor rated sped 电动机额定速度 motor shield 电机端罩motor testing stand 电机试验台 motor vehicle lift 汽车电梯 motoring condition 电动状态 moulding 模压,模制零件,制模 mounting bracker 固定架 mounting plate 固定板mouse 鼠,鼠标 movable cam 可动凸轮,可动碰铁 movable car platform 活动轿厢底盘 moving coil motor 动圈式电动机 moving contact 活动触点 moving walk 自动人行道 muffler 消音器 mullti-conductor cable 多线电缆 multi-core cable 多芯电缆 multi-funtion 多功能的 multi-group 多组群(电梯) multi-leaf door 多扇门 multi-leaf sliding door 多扇滑动门 multi-panel sliding door 多扇滑动门 multiple 多重的 multiple elevator hoistway 多电梯井道 multiple floor flight time 多层运行时间 multiple leaf door 多扇门 multiple roping(multi-roping) 多线悬挂的 multiple tenancy building 多个承用者大楼 "multiple thread wor," 多螺纹蜗杆 multiple well 多梯井道 multiple wire plug connection 多线插接 multiple-floor run 多层运行时间 multiplex down-collective automatic operation 多层下集选全自动控制 multiplying pulley 倍增滑轮 multi-plywood 多层胶合板 multipoint connector strip(pcb) 插式接头板(印刷电路板)multi-program 多程序系统 multi-roped lift 多绳悬挂电梯 multi-section door 多扇门multi-speed driving 多速驱动系统 multi-speed starting 多速起动 multi-stage jack 多段式液压升降装置 multi-stage ram 多段式柱塞 multi-start worm 多头蜗杆 multi-storey flat 多层公寓 multi-story building 多层建筑物 multi-stpreu apartment house 多层公寓multi-use 多用途的 multi-voltage control 多极电压控制 multi-way stitch 多路开关multi-wire cable 多线电缆 munsell color system 蒙塞尔色调 mutation 转变,更换N.C.(normal closed ) contact 常闭触点 N.O.(normal open) contact 常开触点 nameplate 铭牌 nameplate current 铭牌电流,额定电流 NAND gate 非与门 narrow door jamb 小门套,窄门套 national codes 国家标准 national regulation 国家规定 natural fiber 天然纤维 natural frequency 固有频率 natural lighting 自然照明 natural period 固有周期natural ventilation 自然通风 nbuilder's work 土建工程 neck of axle 轴颈 needle 针needle bearing 滚针轴承 needle cage 针罩 needle point pliers 尖嘴钳 negative 负电negligible 可忽略的 neon glow 氖辉光管 neon lamp 霓虹灯 neoprene 合成橡胶 net 网络,净值,有效的 net car floor area 轿厢地板净面积 net section 有效截面 neuron network 神经网络 neutral conductor 中性线 neutral earthing 中性接地 neutral grounding 中性接地 neutral point 中性点 neutral position 中性位置 newel 中性,楼梯扶栏柱 newel stand 中柱台 nib 牛腿,凸边 nickel 镍 nickel chromium molybdenum steel 镍铬钼钢 nickel molybdenum steel 镍钼钢 nickel steel 镍钢 night traffic 夜间交通no load test 空载实验 noise 噪声 noise insulation 隔音 noise level 噪声电平,干扰电平 noise proof 隔音 noise protction 噪声防护 noise reduced 减噪声的 noise suppression 消音的 no-load current 空载电流 no-load operation 空载操作 no-load running No. of poles 空载运行极对数 nomenclature 术语,命名 nominal 标定的 nominal diameter 标称直径 nominal dimension 公称尺寸 nominal spedd of up motion 上行额定速度nominal speed of down motion 下行额定速度 nominal tensile strength 标称抗拉强度nominal torque 额定扭矩 nominal-data 额定数据 non-combustible 不易燃的 non-combustible material 不可燃材料 non-contact electronic door safety sensor 不接触电子传感式门安全装置 none return valve 单向阀 non-ferrous 非铁的 non-flammable 不可燃的 non-magnetic shield 隔磁屏 non-metallic 非金属的 non-reversing device 防逆转装置,防反向装置 non-selective collective automatic operation 非集选自动控制 non-stop 无停站 non-stop button 直驶按钮 non-stop switch 直驶开关 non-volatile(NV) memory 非易失性存储器 noon peak 午间交通高峰 noon traffic mode 午间交通 NOR circuit 非或电路 NOR gate 非或门 normal bend coupling 普通管接头联轴器 normal illumination 正常照明 normal limit switch 限位开关 normal position 正常位置 normal terminal stopping switch 终端常位停车开关 normal travel 正常运行 normalizing 正常化 normally closed (N/C) 常闭的 normally opened (N/O) 常开的 nose line 凸出线 nose of comb 梳齿端 nosing 牛腿 NOT circuit 非电路 NOT gate 非门 notch V型槽,V凹口 note 加注,说明 notice for use 使用须知 nudging 强迫关门 nuisance 捣乱 number of passenger 乘客人数 number of revolutions 转数 number of segment 换向片数number of slots 电机槽数 number of stops 停站数 number of turns 绕线匝数 numbering of elevator 电梯编号 nut 螺帽,螺母 nylon 尼龙 nylon lining 尼龙衬套 nylon tube 尼龙管 oak 橡木 object 物体 observation cab 观光轿厢 observation lift 观光电梯observatory lift 观光电梯 occupancy 占用,居住 occupant 占用者,居住者 occupants of building 大楼居住者,大楼住户 off peak 非高峰的,峰值外的 off position 断开位置 office building 办公大楼 off-peak traffic 非高峰交通状态 ohmmeter 欧姆计 oil 油oil brake 油压制动器 oil buffer 油压缓冲器,耗能型缓冲器 oil buffer switch 油压缓冲器开关 oil can 油壶 oil collector 集油器 oil cooler 油冷却器 oil deflector 挡油圈 oil dish 积油盘 oil drip pan 接油盘 oil filler pipe 充油管 oil film 油膜 oil filter 滤油器 oil gauge 油量表 oil immersed transformer 油浸式变压器 oil leakage 漏油 oil level 油位oil level gauge 油标,油位计 oil level indicator 油位指示器 oil pan 油盘 oil piping 油管 oil quench 油淬火 oil receiver 油盘 oil reservoir 油池 oil ring 油环 oil seal 油封 oil spray 油雾 oil sump gasket 油槽垫圈 oil tank 油箱 oil waste box 油渣盒 oil wick 油绳oil wiper ring 挡油环 oilier 给油器 oil-immersed 浸油的 oilless bearing 无油式轴承oil-proof 耐油的 oil-tight 油封 on inquiry 询问,询价 on-board delay 登梯延时,登梯后的等候时间 on-board delay in passenger seconds 登梯及等候时间 on-call control 呼梯控制 one floor run 单层运行 one hour rating 小时定额 one stage ram 一段式柱塞one way automatic leveling device 单向自动平层装置 one way restrictor 单向节流阀(液压梯) one-to-one rope 1:1 绕绳比 one-to-two rope 1:2 绕绳比 on-line 在线的,联机的 onlocking zone 开锁区域 on-site assistance 现场帮助 opal 乳白的 opaque 不透明的 opaque balustrade 不透明扶栏 open air type elevator 露天电梯 open circuit 断路open loop 开环控制 open type elevator 敞开式电梯 open-close switch 开关操纵器opened-type motor 敞开式电动机 open-end wrench 开口扳手 open-hearth steel 平炉钢opening angle 张角,开启角 opening direction 开启方向 operable 可操作的 operate 操作 operating button 操作按钮 operating cam 操作碰头 operating device 操作装置operating element 操作元件 operating instructions 操作说明书,使用说明书 operating magnet 操作磁铁 operating panel 操作盘 operating pressure 操作压力 operating range 操作范围,使用范围 operating voltage 操作电压,工作电压 operation 操作,运转,控制 operation panel 操纵箱,操纵盘 operation system 操作系统,操作方式operational amplifier 运算放大器 operational brake 操作制动器 operational reliability 操作可靠性 operative section 操作部分 operator 操作碰铁,司机 opposed access door两面开门 opposing arrangement 对面布置 opposing automatic doors 贯通式自动门opposite car entrance 贯通式轿厢出入口 opposite door 贯通式门 opposite entrance 贯通式出入门 opsition dependent 按位置 opsition detector 位置检查器 opsition deviation 位置偏差 optical 光学的 optical fiber 光导纤维 optical fiber cable 光缆,光导纤维电缆 optical indicator 发光指示器 optical signal 发光信号 optical-fiber communication 光导纤维通讯 optional 可选择的 optional specification supervision 可选规格管理 opto-coupler 光电耦合 optoelectronic 光电耦合 OR circuit 或电路 OR gate 或门 order 订单,订货单,次序 order processing 合同(订单)处理 ordering documentation 订货文件 ordering instruction 订货说明书 ordinary lay 普通绳股 ordinary lay rope 普通捻股钢丝绳 ordinary lift 一般用电梯 orifice 节流孔,阻尼孔 original 原装的,原件,原图 original package 原包装 O-ring O型圈 ornamental-patterned surface 装饰花纹表面 oscillator 示波器 oscillograph 示波器 oscilloscope 示波器 oscillosynchroscope 同步示波器 out door use escalator 户外自动扶梯 out of balance load 不均衡负载 out of phase 相移 out of phase 180°相移180° out of phase 90°相移90° out of service 故障,停止运行 out of stock 无现货 outer deck 外侧盖板 outer ledge 外侧边缘 outer ledge bracket 外侧架支架 outer panel 外侧板 outer pipe 出口管 outer sheathing 外套 outlet 插座,引线,出口 outline 轮廓,外形 outling of truss 框架外形 output 输出 output current 输出电流 output signal 输出信号 output torque 输出扭矩 output voltage 输出电压 outside 外面,外边 outside diameter 外径 oval 椭圆形 over balance 超平衡 over driven worm gear 蜗杆在上方的蜗轮蜗杆传动 over heating 过热 over power 过负载over run 超程 over sling 上吊架 over slung type 上悬吊式 over speed switch 超速开关overall cost 总成本,总费用 overcurrent 过电流 overcurrent relay 过流继电器overcurrent release 过电流释放 overcurrent vreaker 过流断路器 overhang 悬臂式,外伸的 overhang traction sheave 悬臂式曳引轮 overhaul 大修 overhead 顶层空间,顶部overhead beam 顶楔 overhead height 顶层高度,顶部高度 overhead machine 顶置曳引机 overhead pulley 顶部轮 overhead sheave 顶部绳轮 overhead structure 顶部构件overhead(O/H) 顶房上置 overhoisting limit switch 井道上部限位开关 overlap 重叠overlay (墙壁等)饰面 overload 超载 overload buzzer 超载蜂鸣器 overload control 超载控制 overload device 超载装置 overload indicator 超载装置 overload lamp 超载灯overload test 超载试验 overload warning 超载报警 overload weighting microswitch 超载微动开关 overrun 越程 overshoot 过冲,速度调节过量 oversize 大号,超大号oversize reamer bolt 大号螺栓 overslung car 上方悬臂轿厢 overspeed 超速 overspeed governor 限速器 overspeed governor switch 超速保护装置 overtravel 越层 overturn moment 倾倒力矩 overturn-proof 房倾倒装置 overweight 超重 over-wind protection switch 防过卷开关 owner 物主,所有者 oxidate 氧化 p.c. motherboard 印刷电路母板package part 零件组合 packaging material 包装材料 packed landing bolt 门厅用配套螺栓 packing 包装 packing charge 包装费用 packing cost 包装成本 packing ring 密封环pad 衬垫,垫片 paddle fan 叶片式通风扇 paging service 传呼服务 paint 油漆 painting 涂漆,涂装 pale 踏板 pallet type moving walking 平板式自动扶梯 pallets 踏板 pan 盘panel 板,扇,屏 panel door 板式门 panorama lift 观光电梯 panoramic lift 观光电梯pantagraph 壁杆 pantagraph type hydraulic elevator 壁杆式液压梯 paraffin 煤油,石蜡parallel 并联 parallel circuit 并联电路 parallel continuous arrangement 并列设置parallel key 平键 parallel lay rope 平行捻钢丝绳 parameter 参数 parapet 防护栏杆parasitic signal 寄生信号 parking 驻停 parking car 驻停轿厢 parking device 停靠装置parking floor 驻停楼层 parking landing 驻停层站 parking signal light 驻停信号灯parking switch 驻停开关 parking zone 驻停区 part 零件 part for jamb and sill installation 门套和门坎安装用零件 partial load 部分载荷 partial view 局部视图partition 分隔,隔板 parts for closer installation 关门机安装用零件 parts layout 零件配置图 parts list 零件清单 pass button 直驶按钮,不停按钮 pass switch 不停开关,直驶开关 passage way 通道 passenger 乘客 passenger access time 乘客登梯时间passenger arrival rate 乘客到站率 passenger car 载客轿厢 passenger carried per minute 每分钟载运乘客人数 passenger conveyor 自动人行道 passenger exit time 乘客出梯时间 passenger journey time 乘客乘梯时间 passenger lift 乘客电梯 passenger loading time 乘客进入电梯时间 passenger transfer time 乘客进出电梯时间 passenger transit time 乘客转乘电梯时间 passenger transported per minute 每分钟载运乘客人数passenger unloading time 乘客走出电梯时间 passenger waiting time 乘客候梯时间passenger way 走道 passenger/freight elevator 客货两用电梯 passenger-and-freight elevator 客货两用电梯 passenger-goods lift 客货电梯 passing chime 到站钟 passive mode 被动模式 password 通行令,口令 patent 专利 patenting 线材(拉后退火)paternoster 链斗式升降机 pattern 图形 pavement lift 自动人行道 pawl 棘爪 PC board 印刷电路板 PCB (printed circuit board) 印刷电路板 PCB assembly frame 印刷电路板组装架 PCB bay 印刷电路板抽屉盒 PCB connection strip 印刷电路板插接条 PCB edge connector 印刷电路板边缘插接器 PCB plug-in check 印刷电路板插接通电检查PCB rack 印刷电路板插架 peak current 峰值电流 peak load 高峰负载 peak service 高峰交通服务 peak value 峰值 pedestal bearing 托架轴承 pension fund 退休基金,养老基金 penthouse 楼顶机房 pentode 五极管 perambulator 手推车 percenage 百分比percentage load 负载百分比 performance 性能 performance characteristic 性能特征performance curve 性能曲线 performance guaranteed maintenance 性能保证维修performance index 性能指标 performance test 性能试验 performed rope 预成型钢丝绳period of guarantee 担保期限 periodic maintenance 定期维修保养 periodic test 周期性试验,定期试验 periodical examination and test 定期检查和试验 periodical inspection 定期检查 peripheral 圆周的 peripheral force 圆周力,切线力 peripheral speed 圆周速度 periphery 圆周,圆柱体表面 permanent 永久 permanent magnet 永久性磁铁permeability 磁导率,渗透性 permissible deviation 允差 permissible stress 许用应力permitted stress 许用应力 personal code 个人电码 petroleum 石油 PG (pulse generator) 脉冲发生器,编码器 PG constant 编码器解像度,编码器常数 PG size 编码器解像度,编码器常数 phase 相位 phase advance 相移超前 phase angle 相位角 phase angle control 相位角控制 phase difference 相位差 phase failure 断相 phase failure relay 断相保护继电器 phase lagging 相移延迟 phase lead 相移超前 phase loss 断相 phase monitoring relay 相位监控继电器 phase reversal 反相,相序逆转 phase reversal relay 换相继电器 phase reversed 反相 phase shifting 相移的,移相的 phone connector (通讯线)插头 phosphorus 含磷的 photo detector 光监测装置 photo eye 光电监测器photo switch 光电管开关 photocell switch 光电管开关 photo-coupler 光电耦合器photo-diode 光电二极管 photo-electric cell 光电管 photo-electric device 光电管装置photo-electric passenger detector 光电乘客监测器 photo-electric protection 光电保护photo-electric safety device 光电保护装置 photo-electric switch 光电开关 pick-up (继电器)吸合,得到信号 picture plane display 画面显示 PID (proportional-integral-differential) 比例-积分-微分 piece rate 计件单价 piece wages 计件工资 piercing 冲孔 pillow block 架座 pilot light 指示灯 pilot production 试生产 pilot valve 导向阀 pin 销钉 pin adaptor 插头转接器 pincer 钳子 pine 松木 pinion 小齿轮,齿节 pipe 管子pipe bend 弯管 pipe clamp 管箍 pipe connection 导管连接 pipe fitting 管道配件 pipe rapture valve 管道破裂保险阀 pipe system 管道系统 pipe threading 管螺纹 pipeline 管道 piping 配管,管路 piston 活塞,柱塞 piston type cylinder 柱塞式油缸 pit 底坑 pit access door 底坑检修门 pit access ladder 底坑出入爬梯 pit depth 底坑深度 pit ladder 底坑爬梯 pit lamp 底坑灯 pit protection railing 底坑保护栅栏 pit ptotection gred 底坑护栏 pit safe plate 底坑安全板 pit screen 底坑防护网 pit stop switch 底坑停止开关 pit switch 底坑开关 pit tanking 底坑防水层 pitch 螺距 pitch circle 齿节 pitch diameter 节径 pitch line 节距 pitch of teeth 齿节距 pivot pin 中心销钉 pivot point 支点 pivoted guuide shoe 活动导靴 plain bearing 滑动轴承 plane 刨,刨平 planetary machine 行星齿轮机器 planing machine 刨床 plank (轿厢架)底楔 plastic foil 塑料薄膜 plastic materials 塑料材料 plastics 塑料 plate 板 plate counterweight 板式对重 plate glass 平板玻璃 plate spring 板簧 plate threshold 轿厢地坎 plated design 镀金图案 platform 轿厢底,轿底 platform frame (轿厢)底盘架 platform guard 轿厢站台护板 platform side brace 轿厢底侧拉条 platform sill 轿厢地坎 plating 电镀 PLC(programable logic controller) 可编程序控制器 PLD(programmable logic device) 可编程序逻辑器件 pliers 虎钳 pllug socket 插座 plug 插头转接器 plug connection 插塞连接 plug pin 插脚,插销 plug receptacle 插座 plugability 可插接性 plug-in module 插接式模块 plug-in type 插接式 plug-in unit 插接元件 plumb 铅垂侧直,铅垂 plumb bob 铅垂重物,铅垂plumb line 铅垂线 plunger 柱塞,插棒铁芯 plunger end-plate 柱塞端板 plunger head 柱塞顶部 plunger head sheave 柱塞顶部轮 plunger limit switch 柱塞限位开关 plunger return 柱塞复位 plunger runby 柱塞越程 plunger sheave 柱塞滑轮 plunger stopper 柱塞挡止器,柱塞防脱装置 plunger stroke 柱塞行程 plunger type cylinder 柱塞式液压缸 plus 加,正极 plyphase 多相 plywood 三合板,胶合板 pneumatic 气动的pneumatic door operator 气动开门机 point fo common connection (PCC) 普通接点pointer 指针 polarity 极性 pole 电极 pole coil 电极线圈 pole core 电极芯子 pole piece 极靴 pole shader 极帽 pole-changing 变换极性的 pole-piece lamination 极靴铁芯片polish 抛光 population 人口,人数 position 位置 position actual value 位置实际值position control 位置控制 position control loop 位置控制回路 position control system 位置控制系统 position controller 位置控制器 position feed-back loop 位置反馈回路position indicator 位置指示灯 position indicator of adjacent car 邻梯指层灯 position reference value 位置参照值 position reference value generator 位置参照值发生器position regulation 位置调节 position regulator 位置调节器 position scanner 位置扫描器 position sensor 位置传感器 position-dependent slowdown 按位置减速 positioningtrip 定位运行 positive 正电 positive connection 刚性连接 positive drive 强制驱动positive drive service lift 强制驱动杂物梯 positive operation 强制操作 post 柱 potential 电位,电势 potentiometer 电位计,电位器 pound 磅 power 功率,电源 power absorption 能量吸收 power amplification 功率放大 power amplifier 功率放大器 power consumption 功率消耗,电力消耗 power contactor 电源接触器 power converter 变流器 power current circuit 动力电路 power dissipation 功率消耗,电力消耗 power distribution panel 配电盘 power door 自动门 power door operation 电动门 power dumbwaiter 电动杂物梯 power factor 功率因素 power failure 停电,断电 power failure emergency operation 停电应急操作 power failure emergency service 停电应急服务 power input 功率输入 power loss 功率损失 power operated door 自动门 power operated truck 机动货车 power output 功率输出 power pack 电源装置 power range 功率范围 power source 电源 power supply 电源 power supply fluctuation 电源波动power supply line 供电线路 power supply unit 供电装置 power unit 电源装置 power up 通电,上电 powerwalk 自动人行道 PPR (pulse per revolution) 每转脉冲数,脉冲/转pre-announcing direction arrow 预告方向箭头 pre-assemble 预装置 precast concrete 预制混凝土 precautionary measure 安全措施 precondition 先决条件 pre-delivery 提前发货 predetermined landing 预定基站 pre-drill 预钻孔 preduction capacity 生产能力prefabricated 预制的 prefabricated concrete 预制混凝土 preference 优先权 preferential 优先的 preferential floor 优先楼层 preferential floor service 优先楼层服务 preferential landing 优先层站 preferential service 优先服务 preferred number 优选数字 pre-formed groove 预制槽 preliminary construction work 土建准备工作 preliminary standard 基础标准 preload 预负荷 pre-locking 预锁定 pre-locking control 预锁定控制 pre-opening 提前开门 pre-opening of door 提前开门 preparatory program 预编程序 preprinted 预先印刷的 prerequisite 前提 pre-select 预选 pre-selection 预选装置 preset 预调,预设定preset time delay 预调延时 preset value 预调值 press working 预压加工 pressing 冲压,加压 press-to-talk system 按钮对讲系统 pressure 压力 pressure gage 压力表,压力计 pressure indicator 压力表 pressure project 样板项目,样板工程 pressure relief valve 压力安全阀 pressure-reducing valve 减压阀 pretension 预应力,预控力 pre-torque 预加力矩 preventative maintenance 预防性维修 preventive maintenance 预防性维修 pre-view 预验,试映 pre-warning 预警,预告 price calculation 价格决算 price increase 提价 price list 价格表 price quotation 报价 price reduction 减价 pricing 计价primary circuit 原电路,一次电路 primary coil 一次线圈 primary fireman's operation 主消防操作 primary machine room 主机房 primary position transmitter (PPT) 第一位置传感器 primary resistor 主电阻,定子电阻 primary wave sensor 地震纵波传感器primary winding 初级绕组 prime cost 原价 prime finish 底漆面层 primer 底漆 priming coated 上底漆 principle 原则,原理 print 印刷 print out 打印出 printed circuit 印刷电路 printed circuit diagram 印刷电路图 printed circuit pattern 印刷电路图形 printer 打印机 priority 优先性 priority floor 优先楼层 priority recall 优先召呼指令 priority travel control 优先运行控制 private accommodation 私人住宅 private code 私用电码,密码private lift 私用电梯 private residence elevator/lift 私宅电梯 probability 概率 probable number of stops 可能停站数 probable stops 可能停站 procedure 程序 process 工艺过。
电梯行业专用英语Document serial number【NL89WT-NY98YT-NC8CB-NNUUT-NUT108】电梯LIFT;ELEVATOR乘客电梯PASSENGERLIFT载货电梯GOODSLIFT;FREIGHTLIFT客货电梯PASSENGER-GOODSLIFT病床电梯;医用电梯BEDLIFT住宅电梯RESIDENTIALLIFT杂物电梯DUMBWAITERLIFT;SERVICELIFT船用电梯LIFTONSHIPS观光电梯PANORAMICLIFT;OBSERTIONLIFT汽车电梯MOTORVEHICLELLIFT;AUTOMBILELIFT液压电梯HYRAULICLIFT平层准确度过LEVELINGACCURACY电梯额定速度RATEDSPEEDOFLIFT检修速度INSPECTIONSPEED额定载重量RATEDLOAD;RATEDCAPACITY电梯提升高度TRAVELINGHEIGHTOFLIFT;LIFTINGHEIGHTOFLIFT机房高度MACHINEROOMHEIGHT机房宽度MACHINEROOMHEIGHT机房宽度MACHINEROOMDEPTH机房面积MACHINEROOMAREA辅助机房SECONDARYMACHINEROOM;隔层SECONDARYFLOOR滑轮间隔PULLEYROOM层站台票LANDING层站入口LANDINGENTRANCE基站MAINLANDING;MAINFLOOR;HOMELANDING预定基站PREDETERMINEDLANDING底层端站BOTTOMTERMINALLANDING顶层端站TOPTERMINALLANDING层间距离FLOORTOFLOORDISTANCE;INTERFLOORDISTANCE 井道WELL;SHAFT;HOISTWAY单梯井道SINGLEWELL多梯井道MULTIPLEWELL;COMMONWELL井道壁WELLENCLOSURE;SHAFTWELL井道宽度WELLWIDTH;SHAFTWIDTH井道深度WELLDEPTH;SHAFTDEPTH底坑PIT底坑深度PITDEPTH顶层高度HEADROOMHEIGHT;HEIGHTABOVETHEHIGHESTLEVELSERVED;TOPHEIGHT 井道内牛腿;加腋梁HAUNCHEDBEAM围井TRUNK围井出口HATCH开锁区域UNLOCKINGZONE平层LEVELING平层区LEVELINGZONE开门宽度DOOROPENINGWIDTH轿厢入口CARENTRANCE轿厢入口净尺寸CLEARENTRANCETOTHECAR轿厢宽度CARWIDTH轿厢深度CARDEPTH轿厢高度CARHEIGHT电梯司机LIFTATTENDANT乘客人数NUMBEROFPASSENGER油压缓冲器工作行程WORKINGSTROKEOFOILBUFFER弹簧缓冲器工作行程WORKINGSTROKEOFSRINGBUFFER 轿底间隙BOTTOMCLEANCESFORCAR轿顶间隙TOPCLEARANCESFORCOUNTERWEIGHT对重装置顶部间隙TOPCLEARANCESFORCOUNTERXEIGHT 对接操作规程DOCKINGOPERATION隔层停*操作SKIP-STOPOPERATION检修操作规程INSPECTIONOPERATION电梯拽引型式TRACTIONTYPESOFLIFT电梯拽引机绳拽引HOISTROPESRATIOOFLIFT消防服务FIREMANSERVICE独立操作INDEPENDENTOPERATION缓冲器BUFFER油压缓冲器(耗能型缓冲器)HYDRAULICBUFFER;OILBUFFER 弹簧缓冲器;蓄能型缓冲器具SPRINGBUFFER减振器具VIBRATINGABSORBER轿厢CARLIFTCAR轿厢底;轿底CARPLATRORM;PLATFORM轿厢壁;轿壁CARENCLOSURES;CARWALLS轿车厢顶;轿顶CARROOR轿厢装饰顶CARHANDRAIL轿厢扶手CARHANDRAIL轿顶防护栏杆CARPROTECTIONBALUSTADE轿厢架;轿架CARFRAME检修门DOOROPERATOR检修门ACCESSDOOR手动门MANUALLYOPERATEDDOOR自动门POWEROPERATEDDOOR层门;厅门LANDINGDOOR;SHAFTDOOR;HALLDOOR 防火层门;防火门RIER-PROOFDOOR轿厢门;轿门CARDOOR安全触板SAFETYEDGESFORDOOR铰链门;外敞门HINGEDDOOR栅栏门COLLAPSIBLEDOOR水平滑动门HORIZONTALLYSLIDINGDOOR中分门CENTEROPENINGDOOR旁开门TWO-SPEEDSLIDINGDOOR双折门TWO-PANELSLIDINGDOOR双速门TWOSPEEDDOOR左开门LEFTHANDTWOSPEEDSLIDINGDOOR右开门RIGHTHANDTWOSPEEDSLIDINGDOOR垂直滑动门VERTICALLYSLIDINGDOOR垂直中分门BI-PARTINGDOOR拽引绳补偿装置COMPENSATINGDEVICEFORHOISTROPES补偿绳装置COMPENSATINGROPEDEVICE补偿绳防跳装置ANTI-REBOUNDOFCOMPENSATIONROPEDEVICE 地坎SILL轿厢地坎CARSILLS;PLATETHRESHOLDELEVATOR层门地坎LANDINGSILLS;SILLELEVATORENTEANCE轿顶检修装置INSPECTIONDEVICEONTOPOFTHECAR轿顶照明装置CARTOPLIGHT底坑检修照明装置LIGHTDEVICEOFPITINSPECTION轿厢内指层灯;轿厢位置指示CARPOSITIONINDICATOR层门门套LANDINGDOORJAMB层门指示灯LANDINGINDICATOR;HALLPOSITIONINDICATOR 层门方向指示灯LANDINGDIRECTIONINDICATOR控制屏CONTROLPANEL控制柜CONTROLCABINET;CONTROLLER操纵箱OPERATIONPANEL操纵盘CAROPERATIONPANEL 警铃按钮ALARMBUTTON。
电梯专业英语词汇abbreviation 缩语abnormal "不正常的,反常的"abnormality monitor ing 异常监听abrasion 磨损abrasion resistant 耐磨性abrasive cloth 砂布absorb 吸收absorber 减振器AC drive 交流拖动AC feedback control 交流反馈控制AC motor 交流电机AC servo 交流伺服AC servo motor 交流伺服电机AC single speed 交流单速AC two speed 交流双速AC two speed motor 交流双速电动机AC variale speed 交流调速AC(alternating current) 交流电acanning cycle 扫描周期,扫描循环acceleration control system 加速度控制系统acceleration(accel)rate 加速器accelerator 加速器acceptance of lift 电梯验收acceptance period 验收阶段acceptance test 验收试验acceptanec certificate 验收证书access door 检修门access forbidden 禁止入内access lift 通道电梯access security 通道防卫access switch "通道开关,维修用开关"access way 进出通道accessibility "可通达性,接近的,难易程度"accessible 允许进入accessible space 允许进入的场地accessory "配件,附件"accident 事故accident insurance 事故保险accident prevention 事故预防accidental contact 触电accidental oper ation 误操作accordion door 折叠门accumulation 累积accumulator 蓄电池AC-GL machine 交流无齿曳引机acoustic "听觉的,声音的"acrew die 板牙activate "启动,触发"active mode 主动模式actual condition "实际状况,实际条件"actual load 实际载荷actual state 实际状况actual value 实际值actuate "开动,操作,激励"actuating linkege 操作连杆actuating magnet 操作磁铁actuation time 动作时间actuator "操纵机构,激励器,螺线管"actuator bracket 调节器支架actuator plate 调节板ACVF drive 交流调频拖动ACVF system 交流调频系统ACVF(AC varible frequency) 交流调速ACVV dirve 交流调压拖动ACVV system 交流调压系统ACVV(AC var ible voltage) 交流调压adaptation "适应,匹配"adapter PCB 选通脉冲印刷电路板adapter(adapator) 适配器adapting 选配adaptive contr ol system 自适应能力控制系统addendum "齿顶高,附录"addendum circle 外圆adding working draw ing 附加加工图addition "附加物,加法"additional mater ials 附加材料address 地址adhesion "胶,粘合胶"adhesion protective oil 防粘油adhesive foil 胶粘薄膜adhesive tape 胶带adjacent 邻近的adjacent car "相邻轿厢,相邻电梯"adjacent entr ance 相邻出入口adjusment 调试adjustable condensor 可变电容器adjustable resistance 可调电阻adjustable spanner 可调扳手adjustable speed electr ic drive 调速电力拖动adjustable wrench "活动扳手,可调扳手"adjusting screw 调节螺丝adjustor 调试员administation over jhead rate 管理费用标准administration cost 管理成本administration expenses 管理费用advance door opening 提前开门advance payment 预付款advanced "提前的,先进的"advanced carriage 超前拖板(选层器)advancing position reference value 超前位置参考值aerial cableway "空中缆车,架空索道"aerial ropeway "空中缆车,架空索道"aerial tramway "空中缆车,架空索道"aesthetic 美观after sales service 售后服务agency 代理agenda 议程air cord (门机用)航空钢丝绳air purifier 空气滤清剂air ventilator 通风管air-bleed 空气分泄器airborne noise 空气传播噪声air-condition 空调air-gap 气隙alarm 警报alarm bell 警铃alarm button 警铃按钮alarm buzzer 警报蜂鸣器alarm circuit 警报电路alarm system 警报系统ALC(autoclaved light-weight concrete) 蒸压轻质混凝土alcove arrangement 电梯U型排列法algor ithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignment gauge 校正量规alkali 碱all-computer-controlled 计算机全控的allocation "分配,分派"allocation of landing call 层站呼梯指令分配allow ance "允用误差,加工余量"allow ble stress for temporary load 允许暂时应力值alloy 合金alloy steel 合金钢alteration 改进alternate floor 隔层alumina 氧化铝aluminum 铝aluminum alloy 铝合金aluminum bronze 铝青铜aluminum cladding 铝制包层alumite 防蚀铝alundum 氧化铝ambient 环境的ambient noise 环境噪音ambient temperature 环境温度ammeter 安培计ammonia 氨amperage 电流强度ampere 安培amplification 放大amplification stage 放大等级amplifier 放大器amplifying tube 放大管amplitude 幅度analog adder 模拟加法器analog computer 模拟计算机analog speed card 模拟曲线板analog-digital converter 模拟-数字转换器analogue(analog) 模拟analysis 分析analysis mode 分析模拟anchor bolt 地脚螺栓anchorage "锚具,锚定"angle bar 角钢angle guide 角铁导轨angle iron 角铁angle iron fr ame 角铁框架angle of contact 接触角angle of deflection 导向角angle of inclination 倾斜角angle of lead 导程角angle of traction 曳引机包角angle of wrap 包角angle steel 角钢angular contact ball bearing 向心推力球轴承angular contact bear ing 角面接触滚动轴承angular gear 斜齿轮angular retardationg 角减速度angular velocity 角速度anneal 退火annealing 退火annual inspection 年检annual report 年度报告annunciator "报音器,声音合成器"anode 阳极anodize 氧极氧化ANSI(America Nationa Standard Instirute) 美国国家标准协会anti-clockwise 逆时钟方向anti-corrosive paint 防腐蚀漆anti-creep 防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰anti-nuisance device 防捣乱装置anti-phase braking 反向制动anti-phase current 反相电流anti-rebound of compensation rope device 补偿绳防跳装置anti-residual 防剩磁anti-resonance 抗谐振anti-reversion device 防反转装置anti-rust 防锈anti-stall 防空转anti-vibralion pad 防震垫APM(automatic people mover) 自动人员运输机apparen pow er 视在功率apparent output 视在输出applicant 申请人application 申请application guide 应用指南aprons 裙板arbour "轴,杆"arc chamber 电弧隔离室arc protection 防电弧arc quenching 熄焊弧arc shield 电弧屏蔽arc suppressor 灭焊器architect 设计单位architecture 建筑学architrave 门框area 面积arm "臂,支路"armature 电驱armature coil 电驱线圈armature current 电驱电流armature lamination 电驱铁芯片armature shaft 电驱轴armature spider 星形轮armature w inding 电驱绕组armoured 蛇皮管的armoured cable 蛇皮管电缆armoured conduit 导线管arrangement 布置arrival bell 到站铃arrival buzer 到站蜂鸣器arrival floor 到达楼层arrival gong 到站钟arrival rate 到站率article of consumption 消耗品artificial intelligence 人工智能artistic 工艺artistic face 工艺表面asbestos packing 石棉盘根ascending 上升ASIC(application specific integrated circuit) 专用集成电路assemble 装配assembler language 汇编语言assembly of hinge 铰链组装assign 分配astragal 装饰镶条atmospher ic influence 大气影响attachment 附件attendant control 有司机控制attendant control compartment 有司机控制盒attendant operation 有司机操作audible signal 音响信号audio tape r ecording 磁带录音authority "当局,核准部门"authority of lift acceptance 电梯验收部门authorized "授权的,核准的"authorized user 核准使用者auto-adaptation 自适用AutoC AD 自动计算机辅助设计autographic recoder 自动记录仪automatic 自动的automatic allocator 自动分派器automatic by-pass 自动直驶automatic center opening sliding door 自动中分式滑动门automatic closer 自动关闭门automatic dispatch 自动调度automatic door 自动门automatic homing 自动回基层automatic landing 自动停站automatic landing system by spare battery 靠备用蓄电池的自动停站设备automatic leveling 自动平层automatic lubr icator 自动润滑装置automatic parking garage 自动停车库automatic parking system 自动停车系统automatic relevelling 自动平层校正automatic rescue device 应急救助装置automatic return 自动返回automatic telescopic center opening sliding door 自动中分式折叠滑动门automatic telescopic sliding door 自动折叠式滑动门automobile lift 汽车电梯autowalk 自动人行道auxiliary apparatus 辅助装置auxiliary brake 辅助制动器auxiliary cicuit 辅助电路auxiliary contact 辅助触点auxiliary drive 辅助驱动auxiliary lock 辅助锁auxiliary mater ials 辅助量auxiliary value 辅助材料auxiliary winding 辅助绕组available area 有效面积average 平均average car load 平均轿厢负载average dispatching interval 平均调度间隔时间average interval 平均调度间隔时间average passenger waiting time 平均乘客侯梯时间average response time 平均应答时间average waiting quest 平均乘客量average waiting time 平均乘客侯梯时间axial flow fan 轴流式风扇axis 轴线axle 轴babbit 巴氏合金babbit lined bear ing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器babbit metal 巴氏合金babbit rope socket 灌注式巴氏合金绳头back current 反向电流back e.m.f 反电动势back lash 轮齿隙back plunger type 后部柱塞式(液压梯)back side "后侧,后边"back type governor 轴流式限速器back wall 后壁baked enamel 烤漆balace weight 平衡器balance 平衡balance chain 平衡链balance coefficient 平衡系数balanced traffic 平衡交通ball bearing 滚珠轴承ball cup 球形碗ball pin 球形硝ball stop valve 球形断流器ball type bear ing 滚珠轴承balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade lighting 扶手照明balustrade panel 扶手板balustrade skirting 扶手群板balustrades 扶手装置bandsaw 带锯bank "银行,群组,排"bar "条,棒"bar code 条形码bar lock 杆式锁bare w ire 裸线barricade "防护墙,隔墙"barrier "隔板,栅栏"base "基座,基础"base plate 基板basement 地下室basement service 底下室服务basement type 底吊式basic logic element 基础逻辑元件basic logic function 基础逻辑功能batch production 批量生产battery 电池battery- backed 电池支持的battery box 蓄电池箱battery charger 电池充电器baud rate 波特率BCD(binary coded decimal) 二进制编码的十进制beam 梁beam pad 井道内电缆保护垫片beam pulley 抗绳轮bear ing 轴承bear ing bracket 轴承支架bear ing cap 轴承盖bear ing load 轴承负荷bear ing plate 承重板bear ing play 轴承间隙bear ing sleeve 轴承衬套bear ing stand 轴承座bed lift 病床电梯bed plate 底座bell 铃belt 胶带belt drive 胶带传动belt grinder 胶带磨床belt pulley 胶带轮belt type moving w alk 带式自动人行道bending 弯曲bending stress 弯曲应力benzine 轻汽油bevel gear 伞(斜)齿轮beveled washer 斜垫圈BGM (background music) 背景音乐BGM speaker 背景音乐扬声器bias "偏置,偏移"bid "投标,报价"bid table 报价单bidder 投标bidding cycle 投标有效期限bidding procedure 投标(报价)程序bil of delivery 发货单bil of lading 海运提单bill of expenses 费用帐单bill of materials 材料单billing 开发票binder 装订册bi-parting 对开式(上下开启)bi-parting door 垂直中分门bipartite light transistor 双分式光电管bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关bitumen 沥青blade "叶片,刀片,锯片"blade connector 刀形连接器bleed-off circuit 泄放电路blind hoistway 盲(无门)井道block chart 方框图block diagram 方框图线路block of flats 住宅楼区blocking of contr ol circuit 控制电路闭锁blower 鼓风机blower coil 吹弧线圈blower motor 风机电动机blue print 蓝图boading floor 登梯楼层boading time 登梯时间boarding 登梯boarding landing 登梯层站boarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站boarding zone 登梯区域bobbing 绕线管boldface type 粗字体bolt 螺杆booster 升压机border condition 边界条件bore hole "钻孔,镗孔"boring 镗boring lathe 镗床boring machine 镗床boring miller 镗铣床bottom 底部bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程bottom car runby 底部轿厢越程bottom clearances for car 轿底间隙bottom counterweight clearance 轿底对重间隙bottom counterweight overtravel 轿底对重越程bottom counterweight runby 轿底对重越程bottom door retainer 门下角bottom floor 底部楼层bottom runby 底部越程bottom slow down switch 底部减速开关bottom stop 底部停战bottom ter minal floor 底部楼层bottom ter minal landing 底部端站bottom ter minal stop 底端停站box "盒,箱"box counterweight 箱式对重Braille 盲文字符brake 制动器brake arm 制动器臂brake contact 制动器触点brake coutact 制动器联轴器brake dish 制动盘brake drum 制动轮brake energy 制动力brake level 制动器杠杆brake lever 制动器手柄brake lining 制动器衬套brake linkage 制动器连杆brake operater switch 制动操纵开关brake pin 制动器悄brake press "折弯机,压弯机"brake pulley 制动轮brake release lever 制动器松闸手柄brake release magnet 制动器送闸磁铁brake release time 制动器松闸时间brake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧brake tension 制动器张紧力brake torque 制动器力矩brake wrench 制动器板手braking 制动braking distance 制动距离braking force 制动力branch circuit 分支电路brass founder 铸铜break "切断,破断"break-down 故障breaking load 破断负荷breaking strength 破断强度breaking test 破坏实验breather 通气管brick 砖brick-layer 砖砌工bridge circuit 桥式电路bridge connector 桥接器bridge jumper 桥接片bridge r ectifier 桥式整流器bright controlling 光度控制broach 拉力broaching machine 拉床brochur e 手册broken chain contact 断链触点broken circuit 断路broken dr ive chain contact 主驱动链保护装置broken dr ive-chain safety device 驱动链条保护装置broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点broken step chain device 断绳开关broken step chain safety device 梯级链断列触点broken step safety device 梯级破列安全装置broken tape sweitch 短带开关bronze 铜brunching "成组,成群"brush finished stainless steel 哑光不锈钢brush holder "刷握,滑环"brush yoke 刷架budget 预算buffer 缓冲器buffer base 缓冲器底座buffer plate 缓冲器板buffer plunger 缓冲器柱塞buffer retur n spring 缓冲器复位弹簧buffer stand 缓冲器台buffer striking plate 缓冲器撞板buffer stroke 缓冲器冲程buffer support 缓冲器支承buffer switch 缓冲器开关buider's work drawing 土建图纸buiding facility 大楼设施buiding supervision center 大楼监管中心builder 建筑单位building 建筑building area 建筑面积building contractor 建筑承包商building manager 大楼管理者building monitoring and security system 大楼监管和安全系统building population 大楼居住人口built=in 内装built-in escalator 组合式自动扶梯bumper 弹簧式缓冲器bumper rail 防撞板bumpy r ide 颠簸振动的运行buried 埋入的burn in (程序)灌入burr "毛刺,毛边"burr free 去毛刺bus 总线bus bar 汇流条bush 衬套bushed bearing 加衬轴套bushing "衬套,轴套,套筒"butt joint "平接,对焊"button 按钮button switch 按钮开关buyer 买方buzzer 蜂鸣器buzzer switch 蜂鸣器开关bypass 直驶by-pass button 直驶按钮by-pass valve 溢流阀bypassed floor 直驶不停楼层bypassed stop 直驶不停层站C$F 到岸价cab "轿厢,座舱"cab interior 轿厢内部cabin "轿厢,座舱"cabinet "柜,厢"cable 电缆cable box 电缆箱cable car 缆车cable cleat 电缆夹具cable conductor 电缆导线cable entry 电缆引入cable hanger 电缆吊架cable hole 电缆孔cable joint 电缆接头cable termination 电缆末端cable trunk 电缆接头CAD 计算机辅助设计cage 轿厢cage door 轿厢门calculation 计算机辅助设计calibr ate 校准call "呼梯,呼叫"call acceptance 呼梯接收call accepted 接受呼梯call accepted indicator 接受呼梯指示灯call accepted signal 接受呼梯信号call allocation 呼梯分派call assignment 呼梯指令分配call band 呼梯信号带call button 呼梯按钮call cancel 呼梯取消call canceling 呼梯取消call coincidence 呼梯重合call conmting system 呼梯计数系统call contr l 呼梯指令控制call emitter 呼梯指令发送器call input 呼梯输入call input capacity 呼梯输入内容call input device 呼梯输入装置call load 呼梯输入call memory 呼梯记忆call registered 登陆的呼梯call registered signal 登陆的呼梯信号call registration indicator 呼梯登陆信号call sequence 呼梯顺序call tegistration 呼梯登陆call-back 召修call-back message 召修信息callinfg board 召唤盒calling floor 呼体楼层calling landing 呼梯call-out response time 维修召唤应答时间call-out service 急修服务CAM 计算机辅助制造cam 凸轮cam for positive oper ation 强制操纵凸轮cam lever 偏心柄cam shaft 偏心轴cam tape control 偏心带控制cam-gear 凸轮传动装置cam-operated switch 凸轮(碰铁)操纵开关cancel "撤消,取消"cancelingof call signal 呼梯信号消除cancellation "撤消,取消"canopy "顶盖,大蓬"canvas 帆布canvas hose 帆布软管cap "帽,盖子"cap nut 螺母capacitance "电容,电容量"capacitor 电容capacitor motor 电容器电机capacity "载重,容量,定员"capacity plate 载量标牌capstan 绞盘captive roller safety gear 滚柱式安全钳car 轿厢car annunciator 轿厢报警器car approaching gong 轿厢到站预报钟car apron 轿厢入口群板car assignment "轿厢调度,轿厢分配"car automatic switch landing 轿厢开关自动停站car axis 轿厢中心线car back wall 轿厢后壁car botom clearance 轿厢安全高度car bottom overtravel 轿厢底部越层car bottom runby 底部越程car buffer 轿厢缓冲器car button 轿厢按钮car cab 轿厢体car call 轿厢指令car call button 轿厢指令按钮car call cancel 轿内召唤取消car call control 轿厢指令控制car call panel 轿厢(呼梯)指示盘car call stop 轿厢(呼梯)指令停车car cam 碰铁car canopy 轿厢顶盖car ceiling 轿厢装饰顶car coming indicator 轿厢驶近指示灯car contr ol lever 轿厢操纵手柄car contr ol switch 轿厢操纵开关car counterweight 轿厢对重car cross-head 轿厢上梁car depth 轿厢深度car dispatch 轿厢调度car door 轿门car door catch 轿门栓car door closer 轿门关闭器car door electr ic contact 轿门电触点car door guide shoe 轿门导靴car door inter lock 轿门联锁car door lock 轿门门锁car door rail 轿门导轨car door sill 轿门地坎car door track 轿门导轨car elevator 汽车电梯car emergency exit "轿厢安全门,应急门"car emergency opening 轿厢安全窗car emergency release switch 轿厢应急释放按钮car enclosure panel 轿厢壁板car enclosures 轿厢壁板car entr ance 轿厢入口car extetior "轿厢外装修,轿厢外表"car fan 轿厢风扇car floating movable platfor m 轿厢活动地板car floor frame "轿厢架,轿架"car frame "轿厢架,轿架"car frame attachment 轿厢框架附件car frame plank 轿厢下梁car frame upright 轿厢立柱car front 轿厢前壁car full control 满载轿厢控制car gate 轿厢门car gate contact 轿门触点car gate electric contact 轿门电气触点car guide 轿厢导轨car guide axis 轿厢导轨中心线car handle control "手柄开关操纵,轿内开关控制" car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明car isolation 轿厢隔震器car leveling device 轿厢平层装置car lift 汽车电梯car light 轿厢照明装置car light panel "轿厢照明板,照明天花板"car lighting 轿厢照明car manual switch landing 轿厢手动开关停站car operation board 轿厢操纵盘car operation panel 操纵箱car over load 轿厢超载car panel 轿厢壁板car panel attachment 轿厢壁板附件car panel base 轿厢壁板底座car panel w ith w indow 轿厢壁板上窗口car platform "轿厢底,轿底"car platform guard 轿厢站台护板car platform sill 轿厢car position indicator "轿厢指示灯,轿厢位置显示" car position reference value 轿厢位置参考值car preference 轿厢优先权car push-button 轿厢按钮car rear wall 轿厢后壁car roof "轿厢顶,轿顶"car safety 轿厢安全钳car safety bar for dumbwaiter 轿厢安全棒(杂货梯)car safety gear 轿厢安全钳car safety mechanism switch 轿厢安全钳联动开关car sheave 轿厢绳轮car side emergency door 轿厢安全侧门car side opening 轿厢侧面开门car side wall 轿厢侧壁car sill 轿厢地坎car sling "轿厢架,吊架"car station 轿厢操纵站car status information 轿厢运行状态信息car stop 轿厢停止car suspension 轿厢悬挂装置car switch 轿厢开关car switch automatic floor stop operation 轿厢开关自动停站装置car switch control 轿厢开关控制car switch opration "手柄开关操纵,轿内开关控制"car top 轿厢顶部car top clearance 轿顶安全高度car top emergency exit "轿顶安全出口,轿顶应急出口"car top guard 轿顶护栏car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站)car top light 轿顶照明装置car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆car ventilation 轿厢通风car walls "轿厢壁,轿壁"car weight 轿厢重量car width 轿厢宽度carbon "碳,石墨"carbon brush 碳刷carbon contact 碳精触点carbon steel 碳素钢carburization 渗碳carburize 渗碳carburized hardening 渗碳硬化carburizer 渗碳剂card "卡片,纹板"card reader 卡片读出器cardan joint 万向接头carpet 地毯carriage charges 运费carry frequency "载波频率,开关工作频率"carrying capacity "载运量,载运能力"cart elevator 车辆运货电梯cartridge fuse 插塞式熔断器carving machine 刻模机cascade "级联,串联"cascade sub-loop 串接式子回路case "箱,盒,外壳"casing "保护套,外套"casing of cylinder 油缸套cassette tape 录音带cast bronze 铸青铜cast iron 铸铁cast steel 铸钢casting 铸造castor oil 蓖麻油catch "擎子,门扣,捕捉器"catch block 安全钳catch clip 捕捉夹钳catch device 捕捉装置cathode 阴极cathode ray tube(CR T) 阴极射线管cavitation "气穴,涡穴,饱和压力点"ceiling 吊顶ceiling assembling 轿顶cellulose 纤维板cement "水泥,胶合剂"cement concrete 混凝土cenrifugal brake 离心制动器center 中心center latch 中心门栓center line 中心线center of curvatur e 曲率中心center opening 中分式门center opening door 中分门center opening two speed door 中分四扇门center opening vertical sliding door 中分式垂直滑动门center plunger hydraulic lift 柱塞直顶式液压电梯center support "中心支撑,中间支撑,第三支撑"center-opening folding door 中分式折叠门centigrade 摄氏温度central alarm 中央报警central control board 中央监控盘central control room 中央监控室central jack 中心液压装置central position 中心位置centr ifugal 离心的centr ifugal cast 离心铸造centr ifugal fan 离心式风扇centr ifugal governor 离心式限速器centr ifugal speed 离心速度centr ifugal switch 离心开关centr ifugal type governor 离心式限速器centr ipetal force 向心力ceramic capacitor 搪瓷电容certification 证书certifying body 认证机关chain 链条chain block 手拉葫芦chain bracket 链条托架chain drive 链传动chain drive elevator 链驱动升降机chain drive machine 链驱动机chain gear 链轮chain guard 链防护罩chain link "链节,链环"chain pitch 链条节距chain sag 链条下垂度chain sheave 链轮chain sprocket 链轮chain sustarned elevator 链支撑升降机chain tensioning device 链张紧装置chain w heel 链轮chain w heel track 链轮导轨chamger "倒棱,去毛刺"change switch 转换开关change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性channel 槽钢channel iron 槽铁channel steel 槽钢character "特征,字符"characteristic "特征,特性"characteristic curve 特性曲线charge "充电,收费"charged "带电,充电"charging contactor 充电接触器charging set 充电chart 图表chart of accounts 成本图表check valve 止逆阀chequer(checker)plate 网纹钢板chief engineer 总工程师chime 音钟chip 芯片chipboard 木屑板chisel 凿子choke "扼流,截流,阻塞"choke coil 扼流线圈chopper 斩波器chrome 铬chuck 卡盘CIF(cost insurance and freight) 到岸价cinder concrete 煤渣混凝土circle "周期,圆"circuit 电路circuit breaker "断电器,断路器"circuit diagram 电路图circular pitch 周节circulating pump 循环泵circulation 循环circumferential force 圆周力circumferential speed 圆周速度circumferential velocity 圆周速度CL(center line) 中心线clacking 盖板cladding 装饰clamp 夹clamp ring "压制环,加紧环"clamping jaw 夹钳clamping sleeve 夹紧套桶clamping strap 制动带class of loading 灾荷种类clear depth 净深度clear dimension 净尺寸clear door height 门净高度clear door width 门净宽度clear entrance to the car 轿厢入口净尺寸clear height 净高clear hoistway 井道净尺寸clear width 净宽度clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度clearance top car 轿顶安全高度clearance top counterweight 对重装置顶部安全高度cleated riser 梯级竖板clerance 间隙clevis U型夹client "客户,买主"clip 钳夹clockwise 顺时针的close circuit 闭合电路closed loop 闭环closed position (门)关闭位置closed position monitoring (门)关闭位置检测closed-loop control 闭环控制closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing travel 门关闭运行closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体)CNC(computerized numric contr ol) 计算机数控coast to stop 滑行停车coating 涂层coaxial cable 同轴电缆cock 龙头code "码,符号,规程,规范"code of practice "实施规程,实用规程"code word 代号文字coding PCB(pr inter cicuit boar d) 编码印刷电路板coefficient 系数coefficient of fr iction 摩擦系数coil "线圈,绕组"coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate "栅栏门,折叠式门"collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection "收集,集合"collective control 集中控制collective full automatic operation 全自动集中控制collective operation elevator 集中操作电梯collective selective 集选collective selective contr ol 集选控制collector 集电路collision switch 碰撞开关color 颜色colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column "柱,立柱"comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment "隔板,隔室"compennsating device for hoist ropes 曳引绳补偿装置compensanting/equalizer disk 补偿/补偿器compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent "有资格的,胜任的"competent personnel "有资格的人员,胜任的人员"competitor system 竞争机制component 部件compound w ind motor 复励电动机compound w ound 复绕comprehensive 综合的comprehensive maintenance contract "综合维修合同,全包维修合同" comprehensive service contract "综合维修合同,全包维修合同" compressing spring 压缩弹簧compression 压缩compression switch 压缩开关compressive stre ss 压应力compressor 压缩器compulogic system 电脑程序控制系统computer 计算机computer per ipheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed "隐蔽的,暗式"concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod "连杆,连接杆"connection 连接connection diagram of controller 控制柜连线图connector "接线柱,连接器"conract specification "合同规定,合同明细表"conract speed "合同速度,额定速度"consecutively departing 依次派出的轿厢console panel "控制柜,控制盘"constant "恒定的,常数"constant H P motor 功率恒定型电机constant speed valve "比例控制阀,调速阀"constant torque motor 力矩恒定型电机construction "安装,施工"construction crane 建筑起重机construction layout draw ing 土建图construction platform "安装平台,施工平台" construction site "安装工地,施工工地"consultant "顾问,咨询机构"consumption 消耗contact 触点contact angle 接触角contact br ace 触头撑条contact burning 触头烧损contact carr ier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger "接触指,滑触头"contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷contact mat 触头垫片contact normally closed 常闭触点contact normally open 常开触点contact pr essure 触头压力contact resistance 接触电阻contactless 无触点contactless control 无触点控制contactless control system 无触点控制系统contactless switch 无触点开关contactor 接触器contents 内容conter 计数器continuing travel indicator (轿内)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关contract "合同,契约,承包合同"contract capacity "合同载重量,合同容量"contract load 合同负载contract of indemnity 赔偿合同contract party "合同方,合同当事人"contract work system 合同制度control 控制control amplifier 调节放大器control bus 控制总线control cabinet 控制柜control cable 控制电缆control circuit 控制电路control device for handrail brekage 扶手带断带保护装置control feature 控制特征control gear 控制论control guar d for handrail br eakage 扶手带断带保护装置control lever 控制杆control panel 控制屏control stand 控制台control station 控制站control switgh 控制开关control system 控制系统control system for elevator 电梯控制系统control technique 控制技术control type 控制形式control valve 控制阀control valve unit (液压)调节阀装置control voltage "控制电压,操作电压"controlled angle 控制角controller 控制柜controller base 控制柜底座controller cabinet 控制柜controller panel 控制屏controller w iring diagram 控制柜电路图controlling circuit 控制电路conuter-clockwise 逆时针方向conventional 常规的conventional lift 普通电梯converter "整流器,转换头"converter panel 换流器盘converter set 换流器组件converter unit 换流装置conveyance of passengers 乘客载运conveyer 输送机conveyer track 输送车轨道cooler 冷却装置cooler air-conditioner 空调制冷cooling 冷却cooling device for semiconductor 半导体冷却装置cooling fan 冷却风扇COP(car operation panel) 轿厢操纵盘copper 铜cord "绳索,芯线"cord dr ive "绳传动,(厅门)"core 铁心core press 铁心压力core ventilation 铁心通风cork 软木cork packing 软木盘根corner "角,隔"corner post 对角立柱corpus lift 尸体升降机correct phase sequence 正确相序correcting "修正,校正"correcting travel 校准运行correction "校正,校准"corrective maintenance 校正维修corridor 走廊corrosion proof 防腐蚀的corrosion resistant 耐腐蚀的corrosion resistant coating 涂防锈漆层corrosive 腐蚀的cost "成本,费用"cost accounting 成倍核算cost analysis 成本分析cost calculation 成倍计算cost comparison 成本比较cost effective 价格划算的cost element 成本项目cost estimate 成本估算cost of material 材料成本cost of production 生产成本cost price 成本价cost share 成本份额cost situation 成本状况cost structure 成本结构cost-free 免费的cotter pin 开口销counpler 联轴器counter emf 反电动势counter inductor 记数感应器counter sunk head 埋头counterbalance "相互平衡,配重平衡" countersink "沉头,埋入"counterweight "对重装置,对重"counterweight bottom runby 对重底部越程counterweight filler "对重块,对重装置重鉈" counterweight filler weight "对重块,对重装置重鉈"。
电梯专业英语词汇abbreviation缩语abnormal "不正常得,反常得" abnormalitymonitoring 异常监听abrasion 磨损abrasionresistant耐磨性ﻫabrasive cloth 砂布absorb吸收ﻫabsorber 减振器ﻫACdrive交流拖动ﻫAC feedback control交流反馈控制AC motor 交流电机ﻫAC servo 交流伺服ﻫAC servomotor 交流伺服电机AC single speed 交流单速AC two speed 交流双速ﻫAC twospeedmotor交流双速电动机AC variale speed交流调速ﻫAC(alternating current)交流电ﻫacanning cycle扫描周期,扫描循环ﻫaccelerationcontrolsystem加速度控制系统acceleration(accel)rate加速器ﻫaccelerator加速器ﻫacceptance oflift 电梯验收acceptance period验收阶段acceptancetest验收试验acceptanec certificate 验收证书access door检修门ﻫaccess forbidden 禁止入内accesslift 通道电梯ﻫaccess security 通道防卫ﻫaccessswitch”通道开关,维修用开关" ﻫaccess way 进出通道ﻫaccessibility"可通达性,接近得,难易程度"accessible允许进入accessible space允许进入得场地accessory ”配件,附件"accident事故accident insurance 事故保险accident prevention 事故预防accidentalcontact 触电accidentaloperation误操作ﻫaccordion door 折叠门ﻫaccumulation累积accumulator 蓄电池ﻫAC—GLmachine 交流无齿曳引机acoustic ”听觉得,声音得"acrew die板牙ﻫactivate "启动,触发”activemode 主动模式ﻫactual condition "实际状况,实际条件"actual load 实际载荷actualstate 实际状况actual value 实际值actuate ”开动,操作,激励"actuating linkege操作连杆ﻫactuating magnet操作磁铁ﻫactuation time 动作时间actuator”操纵机构,激励器,螺线管"actuator bracket调节器支架ﻫactuator plate调节板ﻫACVFdrive交流调频拖动ﻫACVF system交流调频系统ﻫACVF(ACvarible frequency)交流调速ﻫACVV dirve 交流调压拖动ACVV system 交流调压系统ACVV(AC varible voltage) 交流调压ﻫadaptation"适应,匹配”ﻫadapterPCB 选通脉冲印刷电路板ﻫadapter(adapator)适配器ﻫadapting选配adaptive control system 自适应能力控制系统addendum "齿顶高,附录”addendum circle 外圆ﻫadding workingdrawing 附加加工图ﻫaddition "附加物,加法"additional materials 附加材料address 地址ﻫadhesion”胶,粘合胶”adhesionprotectiveoil防粘油adhesivefoil 胶粘薄膜adhesive tape 胶带adjacent 邻近得ﻫadjacent car "相邻轿厢,相邻电梯”adjacent entrance 相邻出入口adjusment 调试adjustable condensor 可变电容器ﻫadjustable resistance可调电阻ﻫadjustable spanner可调扳手adjustable speedelectric drive 调速电力拖动ﻫadjustable wrench ”活动扳手,可调扳手"adjusting screw 调节螺丝adjustor 调试员administationoverjhead rate 管理费用标准administrationcost 管理成本administration expenses 管理费用ﻫadvance door opening 提前开门advance payment 预付款advanced"提前得,先进得”advanced carriage超前拖板(选层器)ﻫadvancingpositionreference value 超前位置参考值ﻫaerial cableway"空中缆车,架空索道"ﻫaerialropeway”空中缆车,架空索道"aerial tramway ”空中缆车,架空索道”aesthetic美观aftersales service售后服务ﻫagency 代理agenda 议程ﻫair cord (门机用)航空钢丝绳ﻫair purifier 空气滤清剂airventilator通风管ﻫair—bleed空气分泄器airbornenoise空气传播噪声ﻫair—condition 空调ﻫair—gap 气隙alarm警报alarmbell警铃alarmbutton警铃按钮ﻫalarm buzzer 警报蜂鸣器ﻫalarmcircuit 警报电路alarm system 警报系统ALC(autoclaved light—weight concrete) 蒸压轻质混凝土ﻫalcove arrangement电梯U型排列法ﻫalgorithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignmentgauge 校正量规ﻫalkali 碱ﻫall—puter-controlled 计算机全控得allocation ”分配,分派"allocationof landingcall层站呼梯指令分配allowance ”允用误差,加工余量" ﻫallowblestress for temporaryload允许暂时应力值ﻫalloy合金alloy steel 合金钢alteration 改进ﻫalternate floor 隔层ﻫalumina氧化铝aluminum 铝ﻫaluminum alloy铝合金aluminumbronze 铝青铜ﻫaluminum cladding铝制包层ﻫalumite防蚀铝ﻫalundum 氧化铝ﻫambient环境得ﻫambientnoise 环境噪音ambient temperature环境温度ammeter安培计ammonia 氨amperage电流强度ﻫampere安培amplification 放大amplification stage 放大等级ﻫamplifier放大器amplifyingtube 放大管ﻫamplitude幅度analog adder 模拟加法器analog puter模拟计算机analog speed card 模拟曲线板ﻫanalog-digitalconverter模拟-数字转换器ﻫanalogue(analog)模拟analysis分析analysis mode分析模拟anchor bolt 地脚螺栓ﻫanchorage"锚具,锚定" ﻫangle bar 角钢ﻫangle guide角铁导轨ﻫangle iron 角铁angle iron frame角铁框架angle ofcontact 接触角angle of deflection导向角ﻫangle of inclination 倾斜角ﻫangle of lead导程角angle oftraction曳引机包角ﻫangleof wrap包角anglesteel 角钢ﻫangular contactball bearing向心推力球轴承ﻫangular contact bearing 角面接触滚动轴承ﻫangular gear斜齿轮ﻫangular retardationg 角减速度angular velocity 角速度ﻫanneal退火annealing 退火ﻫannual inspection 年检ﻫannual report 年度报告ﻫannunciator "报音器,声音合成器"anode阳极ﻫanodize氧极氧化ﻫANSI(America Nationa StandardInstirute)美国国家标准协会ﻫanti—clockwise 逆时钟方向anti-corrosive paint防腐蚀漆anti-creep防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰ﻫanti-nuisance device防捣乱装置anti—phasebraking 反向制动ﻫanti-phase current 反相电流ﻫanti-reboundof pensationrope device 补偿绳防跳装置anti—residual 防剩磁ﻫanti-resonance抗谐振anti—reversiondevice 防反转装置anti—rust 防锈ﻫanti—stall 防空转ﻫanti-vibralionpad防震垫ﻫAPM(automaticpeople mover)自动人员运输机apparen power 视在功率ﻫapparent output 视在输出ﻫapplicant 申请人application申请ﻫapplication guide 应用指南aprons 裙板ﻫarbour”轴,杆”arcchamber电弧隔离室arc protection 防电弧arc quenching 熄焊弧ﻫarc shield电弧屏蔽ﻫarcsuppressor 灭焊器architect 设计单位ﻫarchitecture 建筑学architrave门框area面积arm"臂,支路"armature电驱armature coil 电驱线圈armaturecurrent 电驱电流ﻫarmature lamination 电驱铁芯片armature shaft电驱轴ﻫarmaturespider星形轮ﻫarmaturewinding电驱绕组armoured 蛇皮管得armouredcable蛇皮管电缆ﻫarmoured conduit导线管ﻫarrangement布置ﻫarrival bell到站铃arrivalbuzer到站蜂鸣器ﻫarrival floor 到达楼层arrivalgong 到站钟ﻫarrival rate 到站率ﻫarticleofconsumption 消耗品ﻫartificialintelligence人工智能artistic工艺artistic face工艺表面ﻫasbestospacking石棉盘根ascending上升ASIC(application specific integratedcircuit)专用集成电路assemble装配assembler language 汇编语言assembly of hinge 铰链组装assign分配astragal 装饰镶条ﻫatmospheric influence 大气影响ﻫattachment附件ﻫattendant con trol 有司机控制attendantcontrol partment有司机控制盒ﻫattendantoperation有司机操作audiblesignal 音响信号audio tape recording 磁带录音authority"当局,核准部门”ﻫauthority of liftacceptance 电梯验收部门ﻫauthorized"授权得,核准得"authorized user核准使用者auto-adaptation 自适用AutoCAD 自动计算机辅助设计ﻫautographic recoder自动记录仪automatic自动得automatic allocator 自动分派器ﻫautomatic by-pass 自动直驶ﻫautomatic center opening sliding door自动中分式滑动门automatic closer自动关闭门ﻫautomatic dispatch自动调度automatic door自动门ﻫautomatic homing自动回基层ﻫautomatic landing 自动停站ﻫautomatic landingsystem by spare battery 靠备用蓄电池得自动停站设备ﻫautomaticleveling自动平层automatic lubricator自动润滑装置automatic parkinggarage自动停车库automatic parking system 自动停车系统automatic relevelling自动平层校正ﻫautomaticrescue device应急救助装置automaticreturn 自动返回ﻫautomatictelescopic center openingslidingdoor 自动中分式折叠滑动门automatic telescopic sliding door自动折叠式滑动门automobile lift汽车电梯autowalk 自动人行道ﻫauxiliary apparatus 辅助装置auxiliary brake辅助制动器ﻫauxiliary cicuit 辅助电路ﻫauxiliarycontact辅助触点ﻫauxiliary drive 辅助驱动auxiliary lock辅助锁ﻫauxiliary materials 辅助量auxiliary value 辅助材料auxiliary winding辅助绕组ﻫavailable area有效面积ﻫaverage平均averagecar load平均轿厢负载average dispatching interval平均调度间隔时间ﻫaverage interval 平均调度间隔时间ﻫaverage passengerwaitingtime平均乘客侯梯时间average response time平均应答时间average waiting quest 平均乘客量averagewaiting time 平均乘客侯梯时间axialflow fan轴流式风扇axis 轴线ﻫaxle 轴babbit 巴氏合金babbit lined bearing巴氏合金衬里轴承babbitmelter巴氏合金熔化器ﻫbabbitmetal巴氏合金babbit rope socket灌注式巴氏合金绳头ﻫbackcurrent反向电流backe、m、f反电动势ﻫbacklash 轮齿隙backplunger type 后部柱塞式(液压梯) ﻫback side "后侧,后边"ﻫback typegovernor轴流式限速器ﻫback wall 后壁bakedenamel烤漆balace weight 平衡器ﻫbalance平衡ﻫbalance chain 平衡链balance coefficient 平衡系数balancedtraffic平衡交通ﻫball bearing滚珠轴承ﻫball cup 球形碗ﻫball pin 球形硝ﻫball stopvalve 球形断流器ﻫballtype bearing滚珠轴承ballast 镇流器balustradedeching 外侧盖板ﻫbalustrade exterior panelling 外装饰板balustrade lighting 扶手照明ﻫbalustrade panel 扶手板ﻫbalustrade skirting 扶手群板ﻫbalustrades 扶手装置bandsaw 带锯ﻫbank”银行,群组,排”bar”条,棒"ﻫbar code 条形码bar lock 杆式锁ﻫbare wire裸线ﻫbarricade ”防护墙,隔墙”ﻫbarrier"隔板,栅栏" ﻫbase ”基座,基础”base plate 基板basement地下室basement service底下室服务basement type底吊式ﻫbasic logic element基础逻辑元件ﻫbasic logicfunction 基础逻辑功能ﻫbatch production 批量生产ﻫbattery 电池ﻫbattery-backed电池支持得battery box 蓄电池箱ﻫbatterycharger电池充电器baudrate 波特率BCD(binary codeddecimal)二进制编码得十进制beam梁ﻫbeam pad 井道内电缆保护垫片beam pulley抗绳轮bearing轴承bearing bracket 轴承支架ﻫbearing cap轴承盖bearingload轴承负荷ﻫbearingplate承重板ﻫbearing play 轴承间隙bearing sleeve轴承衬套bearing stand轴承座ﻫbedlift 病床电梯bed plate底座ﻫbell 铃belt 胶带ﻫbelt drive胶带传动ﻫbelt grinder胶带磨床ﻫbeltpulley 胶带轮belt type movingwalk带式自动人行道ﻫbending弯曲ﻫbending stress弯曲应力benzine轻汽油ﻫbevel gear伞(斜)齿轮ﻫbeveledwasher 斜垫圈BGM (background music)背景音乐ﻫBGM speaker背景音乐扬声器ﻫbias"偏置,偏移”bid ”投标,报价”bid table 报价单bidder投标ﻫbidding cycle 投标有效期限ﻫbidding procedure投标(报价)程序ﻫbil o fdelivery 发货单bil of lading海运提单bill ofexpenses 费用帐单billof materials材料单ﻫbilling开发票binary 二进制binder 装订册ﻫbi-parting 对开式(上下开启)bi—parting door 垂直中分门bipartite light transistor 双分式光电管ﻫbistable magnetic swich 双稳态磁开关ﻫbistable switch双稳态磁开关bitumen 沥青blade "叶片,刀片,锯片”bladeconnector 刀形连接器bleed—off circuit泄放电路ﻫblind hoistway 盲(无门)井道ﻫblock chart方框图block diagram方框图线路ﻫblockof flats 住宅楼区ﻫblocking ofcontrol circuit 控制电路闭锁blower鼓风机ﻫblower coil吹弧线圈ﻫblowermotor 风机电动机ﻫblueprin t蓝图boadingfloor登梯楼层ﻫboading time登梯时间boarding 登梯ﻫboardinglanding 登梯层站ﻫboarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站ﻫboarding zone 登梯区域ﻫbobbing绕线管ﻫboldfacetype 粗字体ﻫbolt 螺杆ﻫbooster 升压机ﻫborder condition边界条件ﻫbore hole"钻孔,镗孔"boring镗ﻫboringlathe镗床boring machine 镗床boringmiller镗铣床ﻫbottom底部bottom car clearance 轿底安全高度间隙bottomcar overtravel底部轿厢越程bottom carrunby底部轿厢越程bottom clearances forcar轿底间隙ﻫbottom counterweight clearance 轿底对重间隙ﻫbottom counterweight overtravel轿底对重越程bottom counterweightrunby 轿底对重越程bottom door retainer门下角ﻫbottom floor 底部楼层ﻫbottom runby 底部越程ﻫbottom slow downswitch 底部减速开关ﻫbottomstop底部停战bottom terminalfloor 底部楼层bottom terminal landing 底部端站ﻫbottom terminal stop 底端停站ﻫbox"盒,箱”ﻫbox counterweight 箱式对重ﻫBraille 盲文字符ﻫbrake 制动器brake arm制动器臂ﻫbrake contact 制动器触点ﻫbrake coutact 制动器联轴器ﻫbrake dish 制动盘ﻫbrake drum 制动轮brake energy 制动力ﻫbrake level 制动器杠杆ﻫbrake lever制动器手柄ﻫbrake lining 制动器衬套brake linkage制动器连杆brake operater switch制动操纵开关ﻫbrake pin 制动器悄brake press ”折弯机,压弯机" ﻫbrake pulley 制动轮brake release lever制动器松闸手柄ﻫbrake release magnet 制动器送闸磁铁brakerelease time 制动器松闸时间ﻫbrake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧ﻫbrake tension制动器张紧力ﻫbraketorque 制动器力矩ﻫbrake wrench制动器板手braking 制动braking distance 制动距离braking force 制动力branchcircuit分支电路ﻫbrassfounder 铸铜ﻫbreak "切断,破断" ﻫbreak-down 故障breaking load破断负荷breakingstrength破断强度ﻫbreaking test破坏实验ﻫbreather通气管ﻫbrick 砖brick—layer 砖砌工ﻫbridge circuit 桥式电路bridgeconnector桥接器ﻫbridgejumper桥接片bridgerectifier 桥式整流器ﻫbright controlling 光度控制ﻫbroach 拉力broachingmachine 拉床brochure 手册broken chain contact断链触点broken circuit 断路ﻫbroken drive chain contact主驱动链保护装置broken drive-chain safety device 驱动链条保护装置broken rope contact 驱动链条列断安全装置ﻫbroken step chain contact 断绳触点broken step chaindevice 断绳开关broken stepchainsafetydevice 梯级链断列触点broken stepsafety device 梯级破列安全装置broken tape sweitch 短带开关bronze铜brunching"成组,成群" ﻫbrush finishedstainless steel哑光不锈钢brushholder "刷握,滑环"brush yoke刷架budget预算ﻫbuffer 缓冲器buffer base 缓冲器底座buffer plate缓冲器板buffer plunger缓冲器柱塞buffer return spring缓冲器复位弹簧buffer stand缓冲器台bufferstriking plate缓冲器撞板buffer stroke缓冲器冲程buffer support 缓冲器支承buffer switch 缓冲器开关ﻫbuider'swork drawing 土建图纸buiding facility大楼设施ﻫbuidingsupervision center 大楼监管中心ﻫbuilder 建筑单位ﻫbuilding 建筑buildingarea 建筑面积ﻫbuilding contractor建筑承包商buildingmanager大楼管理者ﻫbuilding monitoringand securitysystem大楼监管与安全系统building population大楼居住人口built=in 内装ﻫbuilt—in escalator组合式自动扶梯ﻫbumper弹簧式缓冲器ﻫbumperrail防撞板ﻫbumpy ride颠簸振动得运行ﻫburied 埋入得ﻫburn in (程序)灌入ﻫburr”毛刺,毛边"burr free 去毛刺ﻫbus 总线ﻫbusbar 汇流条bush衬套bushed bearing加衬轴套bushing ”衬套,轴套,套筒" ﻫbuttjoint"平接,对焊"ﻫbutton按钮ﻫbutton switch按钮开关ﻫbuyer 买方ﻫbuzzer蜂鸣器ﻫbuzzer switch 蜂鸣器开关ﻫbypass直驶ﻫby-pass button直驶按钮by-pass valve溢流阀bypassedfloor 直驶不停楼层ﻫbypassed stop直驶不停层站C$F到岸价ﻫcab "轿厢,座舱”cab interior 轿厢内部cabin”轿厢,座舱"cabinet "柜,厢"cable 电缆cable box电缆箱ﻫcable car缆车cable cleat 电缆夹具cableconductor电缆导线cableentry电缆引入ﻫcable hanger电缆吊架cablehole电缆孔ﻫcable joint 电缆接头cable termination电缆末端ﻫcable trunk电缆接头CAD 计算机辅助设计cage 轿厢cagedoor轿厢门calculation计算机辅助设计calibrate校准ﻫcall"呼梯,呼叫”ﻫcall acceptance 呼梯接收ﻫcall accepted接受呼梯ﻫc all acceptedindicator 接受呼梯指示灯ﻫcall accepted signal 接受呼梯信号ﻫcallallocation呼梯分派callassignment 呼梯指令分配call band 呼梯信号带ﻫcallbutton 呼梯按钮call cancel 呼梯取消callcanceling呼梯取消callcoincidence 呼梯重合ﻫcall conmtingsystem 呼梯计数系统call contrl呼梯指令控制ﻫcall emitter呼梯指令发送器callinput呼梯输入call input capacity 呼梯输入内容ﻫcall input device 呼梯输入装置callload 呼梯输入ﻫcallmemory 呼梯记忆call registered 登陆得呼梯ﻫcall registered signal 登陆得呼梯信号call registration indicator 呼梯登陆信号call sequence呼梯顺序ﻫcalltegistration呼梯登陆call-back 召修call-backmessage 召修信息ﻫcallinfg board召唤盒callingfloor呼体楼层ﻫcallinglanding 呼梯call—outresponsetime 维修召唤应答时间call-outservice 急修服务CAM计算机辅助制造cam 凸轮ﻫcam for positive operation 强制操纵凸轮ﻫcamlever偏心柄cam shaft偏心轴ﻫcam tapecontrol 偏心带控制ﻫcam-gear凸轮传动装置cam—operated switch凸轮(碰铁)操纵开关ﻫcancel "撤消,取消”ﻫcancelingofcall signal 呼梯信号消除cancellation"撤消,取消"canopy"顶盖,大蓬”canvas 帆布ﻫcanvas hose 帆布软管ﻫcap”帽,盖子"cap nut螺母ﻫcapacitance”电容,电容量"capacitor 电容capacitor motor 电容器电机ﻫcapacity"载重,容量,定员"capacityplate载量标牌capstan绞盘captive rollersafety gear 滚柱式安全钳ﻫcar 轿厢carannunciator 轿厢报警器ﻫcar approaching gong 轿厢到站预报钟ﻫcar apron 轿厢入口群板carassignment"轿厢调度,轿厢分配" ﻫcar automaticswitch landing轿厢开关自动停站caraxis 轿厢中心线carback wall 轿厢后壁ﻫcar botom clearance轿厢安全高度ﻫcar bottom overtrave l轿厢底部越层car bottom runby底部越程carbuffer 轿厢缓冲器ﻫcarbutton轿厢按钮ﻫcar cab 轿厢体ﻫcar call 轿厢指令car call button 轿厢指令按钮ﻫcar call cancel 轿内召唤取消carcall control轿厢指令控制car callpanel轿厢(呼梯)指示盘ﻫcarcall stop 轿厢(呼梯)指令停车carcam碰铁car canopy轿厢顶盖ﻫcarceiling轿厢装饰顶car ing indicator 轿厢驶近指示灯car control lever 轿厢操纵手柄carcontrolswitch 轿厢操纵开关ﻫcarcounterweight 轿厢对重ﻫcarcross—head轿厢上梁ﻫcar depth 轿厢深度car dispatch 轿厢调度ﻫcar door 轿门car door catch 轿门栓cardoor closer 轿门关闭器car doorelectric contact轿门电触点car door guideshoe 轿门导靴car door interlock 轿门联锁car doorlock 轿门门锁ﻫcardoor rail 轿门导轨cardoorsill 轿门地坎ﻫcardoortrack 轿门导轨ﻫcar elevator 汽车电梯car emergency exit"轿厢安全门,应急门"car emergencyopening轿厢安全窗ﻫcaremergency releaseswitch轿厢应急释放按钮car enclosure panel 轿厢壁板ﻫcar enclosures轿厢壁板ﻫcarentrance 轿厢入口ﻫcar extetior "轿厢外装修,轿厢外表”carfan 轿厢风扇carfloating movable platform 轿厢活动地板car floor frame ”轿厢架,轿架"ﻫcar frame "轿厢架,轿架" ﻫcar frame attachment 轿厢框架附件car frame plank轿厢下梁car frame upright轿厢立柱ﻫcar front 轿厢前壁car fullcontrol满载轿厢控制car gate 轿厢门ﻫcar gate contact 轿门触点car gateelectric contact 轿门电气触点carguide轿厢导轨carguide axis 轿厢导轨中心线car handlecontrol”手柄开关操纵,轿内开关控制"car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明ﻫcar isolation 轿厢隔震器carleveling device 轿厢平层装置ﻫcarlift汽车电梯car light轿厢照明装置ﻫcarlight panel”轿厢照明板,照明天花板"ﻫcarlighting轿厢照明car manual switch landing 轿厢手动开关停站car operationboard 轿厢操纵盘car operationpanel 操纵箱caroverload轿厢超载ﻫcar panel 轿厢壁板ﻫcarpanel attachment 轿厢壁板附件ﻫcar panelbase 轿厢壁板底座car panel with window轿厢壁板上窗口ﻫcar platform"轿厢底,轿底”ﻫcarplatformguard 轿厢站台护板ﻫcar platform sill轿厢ﻫcar position indicator"轿厢指示灯,轿厢位置显示”car position reference value轿厢位置参考值ﻫcar preference轿厢优先权ﻫcarpush-button 轿厢按钮ﻫcar rear wall 轿厢后壁car roof"轿厢顶,轿顶"carsafety轿厢安全钳car safety bar fordumbwaiter轿厢安全棒(杂货梯) ﻫcar safety gear 轿厢安全钳car safety mechanismswitch轿厢安全钳联动开关ﻫcar sheave轿厢绳轮car side emergency door 轿厢安全侧门ﻫcar side opening轿厢侧面开门car side wall 轿厢侧壁ﻫcarsill轿厢地坎ﻫcarsling ”轿厢架,吊架"ﻫcar station轿厢操纵站carstatusinformation 轿厢运行状态信息ﻫcarstop 轿厢停止carsuspension轿厢悬挂装置car switch 轿厢开关ﻫcar switch automatic floor stopoperation 轿厢开关自动停站装置carswitch control 轿厢开关控制ﻫcar switch opration "手柄开关操纵,轿内开关控制"cartop 轿厢顶部cartopclearance 轿顶安全高度cartop emergency exit ”轿顶安全出口,轿顶应急出口"car top guard 轿顶护栏cartop inspection device轿顶检修装置car top inspection station轿顶检修盒(站)ﻫcar top light 轿顶照明装置cartop protection balustrade轿顶防护栏杆cartop protection railing轿顶防护栏杆ﻫcar ventilation 轿厢通风ﻫcarwalls”轿厢壁,轿壁”ﻫcarweight轿厢重量car width 轿厢宽度carbon "碳,石墨”carbon brush 碳刷ﻫcarbon contact 碳精触点carbon steel碳素钢carburization 渗碳carburize渗碳ﻫcarburizedhardening渗碳硬化ﻫcarburizer 渗碳剂card”卡片,纹板" ﻫcard reader 卡片读出器ﻫcardanjoint 万向接头ﻫcarpet地毯carriagecharges 运费ﻫcarry frequency”载波频率,开关工作频率”carrying capacity "载运量,载运能力"cart elevator 车辆运货电梯ﻫcartridge fuse 插塞式熔断器carving machine刻模机cascade "级联,串联”ﻫcascadesub-loop串接式子回路case"箱,盒,外壳"casing"保护套,外套" ﻫcasingof cylinder油缸套ﻫcassette tape 录音带cast bronze 铸青铜ﻫcast iron 铸铁caststeel铸钢casting铸造castor oil蓖麻油catch”擎子,门扣,捕捉器”catch block 安全钳ﻫcatch clip 捕捉夹钳ﻫcatch device捕捉装置ﻫcathode 阴极cathode ray tube(CRT)阴极射线管ﻫcavitation"气穴,涡穴,饱与压力点"ceiling吊顶ceiling assembling 轿顶cellulose 纤维板ﻫcement "水泥,胶合剂" ﻫcementconcrete 混凝土ﻫcenrifugal brak e离心制动器center中心center latch中心门栓centerline 中心线center of curvature曲率中心center opening中分式门center opening door 中分门center opening two speed door中分四扇门ﻫcenter opening verticalsliding door 中分式垂直滑动门ﻫcenterplunger hydrauliclift 柱塞直顶式液压电梯center support ”中心支撑,中间支撑,第三支撑" ﻫcenter—opening folding door 中分式折叠门centigrade 摄氏温度central alarm中央报警ﻫcentral controlboard 中央监控盘ﻫcentralcontrol roo m中央监控室ﻫcentral jack中心液压装置ﻫcentral position中心位置centrifugal 离心得centrifugalcast 离心铸造centrifugal fan 离心式风扇ﻫcentrifugal governor离心式限速器centrifugalspeed 离心速度centrifugalswitch离心开关centrifugal type governor 离心式限速器ﻫcentripetalforce向心力ﻫceramic capacitor 搪瓷电容certification 证书ﻫcertifying body认证机关chain 链条chain block手拉葫芦chain bracket链条托架chain drive链传动chaindriveelevator链驱动升降机ﻫchain drive machine 链驱动机chain gear 链轮chain guard 链防护罩ﻫchain link "链节,链环"ﻫchainpitch 链条节距ﻫchain sag链条下垂度chain sheave 链轮ﻫchainsprocket链轮ﻫchainsustarned elevator 链支撑升降机ﻫchain tensioning device链张紧装置ﻫchain wheel 链轮ﻫchain wheel track 链轮导轨ﻫchamger”倒棱,去毛刺”ﻫchange switch转换开关change—over contact转化触点change-overlanding 换乘电梯层站change—over switch 转换开关ﻫchange—pole变化极性channel 槽钢ﻫchannel iron槽铁channel steel槽钢character ”特征,字符"characteristic ”特征,特性" ﻫcharacteristic curve特性曲线ﻫcharge "充电,收费”ﻫcharged ”带电,充电"chargingcontactor 充电接触器ﻫchargingset充电chart图表ﻫchart of accounts 成本图表check valve 止逆阀ﻫchequer(checker)plate网纹钢板chief engineer总工程师chime 音钟chip芯片ﻫchipboard 木屑板ﻫchisel 凿子choke "扼流,截流,阻塞" ﻫchoke coil扼流线圈ﻫchopper斩波器ﻫchrome铬ﻫchuck 卡盘ﻫCIF(cost insurance and freight) 到岸价cinder concrete煤渣混凝土ﻫcircle "周期,圆"ﻫcircuit电路ﻫcircuit breaker "断电器,断路器”circuitdiagram 电路图circular pitch周节ﻫcirculatingpump循环泵circulation 循环ﻫcircumferential force圆周力ﻫcircumferential speed 圆周速度circumferentialvelocity 圆周速度CL(centerline)中心线ﻫclacking 盖板ﻫcladding 装饰clamp 夹ﻫclampring"压制环,加紧环”clamping jaw夹钳ﻫclamping sleeve 夹紧套桶ﻫclamping strap制动带ﻫclassof loading灾荷种类clear depth 净深度cleardimension 净尺寸ﻫcleardoor height 门净高度clear door width 门净宽度ﻫclear entrance tothe car轿厢入口净尺寸ﻫclear height 净高clear hoistway 井道净尺寸ﻫclearwidth净宽度ﻫclearancebetween skirt panels裙板间隙clearancebottom car 轿底安全高度ﻫclearancetopcar 轿顶安全高度clearance top counterweight对重装置顶部安全高度ﻫcleated riser梯级竖板ﻫclerance 间隙clevis U型夹client ”客户,买主" ﻫclip 钳夹clockwise顺时针得close circuit闭合电路closedloop 闭环ﻫclosed position(门)关闭位置closed position monitoring(门)关闭位置检测ﻫclosed-loop control 闭环控制closed-type motor闭合式电动机ﻫcloser关门器ﻫclosingforce (门)关闭力ﻫclosing speed 门关闭速度closingtravel 门关闭运行ﻫclosingvalve切断阀clutch离合器ﻫclutch ponent离合器部件clutch plate离合器板ﻫclutch release sleeve离合器释放套管ﻫclutch spring离合器弹簧CMOS互补型金属氧化物(半导体)CNC(puterized numric control) 计算机数控coast to stop滑行停车coating涂层coaxial cable同轴电缆ﻫcock 龙头code"码,符号,规程,规范”code ofpractice"实施规程,实用规程" ﻫcode word代号文字ﻫcoding PCB(printer cicuit board)编码印刷电路板ﻫcoefficient 系数coefficient of friction摩擦系数ﻫcoil "线圈,绕组”coil case 线圈外壳coiledspring 螺旋弹簧ﻫcoincidence memory 重合记忆ﻫcoinciding call 重合呼梯指令ﻫcold cathode 冷阴极collapsible door 栅栏门ﻫcollapsible gate"栅栏门,折叠式门"ﻫcollapsibletype doo r折叠式门collar环collecting brush 集电刷ﻫcollecting ring 轴环ﻫcollection"收集,集合"ﻫcollectivecontrol集中控制ﻫcollectivefull automatic operation 全自动集中控制ﻫcollectiveoperation elevator 集中操作电梯collective selective 集选ﻫcollectiveselective control 集选控制ﻫcollector 集电路collisionswitch 碰撞开关ﻫcolor 颜色colored starnlesssteel 彩色不锈钢ﻫcolorfast不褪色得ﻫcolorless 无色得ﻫcolumn”柱,立柱"ﻫb contact 梳齿板安全装置ﻫb floor plate梳齿板ﻫb light 梳齿灯b lighting梳齿板照明b plate 梳齿板ﻫb plate contact 梳齿板触板ﻫb plate safetydevice梳齿板安全装置ﻫmutation 整流ﻫmutator 换向环ﻫmutator brush 整流子电刷mutator lug 整流片ﻫmutatormetallic segment金属整流器pact紧凑得parator 比较器partment "隔板,隔室"pennsatingdevicefor hoistropes曳引绳补偿装置ﻫpensanting/equalizer di sk 补偿/补偿器ﻫpensating 补偿ﻫpensating chaindevice 补偿链装置ﻫpensating condensor补偿电容器pensating devece 补偿装置pensatingrope 补偿绳pensating rope device 补偿绳装置ﻫpensating ropehitch补偿绳绳头板ﻫpensating rope sheave 补偿绳轮ﻫpensating rope socket 补偿绳绳头ﻫpensating winding 补偿绳绕组ﻫpensating—ropesheave safetyswitch 补偿绳轮安全开关ﻫpensating-rope sheaves witch 补偿绳轮开关ﻫpensation chain 补偿链ﻫpensationcoil补偿绳线圈pensationrope补偿绳pensationsheave 补偿绳轮ﻫpetent "有资格得,胜任得"petent personnel ”有资格得人员,胜任得人员”petitor system 竞争机制ponent部件ﻫpound wind motor复励电动机pound wound复绕ﻫprehensive 综合得prehensivemaintenance contract”综合维修合同,全包维修合同" ﻫprehensiveservice contract "综合维修合同,全包维修合同”pressing spring 压缩弹簧pression 压缩ﻫpression switch 压缩开关ﻫpressivestress 压应力pressor 压缩器ﻫpulogic system 电脑程序控制系统ﻫputer 计算机puter peripheral devices计算机外围装置puter simulation计算机模拟puting power运算容量ﻫconcealed "隐蔽得,暗式” ﻫconcealed hinge 暗式链条ﻫconcentrated load 集中载荷concentricity 同心性ﻫconclusion ofcontract合同成交ﻫconcrete 混凝土ﻫconcretehoistway 混凝土井道ﻫconcretemachineblock 混凝土机座ﻫconcrete wall 混凝土墙ﻫcondenser 电容器ﻫcondenser for powerfactor improvement 功率因素补偿电容ﻫcondition 条件ﻫconditionof payment付款条件ﻫconditionsof contract合同条件conducting wire 导线conductive 导电得conductor 导体ﻫconduit导线管ﻫconduitfitting 导线管接头conerollerbearing 滚锥轴承ﻫconferenceroom会议室ﻫconical brake 锥形制动器conicalpin锥销ﻫconicity 锥度connect inseries 串接ﻫconnectingpiece连接件connectingrod "连杆,连接杆"connection 连接connection diagramof controller 控制柜连线图ﻫconnector"接线柱,连接器" ﻫconractspecification "合同规定,合同明细表" ﻫconractspeed "合同速度,额定速度”consecutively departing依次派出得轿厢consolepanel”控制柜,控制盘"constant"恒定得,常数”constant HP motor功率恒定型电机constantspeed valve "比例控制阀,调速阀" ﻫconstant torque motor 力矩恒定型电机construction "安装,施工"construction crane 建筑起重机construction layoutdrawing土建图construction platform "安装平台,施工平台"ﻫconstruction site ”安装工地,施工工地"ﻫconsultant "顾问,咨询机构"ﻫconsumption 消耗ﻫcontact 触点contact angle接触角contact brace 触头撑条ﻫcontact burning 触头烧损contact carrier触头支架contact control有触点控制ﻫcontact control system 有触点控制系统ﻫcontactfinger "接触指,滑触头" ﻫcontact forcibly actuated强迫操动触头ﻫcontact holder触头固定架ﻫcont act input 接触输入端ﻫcontact load 保证(额定)载荷contact mat 触头垫片ﻫcontactnormally closed常闭触点ﻫcontact normally open常开触点ﻫcontactpressure触头压力ﻫcontact resistance接触电阻contactless 无触点ﻫcontactless control 无触点控制ﻫcontactless control system 无触点控制系统ﻫcontactless switch 无触点开关contactor 接触器contents 内容conter计数器ﻫcontinuing travel indicator(轿内)继续运行指示器continuouslinearrangement 连锁配置continuous speedregulation 连续速度控制continuous-pressure button继压开关contract "合同,契约,承包合同”ﻫcontract capacity "合同载重量,合同容量" ﻫcontractload 合同负载ﻫcontractof indemnity赔偿合同contractparty "合同方,合同当事人"contract work system合同制度ﻫcontrol控制ﻫcontrol amplifier 调节放大器controlbus 控制总线controlcabinet 控制柜controlcable 控制电缆controlcircuit控制电路control devicefor handrail brekage扶手带断带保护装置controlfeature控制特征ﻫcontrolgear 控制论control guardfor handrailbreakage扶手带断带保护装置ﻫcontrollever 控制杆control panel控制屏ﻫcontrolstand 控制台control station 控制站ﻫcontrol switgh 控制开关ﻫcontrol system 控制系统control systemfor elevator 电梯控制系统ﻫcontrol technique 控制技术ﻫcontroltype 控制形式ﻫcontrol valve 控制阀control valve unit(液压)调节阀装置ﻫcontrolvoltage ”控制电压,操作电压”controlled angle控制角controller控制柜controller base控制柜底座ﻫcontrollercabinet 控制柜ﻫcontroller panel控制屏controller wiring diagram控制柜电路图ﻫcontrolling circuit控制电路conuter—clockwise逆时针方向conventional 常规得ﻫconventionallift普通电梯ﻫconverter"整流器,转换头” ﻫconverter panel换流器盘converter set 换流器组件ﻫconverter unit换流装置conveyanceof passengers 乘客载运conveyer输送机ﻫconveyer track输送车轨道ﻫcooler 冷却装置ﻫcoolerair-conditioner 空调制冷ﻫcooling冷却coolingdevice for semiconductor 半导体冷却装置ﻫcooling fan 冷却风扇ﻫCOP(car operation panel)轿厢操纵盘copper铜cord ”绳索,芯线"corddrive "绳传动,(厅门)" ﻫcore 铁心corepress 铁心压力ﻫcore ventilation铁心通风ﻫcork 软木ﻫcork packing 软木盘根corner "角,隔"ﻫcorner post 对角立柱ﻫcorpus lift 尸体升降机ﻫcorrect phase seq uence正确相序correcting "修正,校正"correctingtravel 校准运行ﻫcorrection ”校正,校准"corrective maintenance 校正维修ﻫcorridor 走廊ﻫcorrosionproof防腐蚀得ﻫcorrosionresistant 耐腐蚀得ﻫcorrosionresistantcoating涂防锈漆层ﻫcorrosive腐蚀得ﻫcost ”成本,费用"cost accounting成倍核算ﻫcost analysis 成本分析ﻫcost calculation 成倍计算cost parison成本比较ﻫcost effective 价格划算得cost element 成本项目costestimate 成本估算cost of material 材料成本cost of production生产成本ﻫcost price成本价costshare 成本份额cost situation成本状况ﻫcost structure 成本结构ﻫcost—free免费得cotterpin 开口销counpler联轴器counter emf 反电动势ﻫcounterinductor 记数感应器ﻫcountersunkhead 埋头ﻫcounterbalance "相互平衡,配重平衡” ﻫcountersink "沉头,埋入” ﻫcounterweight ”对重装置,对重” counterweightbottom runby 对重底部越程counterweight filler ”对重块,对重装置重鉈"ﻫcounterweight fillerweight"对重块,对重装置重鉈” ﻫcounterweightframe 对重框counterweight guard 对重防护栏counterweight header对重头ﻫcounterweight housing 对重架counterweightsafety对重安全钳ﻫcounterweight sheave对重绳轮ﻫcounterweight sling对重吊具ﻫcounterweight top clearance对重装置顶部安全装置ﻫcountrewei ght suspension 对重悬挂装置ﻫcouple M to N 使M与N偶合coupleddoor panels 配对门扇ﻫcoupling 联轴器coupling bolt联轴器螺栓ﻫcoupling sleeve 联接套筒ﻫcove 凹口cover ”盖,保护层"coverplate盖板cover strip覆盖条ﻫcovered wire覆层线ﻫCPS(central processing system) 中央处理系统CPU(centralprocessingunit) 计算机中央处理器cr parking device轿厢驻停装置crack裂缝cracking pressure 破裂压力ﻫcrack—resistant抗裂得ﻫcradle beam ”托架,横梁" ﻫcrank曲轴crankoperation 曲轴操作ﻫcrank shaft 曲轴crank shaft oil seal 曲轴油封ﻫcreep”爬行,蠕动"ﻫcreep speed "爬行速度,平层速度"creeping-indistance 爬行距离Cremona's method谷式应力图ﻫcrest value 峰值crimp-mesheddoor铁网门ﻫcritical path planning关键路线计划法ﻫcross beam ”顶梁,上梁”cross head screwdriver 十字头螺丝功锥ﻫcross pin十字销cross valve 三通阀cross—head 上梁ﻫcross—headscrew十字头螺钉ﻫcrossheadsheave轿顶轮cross—section 横截面ﻫcrow bar 撬棒ﻫcrown bar 顶杆crown wheel盘形轮crushing "压碎,压溃"ﻫcup "杯,盖子"ﻫcup headsquare neckbolt半圆头方颈螺栓ﻫcurrent 电流ﻫcurrent carrying 带电得currentcarryingcapacity载流量current characteristic电流参数ﻫcurrent controlloop电流控制回路current efficiency 电流效率currentinterruptiontest 断流试验current load电流负荷currentreference signal 电流基准符号ﻫcurrentregulator”电流调节器,稳流器” current relay电流继电器currentreverser电流互感器currenttransformer 变流器curvature”曲率,曲度” ﻫcurve 曲线ﻫcurve transition 曲线过渡段cushion"垫,缓冲垫” ﻫcustom”习惯,海关"ﻫflush bolt平头螺栓flush door 嵌入式门ﻫflush mounted 找平安装ﻫflux 焊锡,磁通,稀释剂flux controlled 磁通控制得flyball governor 甩球式限速器ﻫflying wheel飞轮,惯性轮ﻫflywheel 飞轮ﻫflywheel effect飞轮效应,飞轮力矩flywheel mass 飞轮质量ﻫFMS(flexiblemanufacturing system) 挠性制造系统ﻫFOB(free on board)离岸价ﻫfoil薄膜ﻫfolder文件夹ﻫfolding door折叠式门,栅栏门folding gate 折叠式门,栅栏门ﻫfoolproof 防误操作得,十分安全得ﻫfoothold 立足处ﻫfoot -mounted motor 底座式电动机force 力force each-floor—stopoperation 每次强迫停止操作ﻫforced air cooling 强制风冷ﻫforc edconvection强迫通风ﻫforced ventilation 强迫通风ﻫforced-stop control 强迫停止控制foreman工头,领班forge锻造,锻压ﻫforging 锻,锻件fork lift 叉车ﻫforkspring 叉式弹簧ﻫfork type hydraulic elevator 间接侧置式液压梯formed anglesteel成型角钢formedchannel steel 成型槽钢formed steel 带钢ﻫformula 计算公式foundation 基础,机座ﻫfoundationbolt地脚螺栓ﻫfoundry铸造ﻫfourpaneldoor (双速)四扇门ﻫfour way traffic 四路交通four wire three phase三相四线ﻫfour-panel centeropeningdoor中分四扇门,双折中分门FPGA(field programmablel gate array)现场可编程门列阵ﻫFPLD(field programmable logic device)现场可编程逻辑器件fraction分数frame 构架ﻫframe counterweight 框架式对重ﻫframework框架ﻫfree car自由电梯freefall test 自由落体实验ﻫfree height净空高度free landing 自由基站ﻫfree maintenancecontract 免费维修保养合同ﻫfree wheel stop 滑行停车ﻫfree wheeling diode自振荡二极管ﻫfreezer elevator冷库梯ﻫfreghtlift 载货电梯freght rate 运费标准freight 货物freightcharge 运费ﻫfrequency频率frequencycontrolled调速得frequency inverter 变频器ﻫfrequencyjump 跳频friction 摩擦ﻫfrictionangle 摩擦角ﻫfriction clutch摩擦离合器ﻫfrictionforce 摩擦力front edge 前缘ﻫfront entrance 正面入口ﻫfront opening前开门ﻫfront panel轿箱前帮,前侧壁frontreturn 轿箱前帮,前侧壁ﻫfrontview 正视图ﻫfrontwall 前壁ﻫFRP(fiberreinforced plastics)纤维强化塑料fulcrum pin支点销ﻫfull car满载(满员)轿箱ﻫfull car by—pass 满员直驶(不停)ﻫful lload 满载full loadcurrent满载电流ﻫfull load torque满载力矩ﻫfullloaded car 满载(满员)轿箱ﻫfull maintenance 全面维修,全包维修ﻫfullmaintenance contract 全面维修合同full selective全集选(控制)ﻫfull up and down collective control上\\下全集选控制fullwarproping 全绕式(复绕式)挂绳ﻫfullwave rectifier全波整流器full wrap全绕,复绕full(up/down)collective control全(上\\下)集选控制ﻫfume 烟ﻫfunction 功能function description 功能说明ﻫfunction design功能设计ﻫfunction test功能试验ﻫfunicular缆车ﻫfuse 保险丝,熔丝fuseblown 保险丝烧断ﻫfuse box 保险丝盒fuse disconnectedswitch 熔断开关fuse holder熔断器座fuse protection熔断保护ﻫfuzzy logic 模糊逻辑ﻫGal(galileo)伽(重力加速度单位)Gal(gallon) 加仑(液量单位)galvanize 镀锌galvanized 镀锌得galvanizediron 镀锌铁皮galvanized steel镀锌钢ﻫgap间隙ﻫgarageelevator车库电梯ﻫgascutting 气割gasfilled充气得。
电梯专业英语词汇??abbreviation 缩语? abnormal "不正常的,反常的"? abnormality monitoring 异常监听? abrasion 磨损? abrasion resistant 耐磨性?abrasive cloth 砂布?absorb 吸收?absorber 减振器?AC drive 交流拖动?AC feedback control 交流反馈控制?AC motor 交流电机?AC servo 交流伺服?AC servo motor 交流伺服电机?AC single speed 交流单速?AC two speed 交流双速?AC two speed motor 交流双速电动机?AC variale speed 交流调速?AC(alternating current) 交流电?acanning cycle 扫描周期,扫描循环?acceleration control system 加速度控制系统?acceleration(accel)rate 加速器?accelerator 加速器?acceptance of lift 电梯验收?acceptance period 验收阶段?acceptance test 验收试验?acceptanec certificate 验收证书?access door 检修门?access forbidden 禁止入内?access lift 通道电梯?access security 通道防卫?access switch "通道开关,维修用开关"? access way 进出通道?accessibility "可通达性,接近的,难易程度"? accessible 允许进入?accessible space 允许进入的场地? accessory "配件,附件"?accident 事故?accident insurance 事故保险?accident prevention 事故预防? accidental contact 触电?accidental operation 误操作?accordion door 折叠门?accumulation 累积?accumulator 蓄电池?AC-GL machine 交流无齿曳引机? acoustic "听觉的,声音的"?acrew die 板牙?activate "启动,触发"?active mode 主动模式?actual condition "实际状况,实际条件"? actual load 实际载荷?actual state 实际状况?actual value 实际值?actuate "开动,操作,激励"?actuating linkege 操作连杆?actuating magnet 操作磁铁?actuation time 动作时间?actuator "操纵机构,激励器,螺线管"? actuator bracket 调节器支架actuator plate 调节板?ACVF drive 交流调频拖动?ACVF system 交流调频系统?ACVF(AC varible frequency) 交流调速? ACVV dirve 交流调压拖动?ACVV system 交流调压系统?ACVV(AC varible voltage) 交流调压? adaptation "适应,匹配"?adapter PCB 选通脉冲印刷电路板?adapter(adapator) 适配器?adapting 选配?adaptive control system 自适应能力控制系统? addendum "齿顶高,附录"?addendum circle 外圆?adding working drawing 附加加工图? addition "附加物,加法"?additional materials 附加材料?address 地址?adhesion "胶,粘合胶"?adhesion protective oil 防粘油?adhesive foil 胶粘薄膜?adhesive tape 胶带?adjacent 邻近的?adjacent car "相邻轿厢,相邻电梯"?adjacent entrance 相邻出入口?adjusment 调试?adjustable condensor 可变电容器? adjustable resistance 可调电阻?adjustable spanner 可调扳手?adjustable speed electric drive 调速电力拖动? adjustable wrench "活动扳手,可调扳手"? adjusting screw 调节螺丝?adjustor 调试员?administation overjhead rate 管理费用标准? administration cost 管理成本?administration expenses 管理费用?advance door opening 提前开门?advance payment 预付款?advanced "提前的,先进的"?advanced carriage 超前拖板(选层器)?advancing position reference value 超前位置参考值? aerial cableway "空中缆车,架空索道"?aerial ropeway "空中缆车,架空索道"?aerial tramway "空中缆车,架空索道"?aesthetic 美观?after sales service 售后服务?agency 代理?agenda 议程?air cord (门机用)航空钢丝绳?air purifier 空气滤清剂?air ventilator 通风管?air-bleed 空气分泄器?airborne noise 空气传播噪声?air-condition 空调?air-gap 气隙?alarm 警报?alarm bell 警铃?alarm button 警铃按钮?alarm buzzer 警报蜂鸣器?alarm circuit 警报电路?alarm system 警报系统ALC(autoclaved light-weight concrete) 蒸压轻质混凝土? alcove arrangement 电梯U型排列法?algorithm 算法规则系统?align 校正?aligning template 校正样板?alignment 校正?alignment gauge 校正量规?alkali 碱?all-computer-controlled 计算机全控的?allocation "分配,分派"?allocation of landing call 层站呼梯指令分配? allowance "允用误差,加工余量"?allowble stress for temporary load 允许暂时应力值? alloy 合金?alloy steel 合金钢?alteration 改进?alternate floor 隔层?alumina 氧化铝?aluminum 铝?aluminum alloy 铝合金?aluminum bronze 铝青铜?aluminum cladding 铝制包层?alumite 防蚀铝?alundum 氧化铝?ambient 环境的?ambient noise 环境噪音?ambient temperature 环境温度? ammeter 安培计?ammonia 氨?amperage 电流强度?ampere 安培?amplification 放大?amplification stage 放大等级?amplifier 放大器?amplifying tube 放大管?amplitude 幅度?analog adder 模拟加法器?analog computer 模拟计算机?analog speed card 模拟曲线板?analog-digital converter 模拟-数字转换器? analogue(analog) 模拟?analysis 分析?analysis mode 分析模拟?anchor bolt 地脚螺栓?anchorage "锚具,锚定"?angle bar 角钢?angle guide 角铁导轨?angle iron 角铁?angle iron frame 角铁框架?angle of contact 接触角?angle of deflection 导向角?angle of inclination 倾斜角?angle of lead 导程角?angle of traction 曳引机包角?angle of wrap 包角?angle steel 角钢?angular contact ball bearing 向心推力球轴承?angular contact bearing 角面接触滚动轴承?angular gear 斜齿轮?angular retardationg 角减速度?angular velocity 角速度?anneal 退火?annealing 退火?annual inspection 年检?annual report 年度报告?annunciator "报音器,声音合成器"?anode 阳极?anodize 氧极氧化?ANSI(America Nationa Standard Instirute) 美国国家标准协会? anti-clockwise 逆时钟方向?anti-corrosive paint 防腐蚀漆?anti-creep 防蠕动?anti-friction bearing 抗摩擦轴承?anti-nuisance 防干扰?anti-nuisance device 防捣乱装置?anti-phase braking 反向制动?anti-phase current 反相电流?anti-rebound of compensation rope device 补偿绳防跳装置? anti-residual 防剩磁?anti-resonance 抗谐振?anti-reversion device 防反转装置?anti-rust 防锈?anti-stall 防空转?anti-vibralion pad 防震垫?APM(automatic people mover) 自动人员运输机? apparen power 视在功率?apparent output 视在输出?applicant 申请人application 申请?application guide 应用指南?aprons 裙板?arbour "轴,杆"?arc chamber 电弧隔离室?arc protection 防电弧?arc quenching 熄焊弧?arc shield 电弧屏蔽?arc suppressor 灭焊器?architect 设计单位?architecture 建筑学?architrave 门框?area 面积?arm "臂,支路"?armature 电驱?armature coil 电驱线圈?armature current 电驱电流?armature lamination 电驱铁芯片?armature shaft 电驱轴?armature spider 星形轮?armature winding 电驱绕组?armoured 蛇皮管的?armoured cable 蛇皮管电缆?armoured conduit 导线管?arrangement 布置?arrival bell 到站铃?arrival buzer 到站蜂鸣器?arrival floor 到达楼层?arrival gong 到站钟?arrival rate 到站率?article of consumption 消耗品?artificial intelligence 人工智能?artistic 工艺?artistic face 工艺表面?asbestos packing 石棉盘根?ascending 上升?ASIC(application specific integrated circuit) 专用集成电路? assemble 装配?assembler language 汇编语言?assembly of hinge 铰链组装?assign 分配?astragal 装饰镶条?atmospheric influence 大气影响?attachment 附件?attendant control 有司机控制?attendant control compartment 有司机控制盒?attendant operation 有司机操作?audible signal 音响信号?audio tape recording 磁带录音?authority "当局,核准部门"?authority of lift acceptance 电梯验收部门?authorized "授权的,核准的"?authorized user 核准使用者?auto-adaptation 自适用?AutoCAD 自动计算机辅助设计?autographic recoder 自动记录仪?automatic 自动的?automatic allocator 自动分派器?automatic by-pass 自动直驶?automatic center opening sliding door 自动中分式滑动门?automatic closer 自动关闭门?automatic dispatch 自动调度?automatic door 自动门?automatic homing 自动回基层?automatic landing 自动停站?automatic landing system by spare battery 靠备用蓄电池的自动停站设备? automatic leveling 自动平层?automatic lubricator 自动润滑装置?automatic parking garage 自动停车库?automatic parking system 自动停车系统?automatic relevelling 自动平层校正?automatic rescue device 应急救助装置?automatic return 自动返回?automatic telescopic center opening sliding door 自动中分式折叠滑动门? automatic telescopic sliding door 自动折叠式滑动门?automobile lift 汽车电梯?autowalk 自动人行道?auxiliary apparatus 辅助装置?auxiliary brake 辅助制动器?auxiliary cicuit 辅助电路?auxiliary contact 辅助触点?auxiliary drive 辅助驱动?auxiliary lock 辅助锁?auxiliary materials 辅助量?auxiliary value 辅助材料?auxiliary winding 辅助绕组?available area 有效面积?average 平均?average car load 平均轿厢负载?average dispatching interval 平均调度间隔时间? average interval 平均调度间隔时间?average passenger waiting time 平均乘客侯梯时间? average response time 平均应答时间?average waiting quest 平均乘客量?average waiting time 平均乘客侯梯时间?axial flow fan 轴流式风扇?axis 轴线?axle 轴babbit 巴氏合金?babbit lined bearing 巴氏合金衬里轴承?babbit melter 巴氏合金熔化器?babbit metal 巴氏合金?babbit rope socket 灌注式巴氏合金绳头?back current 反向电流?back 反电动势?back lash 轮齿隙?back plunger type 后部柱塞式(液压梯)?back side "后侧,后边"?back type governor 轴流式限速器?back wall 后壁?baked enamel 烤漆?balace weight 平衡器?balance 平衡?balance chain 平衡链?balance coefficient 平衡系数? balanced traffic 平衡交通?ball bearing 滚珠轴承?ball cup 球形碗?ball pin 球形硝?ball stop valve 球形断流器?ball type bearing 滚珠轴承?ballast 镇流器?balustrade deching 外侧盖板? balustrade exterior panelling 外装饰板? balustrade lighting 扶手照明? balustrade panel 扶手板?balustrade skirting 扶手群板? balustrades 扶手装置?bandsaw 带锯?bank "银行,群组,排"?bar "条,棒"?bar code 条形码?bar lock 杆式锁?bare wire 裸线?barricade "防护墙,隔墙"?barrier "隔板,栅栏"?base "基座,基础"?base plate 基板?basement 地下室?basement service 底下室服务? basement type 底吊式?basic logic element 基础逻辑元件?basic logic function 基础逻辑功能?batch production 批量生产?battery 电池?battery- backed 电池支持的?battery box 蓄电池箱?battery charger 电池充电器?baud rate 波特率?BCD(binary coded decimal) 二进制编码的十进制? beam 梁?beam pad 井道内电缆保护垫片?beam pulley 抗绳轮?bearing 轴承?bearing bracket 轴承支架?bearing cap 轴承盖?bearing load 轴承负荷?bearing plate 承重板?bearing play 轴承间隙?bearing sleeve 轴承衬套?bearing stand 轴承座?bed lift 病床电梯?bed plate 底座?bell 铃?belt 胶带?belt drive 胶带传动?belt grinder 胶带磨床?belt pulley 胶带轮?belt type moving walk 带式自动人行道?bending 弯曲?bending stress 弯曲应力?benzine 轻汽油?bevel gear 伞(斜)齿轮?beveled washer 斜垫圈?BGM (background music) 背景音乐? BGM speaker 背景音乐扬声器?bias "偏置,偏移"?bid "投标,报价"?bid table 报价单?bidder 投标?bidding cycle 投标有效期限?bidding procedure 投标(报价)程序?bil of delivery 发货单?bil of lading 海运提单?bill of expenses 费用帐单?bill of materials 材料单?billing 开发票?binary 二进制?binder 装订册?bi-parting 对开式(上下开启)?bi-parting door 垂直中分门?bipartite light transistor 双分式光电管? bistable magnetic swich 双稳态磁开关? bistable switch 双稳态磁开关bitumen 沥青?blade "叶片,刀片,锯片"?blade connector 刀形连接器?bleed-off circuit 泄放电路?blind hoistway 盲(无门)井道?block chart 方框图?block diagram 方框图线路?block of flats 住宅楼区?blocking of control circuit 控制电路闭锁? blower 鼓风机?blower coil 吹弧线圈?blower motor 风机电动机?blue print 蓝图?boading floor 登梯楼层?boading time 登梯时间?boarding 登梯?boarding landing 登梯层站?boarding passenger 登梯乘客boarding rate 登梯率?boarding stop 登梯停站?boarding zone 登梯区域?bobbing 绕线管?boldface type 粗字体?bolt 螺杆?booster 升压机?border condition 边界条件?bore hole "钻孔,镗孔"?boring 镗?boring lathe 镗床?boring machine 镗床?boring miller 镗铣床?bottom 底部?bottom car clearance 轿底安全高度间隙? bottom car overtravel 底部轿厢越程?bottom car runby 底部轿厢越程?bottom clearances for car 轿底间隙?bottom counterweight clearance 轿底对重间隙? bottom counterweight overtravel 轿底对重越程? bottom counterweight runby 轿底对重越程? bottom door retainer 门下角?bottom floor 底部楼层?bottom runby 底部越程?bottom slow down switch 底部减速开关? bottom stop 底部停战?bottom terminal floor 底部楼层?bottom terminal landing 底部端站?bottom terminal stop 底端停站?box "盒,箱"?box counterweight 箱式对重?Braille 盲文字符?brake 制动器?brake arm 制动器臂?brake contact 制动器触点?brake coutact 制动器联轴器?brake dish 制动盘?brake drum 制动轮?brake energy 制动力?brake level 制动器杠杆?brake lever 制动器手柄?brake lining 制动器衬套?brake linkage 制动器连杆?brake operater switch 制动操纵开关?brake pin 制动器悄?brake press "折弯机,压弯机"?brake pulley 制动轮?brake release lever 制动器松闸手柄? brake release magnet 制动器送闸磁铁? brake release time 制动器松闸时间brake shoe 制动靴?brake spacing 制动器间距?brake spring 制动弹簧?brake tension 制动器张紧力?brake torque 制动器力矩?brake wrench 制动器板手?braking 制动?braking distance 制动距离?braking force 制动力?branch circuit 分支电路?brass founder 铸铜?break "切断,破断"?break-down 故障?breaking load 破断负荷?breaking strength 破断强度? breaking test 破坏实验?breather 通气管?brick 砖?brick-layer 砖砌工?bridge circuit 桥式电路?bridge connector 桥接器?bridge jumper 桥接片?bridge rectifier 桥式整流器?bright controlling 光度控制?broach 拉力?broaching machine 拉床?brochure 手册?broken chain contact 断链触点?broken circuit 断路?broken drive chain contact 主驱动链保护装置? broken drive-chain safety device 驱动链条保护装置? broken rope contact 驱动链条列断安全装置? broken step chain contact 断绳触点?broken step chain device 断绳开关?broken step chain safety device 梯级链断列触点? broken step safety device 梯级破列安全装置? broken tape sweitch 短带开关?bronze 铜?brunching "成组,成群"?brush finished stainless steel 哑光不锈钢?brush holder "刷握,滑环"?brush yoke 刷架?budget 预算?buffer 缓冲器?buffer base 缓冲器底座?buffer plate 缓冲器板?buffer plunger 缓冲器柱塞?buffer return spring 缓冲器复位弹簧?buffer stand 缓冲器台?buffer striking plate 缓冲器撞板?buffer stroke 缓冲器冲程?buffer support 缓冲器支承?buffer switch 缓冲器开关?buider's work drawing 土建图纸?buiding facility 大楼设施?buiding supervision center 大楼监管中心?builder 建筑单位?building 建筑?building area 建筑面积?building contractor 建筑承包商?building manager 大楼管理者?building monitoring and security system 大楼监管和安全系统? building population 大楼居住人口?built=in 内装?built-in escalator 组合式自动扶梯?bumper 弹簧式缓冲器?bumper rail 防撞板?bumpy ride 颠簸振动的运行?buried 埋入的?burn in (程序)灌入?burr "毛刺,毛边"?burr free 去毛刺?bus 总线?bus bar 汇流条?bush 衬套?bushed bearing 加衬轴套?bushing "衬套,轴套,套筒"?butt joint "平接,对焊"?button 按钮?button switch 按钮开关?buyer 买方?buzzer 蜂鸣器?buzzer switch 蜂鸣器开关? bypass 直驶?by-pass button 直驶按钮?by-pass valve 溢流阀? bypassed floor 直驶不停楼层? bypassed stop 直驶不停层站C$F 到岸价?cab "轿厢,座舱"?cab interior 轿厢内部?cabin "轿厢,座舱"?cabinet "柜,厢"?cable 电缆?cable box 电缆箱?cable car 缆车?cable cleat 电缆夹具?cable conductor 电缆导线? cable entry 电缆引入?cable hanger 电缆吊架? cable hole 电缆孔?cable joint 电缆接头?cable termination 电缆末端? cable trunk 电缆接头?CAD 计算机辅助设计?cage 轿厢?cage door 轿厢门? calculation 计算机辅助设计? calibrate 校准?call "呼梯,呼叫"?call acceptance 呼梯接收?call accepted 接受呼梯?call accepted indicator 接受呼梯指示灯? call accepted signal 接受呼梯信号?call allocation 呼梯分派?call assignment 呼梯指令分配?call band 呼梯信号带?call button 呼梯按钮?call cancel 呼梯取消?call canceling 呼梯取消?call coincidence 呼梯重合?call conmting system 呼梯计数系统?call contrl 呼梯指令控制?call emitter 呼梯指令发送器?call input 呼梯输入?call input capacity 呼梯输入内容?call input device 呼梯输入装置?call load 呼梯输入?call memory 呼梯记忆?call registered 登陆的呼梯?call registered signal 登陆的呼梯信号? call registration indicator 呼梯登陆信号? call sequence 呼梯顺序?call tegistration 呼梯登陆?call-back 召修?call-back message 召修信息?callinfg board 召唤盒?calling floor 呼体楼层?calling landing 呼梯?call-out response time 维修召唤应答时间?call-out service 急修服务?CAM 计算机辅助制造?cam 凸轮?cam for positive operation 强制操纵凸轮? cam lever 偏心柄?cam shaft 偏心轴?cam tape control 偏心带控制?cam-gear 凸轮传动装置?cam-operated switch 凸轮(碰铁)操纵开关? cancel "撤消,取消"?cancelingof call signal 呼梯信号消除? cancellation "撤消,取消"?canopy "顶盖,大蓬"?canvas 帆布?canvas hose 帆布软管?cap "帽,盖子"?cap nut 螺母?capacitance "电容,电容量"?capacitor 电容?capacitor motor 电容器电机?capacity "载重,容量,定员"?capacity plate 载量标牌?capstan 绞盘?captive roller safety gear 滚柱式安全钳? car 轿厢?car annunciator 轿厢报警器?car approaching gong 轿厢到站预报钟? car apron 轿厢入口群板?car assignment "轿厢调度,轿厢分配"?car automatic switch landing 轿厢开关自动停站? car axis 轿厢中心线?car back wall 轿厢后壁?car botom clearance 轿厢安全高度?car bottom overtravel 轿厢底部越层?car bottom runby 底部越程?car buffer 轿厢缓冲器?car button 轿厢按钮?car cab 轿厢体?car call 轿厢指令?car call button 轿厢指令按钮?car call cancel 轿内召唤取消?car call control 轿厢指令控制?car call panel 轿厢(呼梯)指示盘?car call stop 轿厢(呼梯)指令停车?car cam 碰铁?car canopy 轿厢顶盖?car ceiling 轿厢装饰顶?car coming indicator 轿厢驶近指示灯?car control lever 轿厢操纵手柄?car control switch 轿厢操纵开关?car counterweight 轿厢对重?car cross-head 轿厢上梁?car depth 轿厢深度?car dispatch 轿厢调度?car door 轿门?car door catch 轿门栓?car door closer 轿门关闭器?car door electric contact 轿门电触点?car door guide shoe 轿门导靴?car door interlock 轿门联锁?car door lock 轿门门锁?car door rail 轿门导轨?car door sill 轿门地坎?car door track 轿门导轨?car elevator 汽车电梯?car emergency exit "轿厢安全门,应急门"?car emergency opening 轿厢安全窗?car emergency release switch 轿厢应急释放按钮? car enclosure panel 轿厢壁板?car enclosures 轿厢壁板?car entrance 轿厢入口?car extetior "轿厢外装修,轿厢外表"?car fan 轿厢风扇?car floating movable platform 轿厢活动地板?car floor frame "轿厢架,轿架"?car frame "轿厢架,轿架"?car frame attachment 轿厢框架附件?car frame plank 轿厢下梁?car frame upright 轿厢立柱?car front 轿厢前壁?car full control 满载轿厢控制?car gate 轿厢门?car gate contact 轿门触点?car gate electric contact 轿门电气触点?car guide 轿厢导轨?car guide axis 轿厢导轨中心线?car handle control "手柄开关操纵,轿内开关控制"?car handrail 轿厢扶手?car height 轿厢高度?car illumination 轿厢照明?car isolation 轿厢隔震器?car leveling device 轿厢平层装置?car lift 汽车电梯?car light 轿厢照明装置?car light panel "轿厢照明板,照明天花板"?car lighting 轿厢照明?car manual switch landing 轿厢手动开关停站?car operation board 轿厢操纵盘?car operation panel 操纵箱?car overload 轿厢超载?car panel 轿厢壁板?car panel attachment 轿厢壁板附件?car panel base 轿厢壁板底座?car panel with window 轿厢壁板上窗口?car platform "轿厢底,轿底"?car platform guard 轿厢站台护板?car platform sill 轿厢?car position indicator "轿厢指示灯,轿厢位置显示"? car position reference value 轿厢位置参考值?car preference 轿厢优先权?car push-button 轿厢按钮?car rear wall 轿厢后壁?car roof "轿厢顶,轿顶"?car safety 轿厢安全钳?car safety bar for dumbwaiter 轿厢安全棒(杂货梯)? car safety gear 轿厢安全钳?car safety mechanism switch 轿厢安全钳联动开关?car sheave 轿厢绳轮?car side emergency door 轿厢安全侧门?car side opening 轿厢侧面开门?car side wall 轿厢侧壁?car sill 轿厢地坎?car sling "轿厢架,吊架"?car station 轿厢操纵站?car status information 轿厢运行状态信息?car stop 轿厢停止?car suspension 轿厢悬挂装置?car switch 轿厢开关?car switch automatic floor stop operation 轿厢开关自动停站装置? car switch control 轿厢开关控制?car switch opration "手柄开关操纵,轿内开关控制"?car top 轿厢顶部?car top clearance 轿顶安全高度?car top emergency exit "轿顶安全出口,轿顶应急出口"?car top guard 轿顶护栏?car top inspection device 轿顶检修装置?car top inspection station 轿顶检修盒(站)?car top light 轿顶照明装置?car top protection balustrade 轿顶防护栏杆?car top protection railing 轿顶防护栏杆?car ventilation 轿厢通风?car walls "轿厢壁,轿壁"?car weight 轿厢重量?car width 轿厢宽度?carbon "碳,石墨"?carbon brush 碳刷?carbon contact 碳精触点?carbon steel 碳素钢?carburization 渗碳?carburize 渗碳?carburized hardening 渗碳硬化? carburizer 渗碳剂?card "卡片,纹板"?card reader 卡片读出器?cardan joint 万向接头?carpet 地毯?carriage charges 运费?carry frequency "载波频率,开关工作频率"? carrying capacity "载运量,载运能力"?cart elevator 车辆运货电梯?cartridge fuse 插塞式熔断器carving machine 刻模机?cascade "级联,串联"?cascade sub-loop 串接式子回路?case "箱,盒,外壳"?casing "保护套,外套"?casing of cylinder 油缸套?cassette tape 录音带?cast bronze 铸青铜?cast iron 铸铁?cast steel 铸钢?casting 铸造?castor oil 蓖麻油?catch "擎子,门扣,捕捉器"?catch block 安全钳?catch clip 捕捉夹钳?catch device 捕捉装置?cathode 阴极?cathode ray tube(CRT) 阴极射线管?cavitation "气穴,涡穴,饱和压力点"?ceiling 吊顶?ceiling assembling 轿顶?cellulose 纤维板?cement "水泥,胶合剂"?cement concrete 混凝土?cenrifugal brake 离心制动器?center 中心?center latch 中心门栓?center line 中心线?center of curvature 曲率中心?center opening 中分式门?center opening door 中分门?center opening two speed door 中分四扇门?center opening vertical sliding door 中分式垂直滑动门? center plunger hydraulic lift 柱塞直顶式液压电梯? center support "中心支撑,中间支撑,第三支撑"?center-opening folding door 中分式折叠门? centigrade 摄氏温度?central alarm 中央报警?central control board 中央监控盘?central control room 中央监控室?central jack 中心液压装置?central position 中心位置?centrifugal 离心的?centrifugal cast 离心铸造?centrifugal fan 离心式风扇? centrifugal governor 离心式限速器? centrifugal speed 离心速度? centrifugal switch 离心开关? centrifugal type governor 离心式限速器? centripetal force 向心力?ceramic capacitor 搪瓷电容? certification 证书?certifying body 认证机关?chain 链条?chain block 手拉葫芦?chain bracket 链条托架?chain drive 链传动?chain drive elevator 链驱动升降机? chain drive machine 链驱动机?chain gear 链轮?chain guard 链防护罩?chain link "链节,链环"?chain pitch 链条节距?chain sag 链条下垂度?chain sheave 链轮?chain sprocket 链轮?chain sustarned elevator 链支撑升降机? chain tensioning device 链张紧装置? chain wheel 链轮?chain wheel track 链轮导轨?chamger "倒棱,去毛刺"?change switch 转换开关?change-over contact 转化触点? change-over landing 换乘电梯层站? change-over switch 转换开关? change-pole 变化极性?channel 槽钢?channel iron 槽铁?channel steel 槽钢?character "特征,字符"? characteristic "特征,特性"? characteristic curve 特性曲线? charge "充电,收费"?charged "带电,充电"?charging contactor 充电接触器? charging set 充电?chart 图表?chart of accounts 成本图表?check valve 止逆阀?chequer(checker)plate 网纹钢板? chief engineer 总工程师?chime 音钟?chip 芯片?chipboard 木屑板?chisel 凿子?choke "扼流,截流,阻塞"?choke coil 扼流线圈?chopper 斩波器?chrome 铬?chuck 卡盘?CIF(cost insurance and freight) 到岸价? cinder concrete 煤渣混凝土?circle "周期,圆"?circuit 电路?circuit breaker "断电器,断路器"?circuit diagram 电路图?circular pitch 周节?circulating pump 循环泵?circulation 循环?circumferential force 圆周力? circumferential speed 圆周速度? circumferential velocity 圆周速度?CL(center line) 中心线?clacking 盖板?cladding 装饰?clamp 夹?clamp ring "压制环,加紧环"?clamping jaw 夹钳?clamping sleeve 夹紧套桶?clamping strap 制动带?class of loading 灾荷种类?clear depth 净深度?clear dimension 净尺寸?clear door height 门净高度?clear door width 门净宽度?clear entrance to the car 轿厢入口净尺寸? clear height 净高?clear hoistway 井道净尺寸?clear width 净宽度?clearance between skirt panels 裙板间隙? clearance bottom car 轿底安全高度?clearance top car 轿顶安全高度?clearance top counterweight 对重装置顶部安全高度? cleated riser 梯级竖板?clerance 间隙?clevis U型夹?client "客户,买主"?clip 钳夹?clockwise 顺时针的?close circuit 闭合电路?closed loop 闭环?closed position (门)关闭位置?closed position monitoring (门)关闭位置检测? closed-loop control 闭环控制?closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing travel 门关闭运行closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体)CNC(computerized numric control) 计算机数控coast to stop 滑行停车coaxial cable 同轴电缆cock 龙头code "码,符号,规程,规范"code of practice "实施规程,实用规程"code word 代号文字coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数coefficient of friction 摩擦系数coil "线圈,绕组"coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate "栅栏门,折叠式门"collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection "收集,集合"collective control 集中控制collective full automatic operation 全自动集中控制collective operation elevator 集中操作电梯collective selective 集选collective selective control 集选控制collector 集电路collision switch 碰撞开关colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column "柱,立柱"comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment "隔板,隔室"compennsating device for hoist ropes 曳引绳补偿装置compensanting/equalizer disk 补偿/补偿器compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent "有资格的,胜任的"competent personnel "有资格的人员,胜任的人员"competitor system 竞争机制component 部件compound wind motor 复励电动机compound wound 复绕comprehensive 综合的comprehensive maintenance contract "综合维修合同,全包维修合同" comprehensive service contract "综合维修合同,全包维修合同" compressing spring 压缩弹簧compression 压缩compression switch 压缩开关compressive stress 压应力compressor 压缩器compulogic system 电脑程序控制系统computer 计算机computer peripheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed "隐蔽的,暗式"concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod "连杆,连接杆"connection 连接connection diagram of controller 控制柜连线图connector "接线柱,连接器"conract specification "合同规定,合同明细表" conract speed "合同速度,额定速度" consecutively departing 依次派出的轿厢console panel "控制柜,控制盘"constant "恒定的,常数"constant HP motor 功率恒定型电机constant speed valve "比例控制阀,调速阀" constant torque motor 力矩恒定型电机construction "安装,施工"construction crane 建筑起重机construction layout drawing 土建图construction platform "安装平台,施工平台" construction site "安装工地,施工工地" consultant "顾问,咨询机构"consumption 消耗contact 触点contact angle 接触角contact brace 触头撑条contact burning 触头烧损contact carrier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger "接触指,滑触头"contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷contact mat 触头垫片contact normally closed 常闭触点。
电梯汉英词汇电梯汉英词汇本表据《中国电梯标准》整理:电梯 LIFT;ELEVATOR乘客电梯PASSENGER LIFT载货电梯GOODS LIFT;FREIGHT LIFT客货电梯PASSENGER-GOODS LIFT病床电梯;医用电梯 BED LIFT住宅电梯 RESIDENTIAL LIFT杂物电梯 DUMBWAITER LIFT; SERVICE LIFT船用电梯 LIFT ON SHIPS观光电梯PANORAMIC LIFT;OBSERTION LIFT汽车电梯 MOTOR VEHICLE LLIFT;AUTOMBILE LIFT液压电梯 HYRAULIC LIFT平层准确度过 LEVELING ACCURACY电梯额定速度 RATED SPEED OF LIFT检修速度 INSPECTION SPEED额定载重量 RATED LOAD;RATED CAPACITY电梯提升高度 TRA VELING HEIGHT OF LIFT;LIFTING HEIGHT OF LIFT机房高度MACHINE ROOM HEIGHT机房宽度 MACHINE ROOM HEIGHT机房宽度 MACHINE ROOM DEPTH机房面积 MACHINE ROOM AREA辅助机房 SECONDARY MACHINE ROOM ;隔层SECONDARY FLOOR滑轮间隔 PULLEY ROOM层站台票LANDING层站入口 LANDING ENTRANCE基站 MAIN LANDING;MAIN FLOOR;HOME LANDING预定基站 PREDETERMINED LANDING底层端站 BOTTOM TERMINAL LANDING顶层端站 TOP TERMINAL LANDING层间距离 FLOOR TO FLOOR DISTANCE;INTERFLOOR DISTANCE井道WELL;SHAFT;HOISTWAY单梯井道 SINGLE WELL多梯井道 MULTIPLE WELL;COMMON WELL井道壁 WELL ENCLOSURE; SHAFT WELL井道宽度 WELL WIDTH;SHAFT WIDTH井道深度 WELL DEPTH;SHAFT DEPTH底坑PIT底坑深度 PIT DEPTH顶层高度 HEADROOM HEIGHT;HEIGHT ABOVE THE HIGHEST LEVEL SERVED;TOP HEIGHT井道内牛腿;加腋梁 HAUNCHED BEAM围井 TRUNK围井出口 HATCH开锁区域 UNLOCKING ZONE平层 LEVELING平层区 LEVELING ZONE开门宽度 DOOR OPENINGWIDTH轿厢入口 CAR ENTRANCE轿厢入口净尺寸 CLEAR ENTRANCE TO THE CAR轿厢宽度CAR WIDTH轿厢深度 CAR DEPTH轿厢高度 CAR HEIGHT电梯司机LIFT ATTENDANT乘客人数 NUMBER OF PASSENGER油压缓冲器工作行程 WORKING STROKE OF OIL BUFFER弹簧缓冲器工作行程 WORKING STROKE OF SRING BUFFER轿底间隙 BOTTOM CLEANCES FOR CAR轿顶间隙 TOP CLEARANCES FOR COUNTERWEIGHT对重装置顶部间隙 TOP CLEARANCES FOR COUNTERXEIGHT 对接操作规程DOCKING OPERATION隔层停*操作 SKIP-STOP OPERA TION检修操作规程 INSPECTION OPERATION电梯拽引型式TRACTION TYPES OF LIFT电梯拽引机绳拽引 HOIST ROPES RATIO OF LIFT消防服务FIREMAN SERVICE独立操作INDEPENDENT OPERATION缓冲器 BUFFER油压缓冲器(耗能型缓冲器) HYDRAULIC BUFFER;OIL BUFFER 弹簧缓冲器;蓄能型缓冲器具SPRING BUFFER减振器具VIBRATING ABSORBER轿厢CAR LIFT CAR轿厢底;轿底CAR PLATRORM;PLATFORM轿厢壁;轿壁 CAR ENCLOSURES;CAR W ALLS轿车厢顶;轿顶 CAR ROOR轿厢装饰顶 CAR HANDRAIL轿厢扶手CAR HANDRAIL轿顶防护栏杆 CAR PROTECTION BALUSTADE轿厢架;轿架 CAR FRAME检修门 DOOR OPERATOR检修门 ACCESS DOOR手动门 MANUALL Y OPERATED DOOR自动门POWER OPERA TED DOOR层门;厅门 LANDING DOOR;SHAFT DOOR;HALL DOOR防火层门;防火门 RIER-PROOF DOOR轿厢门;轿门CAR DOOR安全触板 SAFETY EDGES FOR DOOR铰链门;外敞门 HINGED DOOR栅栏门 COLLAPSIBLE DOOR水平滑动门 HORIZONTALL Y SLIDING DOOR中分门 CENTER OPENING DOOR旁开门 TWO-SPEED SLIDING DOOR双折门 TWO-PANEL SLIDING DOOR双速门 TWO SPEED DOOR左开门 LEFT HAND TWO SPEED SLIDING DOOR右开门 RIGHT HAND TWO SPEED SLIDING DOOR垂直滑动门VERTICALL Y SLIDING DOOR垂直中分门BI-PARTING DOOR拽引绳补偿装置 COMPENSATING DEVICE FOR HOIST ROPES补偿绳装置 COMPENSATING ROPE DEVICE补偿绳防跳装置ANTI-REBOUND OF COMPENSATION ROPE DEVICE 地坎 SILL轿厢地坎 CAR SILLS;PLATE THRESHOLD ELEVATOR层门地坎 LANDING SILLS;SILL ELEVATOR ENTEANCE轿顶检修装置 INSPECTION DEVICE ON TOP OF THE CAR轿顶照明装置 CAR TOP LIGHT底坑检修照明装置 LIGHT DEVICE OF PIT INSPECTION轿厢内指层灯;轿厢位置指示 CAR POSITION INDICATOR层门门套 LANDING DOOR JAMB层门指示灯 LANDING INDICATOR;HALL POSITION INDICATOR层门方向指示灯 LANDING DIRECTION INDICATOR控制屏 CONTROL PANEL控制柜 CONTROL CABINET;CONTROLLER操纵箱 OPERATION PANEL操纵盘 CAR OPERATION PANEL警铃按钮 ALARM BUTTON。
电梯专业英语词典全集A1abbreviation 缩语abnormal 不正常的,反常的abnormality monitoring 异常监听abrasion 磨损abrasion resistant 耐磨性abrasive cloth 砂布absorb 吸收absorber 减振器AC(alternating current) 交流电AC drive 交流拖动AC feedback control 交流反馈控制AC motor 交流电机AC servo 交流伺服AC servo motor 交流伺服电机AC single speed 交流单速2AC two speed 交流双速AC two speed motor 交流双速电动机AC variale speed 交流调速AC-GL machine 交流无齿曳引机acceleration(accel)rate 加速器acceleration control system 加速度控制系统accelerator 加速器acceptanec certificate 验收证书acceptance of lift 电梯验收acceptance period 验收阶段acceptance test 验收试验access forbidden 禁止入access door 检修门access lift 通道电梯3access security 通道防卫access switch 通道开关,维修用开关access way 进出通道accessibility 可通达性,接近的,难易程度accessible 允许进入accessible space 允许进入的场地accessory 配件,附件accident 事故accident insurance 事故保险accident prevention 事故预防accidental contact 触电accidental operation 误操作accordion door 折叠门accumulation 累积4accumulator 蓄电池acoustic 听觉的,声音的activate 启动,触发active mode 主动模式actual condition 实际状况,实际条件actual load 实际载荷actual state 实际状况actual value 实际值actuate 开动,操作,激励actuating magnet 操作磁铁actuating linkege 操作连杆actuation time 动作时间actuator 操纵机构,激励器,螺线管actuator bracket 调节器支架actuator plate 调节板ACVF(AC varible frequency) 交流调速5ACVF drive 交流调频拖动ACVF system 交流调频系统ACVV(AC varible voltage) 交流调压ACVV dirve 交流调压拖动ACVV system 交流调压系统adaptation 适应,匹配adapter(adapator) 适配器adapter PCB 选通脉冲印刷电路板adapting 选配adaptive control system 自适应能力控制系统addendum 齿顶高,附录addendum circle 外圆adding working drawing 附加加工图addition 附加物,加法additional materials 附加材料address 地址6adhesion 胶,粘合胶adhesion protective oil 防粘油adhesive foil 胶粘薄膜adhesive tape 胶带adjacent 邻近的adjacent car 相邻轿厢,相邻电梯adjacent entrance 相邻出入口adjustable condensor 可变电容器adjustable resistance 可调电阻adjustable spanner 可调扳手adjustable speed electric drive 调速电力拖动adjustable wrench 活动扳手,可调扳手adjusting screw 调节螺丝adjusment 调试adjustor 调试员7administration cost 管理成本administration expenses 管理费用administation overjhead rate 管理费用标准advance door opening 提前开门advance payment 预付款advanced 提前的,先进的advanced carriage 超前拖板(选层器) advancing position reference value 超前位置参考值aerial cableway 空中缆车,架空索道aerial ropeway 空中缆车,架空索道aerial tramway 空中缆车,架空索道aesthetic 美观after sales service 售后服务agency 代理8agenda 议程air cord (门机用)航空钢丝绳air purifier 空气滤清剂air ventilator 通风管air-bleed 空气分泄器air-condition 空调air-gap 气隙airborne noise 空气传播噪声alarm 警报alarm bell 警铃alarm button 警铃按钮alarm buzzer 警报蜂鸣器alarm circuit 警报电路alarm system 警报系统alcove arrangement 电梯U型排列法ALC(autoclaved light-weight concrete) 蒸压轻质混凝土9algorithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignment gauge 校正量规alkali 碱all-computer-controlled 计算机全控的allocation 分配,分派allocation of landing call 层站呼梯指令分配allowble stress for temporary load 允许暂时应力值allowance 允用误差,加工余量alloy 合金alloy steel 合金钢10alteration 改进alternate floor 隔层alumina 氧化铝aluminum 铝aluminum alloy 铝合金aluminum bronze 铝青铜aluminum cladding 铝制包层alumite 防蚀铝alundum 氧化铝ambient 环境的ambient noise 环境噪音ambient temperature 环境温度ammeter 安培计ammonia 氨amperage 电流强度ampere 安培amplification 放大11amplification stage 放大等级amplifier 放大器amplifying tube 放大管amplitude 幅度analogue(analog) 模拟analog adder 模拟加法器analog computer 模拟计算机analog speed card 模拟曲线板analog-digital converter 模拟-数字转换器analysis 分析analysis mode 分析模拟anchor bolt 地脚螺栓anchorage 锚具,锚定angle bar 角钢angle guide 角铁导轨angle iron 角铁angle iron frame 角铁框架12angle of contact 接触角angle of deflection 导向角angle of inclination 倾斜角angle of lead 导程角angle of traction 曳引机包角angle of wrap 包角angle steel 角钢angular contact ball bearing 向心推力球轴承angular contact bearing 角面接触滚动轴承angular gear 斜齿轮angular retardationg 角减速度angular velocity 角速度anneal 退火annealing 退火annual inspection 年检13annual report 年度报告annunciator 报音器,声音合成器anode 阳极anodize 氧极氧化ANSI(America Nationa Standard Instirute) 美国国家标准协会anti-clockwise 逆时钟方向anti-corrosive paint 防腐蚀漆anti-creep 防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰anti-nuisance device 防捣乱装置anti-phase braking 反向制动anti-phase current 反相电流anti-rebound of compensation rope device 补偿绳防跳装置14anti-residual 防剩磁anti-resonance 抗谐振anti-reversion device 防反转装置anti-rust 防锈anti-stall 防空转anti-vibralion pad 防震垫APM(automatic people mover) 自动人员运输机apparent output 视在输出apparen power 视在功率applicant 申请人application 申请application guide 应用指南aprons 裙板arbour 轴,杆arc chamber 电弧隔离室15arc protection 防电弧arc quenching 熄焊弧arc shield 电弧屏蔽arc suppressor 灭焊器architect 设计单位architecture 建筑学architrave 门框area 面积arm 臂,支路armature 电驱armature coil 电驱线圈armature current 电驱电流armature lamination 电驱铁芯片armature shaft 电驱轴armature spider 星形轮armature winding 电驱绕组16 armoured 蛇皮管的armoured cable 蛇皮管电缆armoured conduit 导线管arrangement 布置arrival bell 到站铃arrival buzer 到站蜂鸣器arrival floor 到达楼层arrival gong 到站钟arrival rate 到站率article of consumption 消耗品artificial intelligence 人工智能artistic 工艺artistic face 工艺表面asbestos packing 石棉盘根ascending 上升ASIC(application specific integrated circuit) 专用集成电路17assemble 装配assembler language 汇编语言ssembly drawing 组装图assembly of hinge 铰链组装assign 分配astragal 装饰镶条atmospheric influence 大气影响attachment 附件attendant control 有司机控制attendant control compartment 有司机控制盒attendant operation 有司机操作audible signal 音响信号sudible signaling system 音响信号系统audio tape recording 磁带录音authority 当局,核准部门18authority of lift acceptance 电梯验收部门authorized 授权的,核准的authorized user 核准使用者auto-adaptation 自适用AutoCAD 自动计算机辅助设计autographic recoder 自动记录仪automatic 自动的automatic allocator 自动分派器automatic by-pass 自动直驶automatic center opening sliding door 自动中分式滑动门automatic closer 自动关闭门automatic dispatch 自动调度automatic door 自动门automatic homing 自动回基层19automatic landing 自动停站automatic landing system by spare battery 靠备用蓄电池的自动停站设备automatic leveling 自动平层automatic lubricator 自动润滑装置automatic parking garage 自动停车库automatic parking system 自动停车系统automatic relevelling 自动平层校正automatic rescue device 应急救助装置automatic return 自动返回automatic telescopic center opening sliding door 自动中分式折叠滑动门automatic telescopic sliding door 自动折叠式滑动门20automobile lift 汽车电梯autowalk 自动人行道auxiliary apparatus 辅助装置auxiliary brake 辅助制动器auxiliary cicuit 辅助电路auxiliary contact 辅助触点auxiliary drive 辅助驱动auxiliary lock 辅助驱动auxiliary value 辅助材料auxiliary materials 辅助量auxiliary winding 辅助绕组available area 有效面积average 平均average car load 平均轿厢负载average dispatching interval 平均调度间隔时间21average interval 平均调度间隔时间average passenger waiting time 平均乘客侯梯时间average response time 平均应答时间average waiting quest 平均乘客量average waiting time 平均乘客侯梯时间axial flow fan 轴流式风扇axis 轴线axle 轴Bbabbit 巴氏合金babbit lined bearing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器22babbit metal 巴氏合金babbit rope socket 灌注式巴氏合金绳头back current 反向电流back e.m.f 反电动势back lash 轮齿隙back plunger type 后部柱塞式(液压梯) back side 后侧,后边back wall 后壁back type governor 轴流式限速器baked enamel 烤漆balance 平衡balance chain 平衡链balance coefficient 平衡系数balace weight 平衡器balanced traffic 平衡交通23ball bearing 滚珠轴承ball cup 球形碗ball pin 球形硝ball stop valve 球形断流器ball type bearing 滚珠轴承ballast 镇流器balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade panel 扶手板balustrade skirting 扶手群板balustrade lighting 扶手照明balustrades 扶手装置bandsaw 带锯bank 银行,群组,排bar 条,棒bar code 条形码bar lock 杆式锁24bare wire 裸线barricade 防护墙,隔墙barrier 隔板,栅栏base 基座,基础base plate 基板basement 地下室basement service 底下室服务basement type 底吊式basic logic element 基础逻辑元件basic logic function 基础逻辑功能batch production 批量生产battery 电池battery box 蓄电池箱battery charger 电池充电器battery- backed 电池支持的baud rate 波特率BCD(binary coded decimal) 二进制编码的十进制25beam 梁beam pad 井道电缆保护垫片beam pulley 抗绳轮bearing 轴承bearing bracket 轴承支架bearing cap 轴承盖bearing load 轴承负荷bearing plate 承重板bearing play 轴承间隙bearing sleeve 轴承衬套bearing stand 轴承座bed lift 病床电梯bed plate 底座bell 铃belt 胶带belt drive 胶带传动26belt grinder 胶带磨床belt pulley 胶带轮belt type moving walk 带式自动人行道bending 弯曲bending stress 弯曲应力benzine 轻汽油bevel gear 伞(斜)齿轮beveled washer 斜垫圈BGM (background music) 背景音乐BGM speaker 背景音乐扬声器bi-parting 对开式(上下开启) bi-parting door 垂直中分门bias 偏置,偏移bid 投标,报价bid table 报价单bidder 投标27bidding cycle 投标有效期限bidding procedure 投标(报价)程序bil of delivery 发货单bill of expenses 费用帐单bil of lading 海运提单bill of materials 材料单billing 开发票binary 二进制binder 装订册bipartite light transistor 双分式光电管bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关bitumen 沥青blade 叶片,刀片,锯片blade connector 刀形连接器28bleed-off circuit 泄放电路blind hoistway 盲(无门)井道block chart 方框图block diagram 方框图线路block of flats 住宅楼区blocking of control circuit 控制电路闭锁blower 鼓风机blower coil 吹弧线圈blower motor 风机电动机blue print 蓝图boarding 登梯boading floor 登梯楼层boarding landing 登梯层站boarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站29boading time 登梯时间boarding zone 登梯区域bobbing 绕线管boldface type 粗字体bolt 螺杆booster 升压机border condition 边界条件bore hole 钻孔,镗孔boring 镗boring lathe 镗床boring machine 镗床boring miller 镗铣床bottom 底部bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程bottom car runby 底部轿厢越程30bottom clearances for car 轿底间隙bottom counterweight clearance 轿底对重间隙bottom counterweight overtravel 轿底对重越程bottom counterweight runby 轿底对重越程bottom door retainer 门下角bottom floor 底部楼层bottom runby 底部越程bottom slow down switch 底部减速开关bottom stop 底部停战bottom terminal floor 底部楼层bottom terminal landing 底部端站bottom terminal stop 底端停站box 盒,箱box counterweight 箱式对重Braille 盲文字符31brake 制动器brake arm 制动器臂brake contact 制动器触点brake coutact 制动器联轴器brake dish 制动盘brake drum 制动轮brake energy 制动力brake level 制动器杠杆brake lever 制动器手柄brake lining 制动器衬套brake linkage 制动器连杆brake operater switch 制动操纵开关brake pin 制动器悄brake press 折弯机,压弯机brake pulley 制动轮brake release lever 制动器松闸手柄32brake release magnet 制动器送闸磁铁brake release time 制动器松闸时间brake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧brake tension 制动器紧力brake torque 制动器力矩brake wrench 制动器板手braking 制动braking distance 制动距离braking force 制动力branch circuit 分支电路brass founder 铸铜break 切断,破断break-down 故障breaking load 破断负荷33breaking strength 破断强度breaking test 破坏实验breather 通气管brick 砖brick-layer 砖砌工bridge circuit 桥式电路bridge connector 桥接器bridge jumper 桥接片bridge rectifier 桥式整流器bright controlling 光度控制broach 拉力broaching machine 拉床brochure 手册broken chain contact 断链触点broken circuit 断路broken drive chain contact 主驱动链保护装置34broken drive-chain safety device 驱动链条保护装置broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点broken step chain device 断绳开关broken step chain safety device 梯级链断列触点broken step safety device 梯级破列安全装置broken tape sweitch 短带开关bronze 铜brunching 成组,成群brush finished stainless steel 哑光不锈钢35brush holder 刷握,滑环brush yoke 刷架budget 预算buffer 缓冲器buffer stroke 缓冲器冲程buffer base 缓冲器底座buffer plate 缓冲器板buffer plunger 缓冲器柱塞buffer return spring 缓冲器复位弹簧buffer stand 缓冲器台buffer striking plate 缓冲器撞板buffer support 缓冲器支承buffer switch 缓冲器开关builder 建筑单位nbuilder's work 土建工程36buider's work drawing 土建图纸building 建筑building area 建筑面积building contractor 建筑承包商buiding facility 大楼设施building manager 大楼管理者building monitoring and security system 大楼监管和安全系统building population 大楼居住人口buiding supervision center 大楼监管中心built=in 装built-in escalator 组合式自动扶梯bumper 弹簧式缓冲器bumper rail 防撞板bumpy ride 颠簸振动的运行37buried 埋入的burn in (程序)灌入burr 毛刺,毛边burr free 去毛刺bus 总线bus bar 汇流条bush 衬套bushed bearing 加衬轴套bushing 衬套,轴套,套筒butt joint 平接,对焊button 按钮button switch 按钮开关buyer 买方buzzer 蜂鸣器buzzer switch 蜂鸣器开关bypass 直驶38by-pass button 直驶按钮by-pass valve 溢流阀bypassed floor 直驶不停楼层bypassed stop 直驶不停层站CC$F 到岸价cab 轿厢,座舱cab interior 轿厢部cabin 轿厢,座舱cabinet 柜,厢cable 电缆cable box 电缆箱cable car 缆车cable cleat 电缆夹具cable conductor 电缆导线cable entry 电缆引入39cable hanger 电缆吊架cable hole 电缆孔cable joint 电缆接头cable termination 电缆末端cable trunk 电缆接头CAD 计算机辅助设计cage 轿厢cage door 轿厢门calculation 计算机辅助设计calibrate 校准call 呼梯,呼叫call acceptance 呼梯接收call accepted 接受呼梯call accepted indicator 接受呼梯指示灯call accepted signal 接受呼梯信号call allocation 呼梯分派40cam tape control 偏心带控制cam-gear 凸轮传动装置cam-operated switch 凸轮(碰铁)操纵开关cancel 撤消,取消cancelingof call signal 呼梯信号消除cancellation 撤消,取消canopy 顶盖,大蓬canvas 帆布canvas hose 帆布软管cap 帽,盖子cap nut 螺母capacitance 电容,电容量capacitor 电容capacitor motor 电容器电机capacity 载重,容量,定员capacity plate 载量标牌41capstan 绞盘captive roller safety gear 滚柱式安全钳car 轿厢car annunciator 轿厢报警器car approaching gong 轿厢到站预报钟car apron 轿厢入口群板car assignment 轿厢调度,轿厢分配car automatic switch landing 轿厢开关自动停站car axis 轿厢中心线car back wall 轿厢后壁car botom clearance 轿厢安全高度car bottom overtravel 轿厢底部越层42call assignment 呼梯指令分配call band 呼梯信号带call button 呼梯按钮call cancel 呼梯取消call canceling 呼梯取消call coincidence 呼梯重合call contrl 呼梯指令控制call conmting system 呼梯计数系统call emitter 呼梯指令发送器call input 呼梯输入call input capacity 呼梯输入容call input device 呼梯输入装置call load 呼梯输入call memory 呼梯记忆call registered 登陆的呼梯call registered signal 登陆的呼梯信号call tegistration 呼梯登陆43call registration indicator 呼梯登陆信号call sequence 呼梯顺序call-back 召修call-back message 召修信息call-out response time 维修召唤应答时间call-out service 急修服务callinfg board 召唤盒calling floor 呼体楼层calling landing 呼梯CAM 计算机辅助制造cam 凸轮cam for positive operation 强制操纵凸轮cam lever 偏心柄cam shaft 偏心轴44car bottom runby 底部越程car buffer 轿厢缓冲器car button 轿厢按钮car cab 轿厢体car call 轿厢指令car call button 轿厢指令按钮car call cancel 轿召唤取消car call control 轿厢指令控制car call panel 轿厢(呼梯)指示盘car call stop 轿厢(呼梯)指令停车car cam 碰铁car canopy 轿厢顶盖car ceiling 轿厢装饰顶45car coming indicator 轿厢驶近指示灯car control lever 轿厢操纵手柄car control switch 轿厢操纵开关car counterweight 轿厢对重car cross-head 轿厢上梁car depth 轿厢深度car dispatch 轿厢调度car door 轿门car door catch 轿门栓car door closer 轿门关闭器car door electric contact 轿门电触点car door guide shoe 轿门导靴car door interlock 轿门联锁car door lock 轿门门锁car door rail 轿门导轨46car door sill 轿门地坎car door track 轿门导轨car elevator 汽车电梯car emergency exit 轿厢安全门,应急门car emergency opening 轿厢安全窗car emergency release switch 轿厢应急释放按钮car enclosure panel 轿厢壁板car enclosures 轿厢壁板car entrance 轿厢入口car extetior 轿厢外装修,轿厢外表car fan 轿厢风扇car floating movable platform 轿厢活动地板car floor frame 轿厢架,轿架car frame 轿厢架,轿架47car frame attachment 轿厢框架附件car frame plank 轿厢下梁car frame upright 轿厢立柱car front 轿厢前壁car full control 满载轿厢控制car gate 轿厢门car gate contact 轿门触点car gate electric contact 轿门电气触点car guide 轿厢导轨car guide axis 轿厢导轨中心线car handle control 手柄开关操纵,轿开关控制car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明48car isolation 轿厢隔震器car leveling device 轿厢平层装置car lift 汽车电梯car light 轿厢照明装置car light panel 轿厢照明板,照明天花板car lighting 轿厢照明car manual switch landing 轿厢手动开关停站car operation board 轿厢操纵盘car operation panel 操纵箱car overload 轿厢超载car panel 轿厢壁板car panel attachment 轿厢壁板附件car panel base 轿厢壁板底座49car panel with window 轿厢壁板上窗口cr parking device 轿厢驻停装置car platform 轿厢底,轿底car platform guard 轿厢站台护板car platform sill 轿厢car position indicator 轿厢指示灯,轿厢位置显示car position reference value 轿厢位置参考值car preference 轿厢优先权car push-button 轿厢按钮car rear wall 轿厢后壁car roof 轿厢顶,轿顶car safety 轿厢安全钳car safety bar for dumbwaiter 轿厢安全棒(杂货梯)50car safety gear 轿厢安全钳car safety mechanism switch 轿厢安全钳联动开关car sheave 轿厢绳轮car side emergency door 轿厢安全侧门car side opening 轿厢侧面开门car side wall 轿厢侧壁car sill 轿厢地坎car sling 轿厢架,吊架car station 轿厢操纵站car status information 轿厢运行状态信息car stop 轿厢停止car suspension 轿厢悬挂装置car switch 轿厢开关car switch automatic floor stop operation 轿厢开关自动停站装置51car switch control 轿厢开关控制car switch opration 手柄开关操纵,轿开关控制car top 轿厢顶部car top clearance 轿顶安全高度car top emergency exit 轿顶安全出口,轿顶应急出口car top guard 轿顶护栏car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站)car top light 轿顶照明装置car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆52car ventilation 轿厢通风car walls 轿厢壁,轿壁car weight 轿厢重量car width 轿厢宽度carbon 碳,石墨carbon brush 碳刷carbon contact 碳精触点carbon steel 碳素钢carburization 渗碳carburize 渗碳carburized hardening 渗碳硬化carburizer 渗碳剂card 卡片,纹板card reader 卡片读出器cardan joint 万向接头carpet 地毯carriage charges 运费53carry frequency 载波频率,开关工作频率carrying capacity 载运量,载运能力cart elevator 车辆运货电梯cartridge fuse 插塞式熔断器carving machine 刻模机cascade 级联,串联cascade sub-loop 串接式子回路case 箱,盒,外壳casing 保护套,外套casing of cylinder 油缸套cassette tape 录音带cast bronze 铸青铜cast iron 铸铁cast steel 铸钢casting 铸造castor oil 蓖麻油54catch 擎子,门扣,捕捉器catch block 安全钳catch clip 捕捉夹钳catch device 捕捉装置cathode 阴极cathode ray tube(CRT) 阴极射线管cavitation 气穴,涡穴,饱和压力点ceiling 吊顶ceiling assembling 轿顶cellulose 纤维板cement 水泥,胶合剂cement concrete 混凝土center 中心center latch 中心门栓center line 中心线center of curvature 曲率中心55center opening 中分式门center opening door 中分门center-opening folding door 中分式折叠门center opening two speed door 中分四扇门center opening vertical sliding door 中分式垂直滑动门center plunger hydraulic lift 柱塞直顶式液压电梯center support 中心支撑,中间支撑,第三支撑centigrade 摄氏温度central alarm 中央报警central control board 中央监控盘central control room 中央监控室central jack 中心液压装置56central position 中心位置centrifugal 离心的cenrifugal brake 离心制动器centrifugal cast 离心铸造centrifugal fan 离心式风扇centrifugal governor 离心式限速器centrifugal speed 离心速度centrifugal switch 离心开关centrifugal type governor 离心式限速器centripetal force 向心力ceramic capacitor 搪瓷电容certification 证书certifying body 认证机关chain 链条chain block 手拉葫芦chain bracket 链条托架57chain drive 链传动chain drive elevator 链驱动升降机chain drive machine 链驱动机chain gear 链轮chain guard 链防护罩chain link 链节,链环chain pitch 链条节距chain sag 链条下垂度chain sheave 链轮chain sprocket 链轮chain sustarned elevator 链支撑升降机chain tensioning device 链紧装置chain wheel 链轮chain wheel track 链轮导轨chamger 倒棱,去毛刺change switch 转换开关58change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性channel 槽钢channel iron 槽铁channel steel 槽钢character 特征,字符characteristic 特征,特性characteristic curve 特性曲线charge 充电,收费charged 带电,充电charging contactor 充电接触器charging set 充电chart 图表chart of accounts 成本图表check valve 止逆阀59chequer(checker)plate 网纹钢板chief engineer 总工程师chime 音钟chip 芯片chipboard 木屑板chisel 凿子choke 扼流,截流,阻塞choke coil 扼流线圈chopper 斩波器chrome 铬chuck 卡盘CIF(cost insurance and freight) 到岸价cinder concrete 煤渣混凝土circle 周期,圆circuit 电路circuit breaker 断电器,断路器60circuit diagram 电路图circular pitch 周节circulating pump 循环泵circulation 循环circumferential force 圆周力circumferential speed 圆周速度circumferential velocity 圆周速度CL(center line) 中心线clacking 盖板cladding 装饰clamp 夹clamp ring 压制环,加紧环clamping jaw 夹钳clamping sleeve 夹紧套桶clamping strap 制动带class of loading 灾荷种类clear depth 净深度61clear dimension 净尺寸clear door height 门净高度clear door width 门净宽度clear entrance to the car 轿厢入口净尺寸clear height 净高clear hoistway 井道净尺寸clear width 净宽度clerance 间隙clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度clearance top car 轿顶安全高度clearance top counterweight 对重装置顶部安全高度cleated riser 梯级竖板clevis U型夹client 客户,买主62clip 钳夹clockwise 顺时针的close circuit 闭合电路closed loop 闭环closed position (门)关闭位置closed position monitoring (门)关闭位置检测closed-loop control 闭环控制closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing travel 门关闭运行closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管63clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体) CNC(computerized numric control) 计算机数控coaxial cable 同轴电缆coast to stop 滑行停车coating 涂层cock 龙头code 码,符号,规程,规code of practice 实施规程,实用规程code word 代号文字coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数coefficient of friction 摩擦系数64coil 线圈,绕组coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate 栅栏门,折叠式门collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection 收集,集合collective control 集中控制collective full automatic operation 全自动集中控制collective operation elevator 集中操作电梯65collective selective 集选collective selective control 集选控制collector 集电路collision switch 碰撞开关color 颜色colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column 柱,立柱comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置68commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment 隔板,隔室compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compennsating device for hoist ropes 曳引绳补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置69compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensanting/equalizer disk 补偿/补偿器compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent 有资格的,胜任的70competent personnel 有资格的人员,胜任的人员competitor system 竞争机制component 部件compound wound 复绕compound wind motor 复励电动机comprehensive 综合的comprehensive maintenance contract 综合维修合同,全包维修合同comprehensive service contract 综合维修合同,全包维修合同compressing spring 压缩弹簧compression 压缩compressive stress 压应力compression switch 压缩开关compressor 压缩器71compulogic system 电脑程序控制系统computer 计算机computer peripheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed 隐蔽的,暗式concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容72condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod 连杆,连接杆73connection 连接connection diagram of controller 控制柜连线图connector 接线柱,连接器consecutively departing 依次派出的轿厢console panel 控制柜,控制盘constant 恒定的,常数constant HP motor 功率恒定型电机constant speed valve 比例控制阀,调速阀constant torque motor 力矩恒定型电机construction 安装,施工construction crane 建筑起重机construction layout drawing 土建图construction platform 安装平台,施工平台74construction site 安装工地,施工工地consultant 顾问,咨询机构consumption 消耗contact 触点contact angle 接触角contact brace 触头撑条contact burning 触头烧损contact carrier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger 接触指,滑触头contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷75contact mat 触头垫片contact normally closed 常闭触点contact normally open 常开触点contact pressure 触头压力contact resistance 接触电阻contactless 无触点contactless control 无触点控制contactless control system 无触点控制系统contactless switch 无触点开关contactor 接触器contents 容continuing travel indicator (轿)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关contract 合同,契约,承包合同76contract capacity 合同载重量,合同容量contract load 合同负载contract of indemnity 赔偿合同contract party 合同方,合同当事人conract specification 合同规定,合同明细表conract speed 合同速度,额定速度contract work system 合同制度control 控制control amplifier 调节放大器control bus 控制总线control cabinet 控制柜control cable 控制电缆control circuit 控制电路control device for handrail brekage 扶手带断带保护装置77control feature 控制特征control guard for handrail breakage 扶手带断带保护装置control gear 控制论control lever 控制杆control panel 控制屏control stand 控制台control station 控制站control switgh 控制开关control system 控制系统control system for elevator 电梯控制系统control technique 控制技术control type 控制形式control valve 控制阀control valve unit (液压)调节阀装置control voltage 控制电压,操作电压78controlled angle 控制角controller 控制柜controller base 控制柜底座controller cabinet 控制柜controller panel 控制屏controller wiring diagram 控制柜电路图controlling circuit 控制电路conventional 常规的conventional lift 普通电梯converter 整流器,转换头converter panel 换流器盘converter set 换流器组件converter unit 换流装置conveyance of passengers 乘客载运conveyer 输送机79conveyer track 输送车轨道cooler 冷却装置cooler air-conditioner 空调制冷cooling 冷却cooling device for semiconductor 半导体冷却装置cooling fan 冷却风扇COP(car operation panel) 轿厢操纵盘copper 铜cord 绳索,芯线cord drive 绳传动,(厅门) core 铁心core press 铁心压力core ventilation 铁心通风cork 软木cork packing 软木盘根corner 角,隔80corner post 对角立柱corpus lift 尸体升降机correct phase sequence 正确相序correcting 修正,校正correcting travel 校准运行correction 校正,校准corrective maintenance 校正维修corridor 走廊corrosion proof 防腐蚀的corrosion resistant 耐腐蚀的corrosion resistant coating 涂防锈漆层corrosive 腐蚀的cost 成本,费用cost accounting 成倍核算cost analysis 成本分析cost calculation 成倍计算cost comparison 成本比较81cost effective 价格划算的cost element 成本项目cost estimate 成本估算cost of material 材料成本cost of production 生产成本cost price 成本价cost share 成本份额cost situation 成本状况cost structure 成本结构cost-free 免费的cotter pin 开口销conter 计数器counter emf 反电动势counter inductor 记数感应器counter sunk head 埋头conuter-clockwise 逆时针方向counterbalance 相互平衡,配重平衡82countersink 沉头,埋入counterweight 对重装置,对重counterweight bottom runby 对重底部越程counterweight filler 对重块,对重装置重鉈counterweight filler weight 对重块,对重装置重鉈counterweight frame 对重框counterweight guard 对重防护栏counterweight header 对重头counterweight housing 对重架counterweight safety 对重安全钳counterweight sheave 对重绳轮counterweight sling 对重吊具countreweight suspension 对重悬挂装置83counterweight top clearance 对重装置顶部安全装置couple M to N 使M和N偶合coupled door panels 配对门扇counpler 联轴器coupling 联轴器coupling bolt 联轴器螺栓coupling sleeve 联接套筒cove 凹口cover 盖,保护层cover plate 盖板cover strip 覆盖条covered wire 覆层线CPS( central processing system) 中央处理系统CPU(central processing unit) 计算机中央处理器84crack 裂缝crack-resistant 抗裂的cracking pressure 破裂压力cradle beam 托架,横梁crank 曲轴crank operation 曲轴操作crank shaft 曲轴crank shaft oil seal 曲轴油封creep 爬行,蠕动creep speed 爬行速度,平层速度creeping-in distance 爬行距离Cremona's method 谷式应力图crest value 峰值crimp-meshed door 铁网门critical path planning 关键路线计划法85cross beam 顶梁,上梁cross head screwdriver 十字头螺丝功锥cross pin 十字销cross valve 三通阀cross-head 上梁cross-head screw 十字头螺钉cross-section 横截面crosshead sheave 轿顶轮crow bar 撬棒crown bar 顶杆crown wheel 盘形轮crushing 压碎,压溃cup 杯,盖子cup head square neck bolt 半圆头方颈螺栓current 电流current carrying 带电的86current carrying capacity 载流量current characteristic 电流参数current control loop 电流控制回路。
电梯专业英语[精彩]Guide rail (电梯)导轨Traction Machine (电梯) 曳引机 segment display (电梯)段码屏显示 Over Speed Governor (电梯)超速限速器 fish plate(电梯) 接合板, 鱼尾板 HAISUNG 韩国海星产电公司 (韩国最大的专业曳引机厂家之一),中国分厂TORIN美国通润公司,中国分厂 Intercom (电梯)对讲系统Selcom Door西尔康(公司名)门 DC motor直流电机(马达) Eshine易升(公司名)Anliso安利索(公司名)Door operator(电梯) 门机stainless steel sheet Hairline finish发纹处理不锈钢片Mirror Finish镜面抛光Mirror Etching镜面蚀刻,Elevator Car 电梯罐笼Light curtain光幕保护voice announcement语音报站 Encoder电梯编码器Position Indicator电梯轿厢位置 Emergency break system紧急逃生系统, Suspension road悬挂装置Diversion pulley导向滑轮Rope for elevator电梯钢丝绳 Micro Control微控制(公司名) yaskawa 安川Flat Cable扁形电梯电缆Landing door分层门MS painted, Hairline SS, Mirror SS(烤漆不锈钢,发纹不锈钢,镜面刨光不锈钢)Light curtain光幕保护voice announcement语音报站 Intercom 对讲系统Encoder 电梯编码器Position Indicator 电梯轿厢位置 Emergency break system, Suspension road 紧急逃生系统,悬挂装置电梯专业英语 abbreviation 缩语abnormal 不正常的,反常的abnormality monitoring 异常{BANNED}abrasion 磨损abrasion resistant 耐磨性abrasive cloth 砂布absorb 吸收absorber 减振器AC drive 交流拖动AC feedback control 交流反馈控制AC motor 交流电机AC servo 交流伺服AC servo motor 交流伺服电机AC single speed 交流单速AC two speed 交流双速AC two speed motor 交流双速电动机AC variale speed 交流调速AC(alternating current) 交流电acanning cycle 扫描周期,扫描循环acceleration control system 加速度控制系统acceleration(accel)rate 加速器accelerator 加速器acceptance of lift 电梯验收acceptance period 验收阶段acceptance test 验收试验acceptanec certificate 验收证书access door 检修门access forbidden 禁止入内access lift 通道电梯access security 通道防卫access switch 通道开关,维修用开关access way 进出通道accessibility 可通达性,接近的,难易程度accessible 允许进入accessible space 允许进入的场地accessory 配件,附件accident 事故accident insurance 事故保险accident prevention 事故预防accidental contact 触电accidental operation 误操作accordion door 折叠门accumulation 累积accumulator 蓄电池AC-GL machine 交流无齿曳引机acoustic 听觉的,声音的acrew die 板牙activate 启动,触发active mode 主动模式actual condition 实际状况,实际条件actual load 实际载荷actual state 实际状况actual value 实际值actuate 开动,操作,激励actuating linkege 操作连杆actuating magnet 操作磁铁actuation time 动作时间actuator 操纵机构,激励器,螺线管actuator bracket 调节器支架actuator plate 调节板ACVF drive 交流调频拖动ACVF system 交流调频系统ACVF(AC varible frequency) 交流调速ACVV dirve 交流调压拖动ACVV system 交流调压系统ACVV(AC varible voltage) 交流调压adaptation 适应,匹配adapter PCB 选通脉冲印刷电路板adapter(adapator) 适配器adapting 选配adaptive control system 自适应能力控制系统addendum 齿顶高,附录addendum circle 外圆adding working drawing 附加加工图addition 附加物,加法additional materials 附加材料address 地址adhesion 胶,粘合胶adhesion protective oil 防粘油adhesive foil 胶粘薄膜adhesive tape 胶带adjacent 邻近的adjacent car 相邻轿厢,相邻电梯adjacent entrance 相邻出入口adjusment 调试adjustable condensor 可变电容器adjustable resistance 可调电阻adjustable spanner 可调扳手adjustable speed electric drive 调速电力拖动adjustable wrench 活动扳手,可调扳手adjusting screw 调节螺丝adjustor 调试员administation overjhead rate 管理费用标准administration cost 管理成本administration expenses 管理费用advance door opening 提前开门advance payment 预付款advanced 提前的,先进的advanced carriage 超前拖板(选层器)advancing position reference value 超前位置参考值aerial cableway 空中缆车,架空索道aerial ropeway 空中缆车,架空索道aerial tramway 空中缆车,架空索道aesthetic 美观after sales service 售后服务agency 代理agenda 议程air cord (门机用)航空钢丝绳air purifier 空气滤清剂air ventilator 通风管air-bleed 空气分泄器airborne noise 空气传播噪声air-condition 空调air-gap 气隙alarm 警报alarm bell 警铃alarm button 警铃按钮alarm buzzer 警报蜂鸣器alarm circuit 警报电路alarm system 警报系统ALC(autoclaved light-weight concrete) 蒸压轻质混凝土alcove arrangement 电梯U型排列法algorithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignment gauge 校正量规alkali 碱all-computer-controlled 计算机全控的allocation 分配,分派allocation of landing call 层站呼梯指令分配allowance 允用误差,加工余量allowble stress for temporary load 允许暂时应力值alloy 合金alloy steel 合金钢alteration 改进alternate floor 隔层alumina 氧化铝aluminum 铝aluminum alloy 铝合金aluminum bronze 铝青铜aluminum cladding 铝制包层alumite 防蚀铝alundum 氧化铝ambient 环境的ambient noise 环境噪音ambient temperature 环境温度ammeter 安培计ammonia 氨amperage 电流强度ampere 安培amplification 放大amplification stage 放大等级amplifier 放大器amplifying tube 放大管amplitude 幅度analog adder 模拟加法器analog computer 模拟计算机analog speed card 模拟曲线板analog-digital converter 模拟-数字转换器analogue(analog) 模拟analysis 分析analysis mode 分析模拟anchor bolt 地脚螺栓anchorage 锚具,锚定angle bar 角钢angle guide 角铁导轨angle iron 角铁angle iron frame 角铁框架angle of contact 接触角angle of deflection 导向角angle of inclination 倾斜角angle of lead 导程角angle of traction 曳引机包角angle of wrap 包角angle steel 角钢angular contact ball bearing 向心推力球轴承angular contact bearing 角面接触滚动轴承angular gear 斜齿轮angular retardationg 角减速度angular velocity 角速度anneal 退火annealing 退火annual inspection 年检annual report 年度报告annunciator 报音器,声音合成器anode 阳极anodize 氧极氧化ANSI(America Nationa Standard Instirute) 美国国家标准协会anti-clockwise 逆时钟方向anti-corrosive paint 防腐蚀漆anti-creep 防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰anti-nuisance device 防捣乱装置anti-phase braking 反向制动anti-phase current 反相电流anti-rebound of compensation rope device 补偿绳防跳装置anti-residual 防剩磁anti-resonance 抗谐振anti-reversion device 防反转装置anti-rust 防锈anti-stall 防空转anti-vibralion pad 防震垫APM(automatic people mover) 自动人员运输机apparen power 视在功率apparent output 视在输出applicant 申请人application 申请application guide 应用指南aprons 裙板arbour 轴,杆arc chamber 电弧隔离室arc protection 防电弧arc quenching 熄焊弧arc shield 电弧屏蔽arc suppressor 灭焊器architect 设计单位architecture 建筑学architrave 门框area 面积arm 臂,支路armature 电驱armature coil 电驱线圈armature current 电驱电流armature lamination 电驱铁芯片armature shaft 电驱轴armature spider 星形轮armature winding 电驱绕组armoured 蛇皮管的armoured cable 蛇皮管电缆armoured conduit 导线管arrangement 布置arrival bell 到站铃arrival buzer 到站蜂鸣器arrival floor 到达楼层arrival gong 到站钟arrival rate 到站率article of consumption 消耗品artificial intelligence 人工智能artistic 工艺artistic face 工艺表面asbestos packing 石棉盘根ascending 上升ASIC(application specific integrated circuit) 专用集成电路assemble 装配assembler language 汇编语言assembly of hinge 铰链组装assign 分配astragal 装饰镶条atmospheric influence 大气影响attachment 附件attendant control 有司机控制attendant control compartment 有司机控制盒attendant operation 有司机操作audible signal 音响信号audio tape recording 磁带录音authority 当局,核准部门authority of lift acceptance 电梯验收部门authorized 授权的,核准的authorized user 核准使用者auto-adaptation 自适用AutoCAD 自动计算机辅助设计autographic recoder 自动记录仪automatic 自动的automatic allocator 自动分派器automatic by-pass 自动直驶automatic center opening sliding door 自动中分式滑动门automatic closer 自动关闭门automatic dispatch 自动调度automatic door 自动门automatic homing 自动回基层automatic landing 自动停站automatic landing system by spare battery 靠备用蓄电池的自动停站设备automatic leveling 自动平层automatic lubricator 自动润滑装置automatic parking garage 自动停车库automatic parking system 自动停车系统automatic relevelling 自动平层校正automatic rescue device 应急救助装置automatic return 自动返回automatic telescopic center opening sliding door 自动中分式折叠滑动门automatic telescopic sliding door 自动折叠式滑动门automobile lift 汽车电梯autowalk 自动人行道auxiliary apparatus 辅助装置auxiliary brake 辅助制动器auxiliary cicuit 辅助电路auxiliary contact 辅助触点auxiliary drive 辅助驱动auxiliary lock 辅助锁auxiliary materials 辅助量auxiliary value 辅助材料auxiliary winding 辅助绕组available area 有效面积average 平均average car load 平均轿厢负载average dispatching interval 平均调度间隔时间average interval 平均调度间隔时间average passenger waiting time 平均乘客侯梯时间average response time 平均应答时间average waiting quest 平均乘客量average waiting time 平均乘客侯梯时间axial flow fan 轴流式风扇axis 轴线axle 轴babbit 巴氏合金babbit lined bearing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器babbit metal 巴氏合金babbit rope socket 灌注式巴氏合金绳头back current 反向电流back e.m.f 反电动势back lash 轮齿隙back plunger type 后部柱塞式(液压梯) back side 后侧,后边back type governor 轴流式限速器back wall 后壁baked enamel 烤漆balace weight 平衡器balance 平衡balance chain 平衡链balance coefficient 平衡系数balanced traffic 平衡交通ball bearing 滚珠轴承ball cup 球形碗ball pin 球形硝ball stop valve 球形断流器ball type bearing 滚珠轴承ballast 镇流器balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade lighting 扶手照明balustrade panel 扶手板balustrade skirting 扶手群板balustrades 扶手装置bandsaw 带锯bank 银行,群组,排bar 条,棒bar code 条形码bar lock 杆式锁bare wire 裸线barricade 防护墙,隔墙barrier 隔板,栅栏base 基座,基础base plate 基板basement 地下室basement service 底下室服务basement type 底吊式basic logic element 基础逻辑元件basic logic function 基础逻辑功能batch production 批量生产battery 电池battery- backed 电池支持的battery box 蓄电池箱battery charger 电池充电器baud rate 波特率BCD(binary coded decimal) 二进制编码的十进制beam 梁beam pad 井道内电缆保护垫片beam pulley 抗绳轮bearing 轴承bearing bracket 轴承支架bearing cap 轴承盖bearing load 轴承负荷bearing plate 承重板bearing play 轴承间隙bearing sleeve 轴承衬套bearing stand 轴承座bed lift 病床电梯bed plate 底座bell 铃belt 胶带belt drive 胶带传动belt grinder 胶带磨床belt pulley 胶带轮belt type moving walk 带式自动人行道bending 弯曲bending stress 弯曲应力benzine 轻汽油bevel gear 伞(斜)齿轮beveled washer 斜垫圈BGM (background music) 背景音乐BGM speaker 背景音乐扬声器bias 偏置,偏移bid 投标,报价bid table 报价单bidder 投标bidding cycle 投标有效期限bidding procedure 投标(报价)程序bil of delivery 发货单bil of lading 海运提单bill of expenses 费用帐单bill of materials 材料单billing 开发票binary 二进制binder 装订册bi-parting 对开式(上下开启)bi-parting door 垂直中分门bipartite light transistor 双分式光电管bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关bitumen 沥青blade 叶片,刀片,锯片blade connector 刀形连接器bleed-off circuit 泄放电路blind hoistway 盲(无门)井道block chart 方框图block diagram 方框图线路block of flats 住宅楼区blocking of control circuit 控制电路闭锁blower 鼓风机blower coil 吹弧线圈blower motor 风机电动机blue print 蓝图boading floor 登梯楼层boading time 登梯时间boarding 登梯boarding landing 登梯层站boarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站boarding zone 登梯区域bobbing 绕线管boldface type 粗字体bolt 螺杆booster 升压机border condition 边界条件bore hole 钻孔,镗孔boring 镗boring lathe 镗床boring machine 镗床boring miller 镗铣床bottom 底部bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程bottom car runby 底部轿厢越程bottom clearances for car 轿底间隙bottom counterweight clearance 轿底对重间隙bottom counterweight overtravel 轿底对重越程bottom counterweight runby 轿底对重越程bottom door retainer 门下角bottom floor 底部楼层bottom runby 底部越程bottom slow down switch 底部减速开关bottom stop 底部停战bottom terminal floor 底部楼层bottom terminal landing 底部端站bottom terminal stop 底端停站box 盒,箱box counterweight 箱式对重Braille 盲文字符brake 制动器brake arm 制动器臂brake contact 制动器触点brake coutact 制动器联轴器brake dish 制动盘brake drum 制动轮brake energy 制动力brake level 制动器杠杆brake lever 制动器手柄brake lining 制动器衬套brake linkage 制动器连杆brake operater switch 制动操纵开关brake pin 制动器悄brake press 折弯机,压弯机brake pulley 制动轮brake release lever 制动器松闸手柄brake release magnet 制动器送闸磁铁brake release time 制动器松闸时间brake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧brake tension 制动器张紧力brake torque 制动器力矩brake wrench 制动器板手braking 制动braking distance 制动距离braking force 制动力branch circuit 分支电路brass founder 铸铜break 切断,破断break-down 故障breaking load 破断负荷breaking strength 破断强度breaking test 破坏实验breather 通气管brick 砖brick-layer 砖砌工bridge circuit 桥式电路bridge connector 桥接器bridge jumper 桥接片bridge rectifier 桥式整流器bright controlling 光度控制broach 拉力broaching machine 拉床brochure 手册broken chain contact 断链触点broken circuit 断路broken drive chain contact 主驱动链保护装置broken drive-chain safety device 驱动链条保护装置broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点broken step chain device 断绳开关broken step chain safety device 梯级链断列触点broken step safety device 梯级破列安全装置broken tape sweitch 短带开关bronze 铜brunching 成组,成群brush finished stainless steel 哑光不锈钢brush holder 刷握,滑环brush yoke 刷架budget 预算buffer 缓冲器buffer base 缓冲器底座buffer plate 缓冲器板buffer plunger 缓冲器柱塞buffer return spring 缓冲器复位弹簧buffer stand 缓冲器台buffer striking plate 缓冲器撞板buffer stroke 缓冲器冲程buffer support 缓冲器支承buffer switch 缓冲器开关buider's work drawing 土建图纸buiding facility 大楼设施buiding supervision center 大楼监管中心builder 建筑单位building 建筑building area 建筑面积building contractor 建筑承包商building manager 大楼管理者building monitoring and security system 大楼监管和安全系统building population 大楼居住人口built=in 内装built-in escalator 组合式自动扶梯bumper 弹簧式缓冲器bumper rail 防撞板bumpy ride 颠簸振动的运行buried 埋入的burn in (程序)灌入burr 毛刺,毛边burr free 去毛刺bus 总线bus bar 汇流条bush 衬套bushed bearing 加衬轴套bushing 衬套,轴套,套筒butt joint 平接,对焊button 按钮button switch 按钮开关buyer 买方buzzer 蜂鸣器buzzer switch 蜂鸣器开关bypass 直驶by-pass button 直驶按钮by-pass valve 溢流阀bypassed floor 直驶不停楼层bypassed stop 直驶不停层站C$F 到岸价cab 轿厢,座舱cab interior 轿厢内部cabin 轿厢,座舱cabinet 柜,厢cable 电缆cable box 电缆箱cable car 缆车cable cleat 电缆夹具cable conductor 电缆导线cable entry 电缆引入cable hanger 电缆吊架cable hole 电缆孔cable joint 电缆接头cable termination 电缆末端cable trunk 电缆接头CAD 计算机辅助设计cage 轿厢cage door 轿厢门calculation 计算机辅助设计calibrate 校准call 呼梯,呼叫call acceptance 呼梯接收call accepted 接受呼梯call accepted indicator 接受呼梯指示灯call accepted signal 接受呼梯信号call allocation 呼梯分派call assignment 呼梯指令分配call band 呼梯信号带call button 呼梯按钮call cancel 呼梯取消call canceling 呼梯取消call coincidence 呼梯重合call conmting system 呼梯计数系统call contrl 呼梯指令控制call emitter 呼梯指令发送器call input 呼梯输入call input capacity 呼梯输入内容call input device 呼梯输入装置call load 呼梯输入call memory 呼梯记忆call registered 登陆的呼梯call registered signal 登陆的呼梯信号call registration indicator 呼梯登陆信号call sequence 呼梯顺序call tegistration 呼梯登陆call-back 召修call-back message 召修信息callinfg board 召唤盒calling floor 呼体楼层calling landing 呼梯call-out response time 维修召唤应答时间call-out service 急修服务CAM 计算机辅助制造cam 凸轮cam for positive operation 强制操纵凸轮cam lever 偏心柄cam shaft 偏心轴cam tape control 偏心带控制cam-gear 凸轮传动装置cam-operated switch 凸轮(碰铁)操纵开关cancel 撤消,取消cancelingof call signal 呼梯信号消除cancellation 撤消,取消canopy 顶盖,大蓬canvas 帆布canvas hose 帆布软管cap 帽,盖子cap nut 螺母capacitance 电容,电容量capacitor 电容capacitor motor 电容器电机capacity 载重,容量,定员capacity plate 载量标牌capstan 绞盘captive roller safety gear 滚柱式安全钳car 轿厢car annunciator 轿厢报警器car approaching gong 轿厢到站预报钟car apron 轿厢入口群板car assignment 轿厢调度,轿厢分配car automatic switch landing 轿厢开关自动停站car axis 轿厢中心线car back wall 轿厢后壁car botom clearance 轿厢安全高度car bottom overtravel 轿厢底部越层car bottom runby 底部越程car buffer 轿厢缓冲器car button 轿厢按钮car cab 轿厢体car call 轿厢指令car call button 轿厢指令按钮car call cancel 轿内召唤取消car call control 轿厢指令控制car call panel 轿厢(呼梯)指示盘car call stop 轿厢(呼梯)指令停车car cam 碰铁car canopy 轿厢顶盖car ceiling 轿厢装饰顶car coming indicator 轿厢驶近指示灯car control lever 轿厢操纵手柄car control switch 轿厢操纵开关car counterweight 轿厢对重car cross-head 轿厢上梁car depth 轿厢深度car dispatch 轿厢调度car door 轿门car door catch 轿门栓car door closer 轿门关闭器car door electric contact 轿门电触点car door guide shoe 轿门导靴car door interlock 轿门联锁car door lock 轿门门锁car door rail 轿门导轨car door sill 轿门地坎car door track 轿门导轨car elevator 汽车电梯car emergency exit 轿厢安全门,应急门car emergency opening 轿厢安全窗car emergency release switch 轿厢应急释放按钮car enclosure panel 轿厢壁板car enclosures 轿厢壁板car entrance 轿厢入口car extetior 轿厢外装修,轿厢外表car fan 轿厢风扇car floating movable platform 轿厢活动地板car floor frame 轿厢架,轿架car frame 轿厢架,轿架car frame attachment 轿厢框架附件car frame plank 轿厢下梁car frame upright 轿厢立柱car front 轿厢前壁car full control 满载轿厢控制car gate 轿厢门car gate contact 轿门触点car gate electric contact 轿门电气触点car guide 轿厢导轨car guide axis 轿厢导轨中心线car handle control 手柄开关操纵,轿内开关控制car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明car isolation 轿厢隔震器car leveling device 轿厢平层装置car lift 汽车电梯car light 轿厢照明装置car light panel 轿厢照明板,照明天花板car lighting 轿厢照明car manual switch landing 轿厢手动开关停站car operation board 轿厢操纵盘car operation panel 操纵箱car overload 轿厢超载car panel 轿厢壁板car panel attachment 轿厢壁板附件car panel base 轿厢壁板底座car panel with window 轿厢壁板上窗口car platform 轿厢底,轿底car platform guard 轿厢站台护板car platform sill 轿厢car position indicator 轿厢指示灯,轿厢位置显示car position reference value 轿厢位置参考值car preference 轿厢优先权car push-button 轿厢按钮car rear wall 轿厢后壁car roof 轿厢顶,轿顶car safety 轿厢安全钳car safety bar for dumbwaiter 轿厢安全棒(杂货梯) car safety gear 轿厢安全钳car safety mechanism switch 轿厢安全钳联动开关car sheave 轿厢绳轮car side emergency door 轿厢安全侧门car side opening 轿厢侧面开门car side wall 轿厢侧壁car sill 轿厢地坎car sling 轿厢架,吊架car station 轿厢操纵站car status information 轿厢运行状态信息car stop 轿厢停止car suspension 轿厢悬挂装置car switch 轿厢开关car switch automatic floor stop operation 轿厢开关自动停站装置car switch control 轿厢开关控制car switch opration 手柄开关操纵,轿内开关控制car top 轿厢顶部car top clearance 轿顶安全高度car top emergency exit 轿顶安全出口,轿顶应急出口car top guard 轿顶护栏car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站)car top light 轿顶照明装置car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆car ventilation 轿厢通风car walls 轿厢壁,轿壁car weight 轿厢重量car width 轿厢宽度carbon 碳,石墨carbon brush 碳刷carbon contact 碳精触点carbon steel 碳素钢carburization 渗碳carburize 渗碳carburized hardening 渗碳硬化carburizer 渗碳剂card 卡片,纹板card reader 卡片读出器cardan joint 万向接头carpet 地毯carriage charges 运费carry frequency 载波频率,开关工作频率carrying capacity 载运量,载运能力cart elevator 车辆运货电梯cartridge fuse 插塞式熔断器carving machine 刻模机cascade 级联,串联cascade sub-loop 串接式子回路case 箱,盒,外壳casing 保护套,外套casing of cylinder 油缸套cassette tape 录音带cast bronze 铸青铜cast iron 铸铁cast steel 铸钢casting 铸造castor oil 蓖麻油catch 擎子,门扣,捕捉器catch block 安全钳catch clip 捕捉夹钳catch device 捕捉装置cathode 阴极cathode ray tube(CRT) 阴极射线管cavitation 气穴,涡穴,饱和压力点ceiling 吊顶ceiling assembling 轿顶cellulose 纤维板cement 水泥,胶合剂cement concrete 混凝土cenrifugal brake 离心制动器center 中心center latch 中心门栓center line 中心线center of curvature 曲率中心center opening 中分式门center opening door 中分门center opening two speed door 中分四扇门center opening vertical sliding door 中分式垂直滑动门center plunger hydraulic lift 柱塞直顶式液压电梯center support 中心支撑,中间支撑,第三支撑center-opening folding door 中分式折叠门centigrade 摄氏温度central alarm 中央报警central control board 中央监控盘central control room 中央监控室central jack 中心液压装置central position 中心位置centrifugal 离心的centrifugal cast 离心铸造centrifugal fan 离心式风扇centrifugal governor 离心式限速器centrifugal speed 离心速度centrifugal switch 离心开关centrifugal type governor 离心式限速器centripetal force 向心力ceramic capacitor 搪瓷电容certification 证书certifying body 认证机关chain 链条chain block 手拉葫芦chain bracket 链条托架chain drive 链传动chain drive elevator 链驱动升降机chain drive machine 链驱动机chain gear 链轮chain guard 链防护罩chain link 链节,链环chain pitch 链条节距chain sag 链条下垂度chain sheave 链轮chain sprocket 链轮chain sustarned elevator 链支撑升降机chain tensioning device 链张紧装置chain wheel 链轮chain wheel track 链轮导轨chamger 倒棱,去毛刺change switch 转换开关change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性channel 槽钢channel iron 槽铁channel steel 槽钢character 特征,字符characteristic 特征,特性characteristic curve 特性曲线charge 充电,收费charged 带电,充电charging contactor 充电接触器charging set 充电chart 图表chart of accounts 成本图表check valve 止逆阀chequer(checker)plate 网纹钢板chief engineer 总工程师chime 音钟chip 芯片chipboard 木屑板chisel 凿子choke 扼流,截流,阻塞choke coil 扼流线圈chopper 斩波器chrome 铬chuck 卡盘CIF(cost insurance and freight) 到岸价cinder concrete 煤渣混凝土circle 周期,圆circuit 电路circuit breaker 断电器,断路器circuit diagram 电路图circular pitch 周节circulating pump 循环泵circulation 循环circumferential force 圆周力circumferential speed 圆周速度circumferential velocity 圆周速度CL(center line) 中心线clacking 盖板cladding 装饰clamp 夹clamp ring 压制环,加紧环clamping jaw 夹钳clamping sleeve 夹紧套桶clamping strap 制动带class of loading 灾荷种类clear depth 净深度clear dimension 净尺寸clear door height 门净高度clear door width 门净宽度clear entrance to the car 轿厢入口净尺寸clear height 净高clear hoistway 井道净尺寸clear width 净宽度clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度clearance top car 轿顶安全高度clearance top counterweight 对重装置顶部安全高度cleated riser 梯级竖板clerance 间隙clevis U型夹client 客户,买主clip 钳夹clockwise 顺时针的close circuit 闭合电路closed loop 闭环closed position (门)关闭位置closed position monitoring (门)关闭位置检测closed-loop control 闭环控制closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing travel 门关闭运行closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体)CNC(computerized numric control) 计算机数控coast to stop 滑行停车coating 涂层coaxial cable 同轴电缆cock 龙头code 码,符号,规程,规范code of practice 实施规程,实用规程code word 代号文字coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数coefficient of friction 摩擦系数coil 线圈,绕组coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate 栅栏门,折叠式门collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection 收集,集合collective control 集中控制collective full automatic operation 全自动集中控制collective operation elevator 集中操作电梯collective selective 集选collective selective control 集选控制collector 集电路collision switch 碰撞开关color 颜色colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column 柱,立柱comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment 隔板,隔室compennsating device for hoist ropes 曳引绳补偿装置compensanting/equalizer disk 补偿/补偿器compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent 有资格的,胜任的competent personnel 有资格的人员,胜任的人员competitor system 竞争机制component 部件compound wind motor 复励电动机compound wound 复绕comprehensive 综合的comprehensive maintenance contract 综合维修合同,全包维修合同comprehensive service contract 综合维修合同,全包维修合同compressing spring 压缩弹簧compression 压缩compression switch 压缩开关compressive stress 压应力compressor 压缩器compulogic system 电脑程序控制系统computer 计算机computer peripheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed 隐蔽的,暗式concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod 连杆,连接杆connection 连接connection diagram of controller 控制柜连线图connector 接线柱,连接器conract specification 合同规定,合同明细表conract speed 合同速度,额定速度consecutively departing 依次派出的轿厢console panel 控制柜,控制盘constant 恒定的,常数constant HP motor 功率恒定型电机constant speed valve 比例控制阀,调速阀constant torque motor 力矩恒定型电机construction 安装,施工construction crane 建筑起重机construction layout drawing 土建图construction platform 安装平台,施工平台construction site 安装工地,施工工地consultant 顾问,咨询机构consumption 消耗contact 触点contact angle 接触角contact brace 触头撑条contact burning 触头烧损contact carrier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger 接触指,滑触头contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷contact mat 触头垫片contact normally closed 常闭触点contact normally open 常开触点contact pressure 触头压力contact resistance 接触电阻contactless 无触点contactless control 无触点控制contactless control system 无触点控制系统contactless switch 无触点开关contactor 接触器contents 内容conter 计数器continuing travel indicator (轿内)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关contract 合同,契约,承包合同contract capacity 合同载重量,合同容量contract load 合同负载contract of indemnity 赔偿合同contract party 合同方,合同当事人contract work system 合同制度control 控制control amplifier 调节放大器control bus 控制总线control cabinet 控制柜control cable 控制电缆control circuit 控制电路control device for handrail brekage 扶手带断带保护装置control feature 控制特征control gear 控制论control guard for handrail breakage 扶手带断带保护装置control lever 控制杆control panel 控制屏control stand 控制台control station 控制站control switgh 控制开关control system 控制系统control system for elevator 电梯控制系统control technique 控制技术control type 控制形式control valve 控制阀control valve unit (液压)调节阀装置control voltage 控制电压,操作电压controlled angle 控制角controller 控制柜controller base 控制柜底座controller cabinet 控制柜controller panel 控制屏controller wiring diagram 控制柜电路图controlling circuit 控制电路conuter-clockwise 逆时针方向conventional 常规的conventional lift 普通电梯converter 整流器,转换头converter panel 换流器盘converter set 换流器组件converter unit 换流装置conveyance of passengers 乘客载运conveyer 输送机conveyer track 输送车轨道cooler 冷却装置cooler air-conditioner 空调制冷cooling 冷却cooling device for semiconductor 半导体冷却装置cooling fan 冷却风扇COP(car operation panel) 轿厢操纵盘copper 铜cord 绳索,芯线cord drive 绳传动,(厅门)core 铁心core press 铁心压力core ventilation 铁心通风cork 软木cork packing 软木盘根corner 角,隔corner post 对角立柱corpus lift 尸体升降机correct phase sequence 正确相序correcting 修正,校正correcting travel 校准运行correction 校正,校准corrective maintenance 校正维修corridor 走廊corrosion proof 防腐蚀的corrosion resistant 耐腐蚀的corrosion resistant coating 涂防锈漆层corrosive 腐蚀的cost 成本,费用cost accounting 成倍核算cost analysis 成本分析cost calculation 成倍计算cost comparison 成本比较cost effective 价格划算的cost element 成本项目cost estimate 成本估算。
Guide rail 10mm (T75-3/B) with fish plate & screwT75-3/B型带有螺纹接合板的10毫米导轨Guide rail 15.88mm (T89/B) with fish plate & screwT89/B型带有螺纹接合板的15.88毫米导轨Guide rail 5mm (T50/A) with fish plate & screwT50/A型带有螺纹接合板的5毫米导轨Hollow guide rail (TH3, TH3A, TH5, TH5A) with fish plate & screwTH3, TH3A, TH5和TH5A型带有螺纹接合板的中空导轨Traction Machine TORIN SF 140 1MS 500 KG 5.5 KW通润SF140型曳引机1MS 载重量500 公斤; 功率5.5 千瓦Traction Machine TORIN FYJ 180, 1MS 630 KG通润FYJ 180型曳引机, 1MS载重量630 公斤Traction Machine HAISUNG (GT) China HSU 130,海星(GT) 曳引机(中国制造)HSU 130,Traction Machine HAISUNG China HSU 150G, 60m/min 750 KG & 900 KG海星(HSU)曳引机(中国制造)150G, 运行速度60米/分钟, 载重量750公斤-900公斤Other China Traction Machine 480 Kg to 900 Kg其他中国制造的曳引机:载重量480千克-- 900千克COP with 7 segment display & Intercom 6 stop, 7 stop….10 stop带有7段段码屏显示和6 层,7层…10层对讲系统的COPHOP with 7 segment display带有7段段码屏显示的HOP7 segment display7段段码屏显示Complete Inspection Box全面检查箱Over Speed Governor 1ms超速限速器1msSelcom Door operator with accessories 700mm & 800mm Without VVVF (AC2) speed with DC motor带有700毫米和800毫米无极调速器(AC2)的直流电机配置的西尔康门机Selcom Landing Header with accessories 700mm & 800mm配置700mm &和800mm???的西尔康层门头Genesis, Eshine or Anliso Door operator with accessories 700mm & 800mm VVVF & Without VVVF (AC2)配置700毫米和800毫米无极或单极调速器(AC2)的Genesis, 易升或安利索门机Genesis, Eshine or Anliso Landing Header with accessories 700mm & 800mm带有700mm & 800mm 配件的Genesis(公司名,懒得查了!)、易升或安利索层门头Standered 700mm & 800mm MS painted, Hairline SS, Mirror SS, Landing door标准700mm和800mm的烤漆不锈钢、发纹不锈钢和镜面刨光不锈钢分层门Flat Cable 12 core, 24 core, 36 core, 40 core, 48 core扁形电梯电缆:12 芯, 24芯, 36芯, 40芯, 48芯Yaskawa, Delta, and other Inverter with PG card and breaking resistance & filter, 5.5, 7.5, 10 KW安川变频器, 德尔塔变频器和其他带有PG卡的反应换流器,断接电阻和滤波器的功率:5.5, 7.5和10千瓦Complete control system (Mico Control, Wuxi Zhongxiu, Step or other reputed Manufacturer)全面控制系统(微控制公司, 无锡Zhongxiu(是否是中国?写错了?有名的制造商)Mother Board for control控制母板:Rope for elevator 8mm, 10mm, 12mm电梯钢丝绳:8mm, 10mm, 12mmDiversion pulley 400mm (you find this from Traction Machine Manufacturer)导向滑轮:400毫米(你可以找到该型号的曳引机制造商)Stainless Steel Sheet Hairline finish, Mirror Finish & Mirror Etching, 0.7mm, 0.8mm,1.0mm发纹处理、镜面抛光以及镜面蚀刻不锈钢片:0.7毫米,0.8毫米和1.0毫米Mirror Etching and hairline finish Elevator Car 1050 x 1100 mm镜面蚀刻和发纹处理的电梯罐笼1050毫米x 1100毫米Light curtain光幕保护voice announcement语音报站Intercom对讲系统Encoder电梯编码器Position Indicator电梯轿厢位置Emergency break system, Suspension road紧急逃生系统,悬挂装置Guide rail (电梯)导轨Traction Machine (电梯) 曳引机segment display (电梯)段码屏显示Over Speed Governor (电梯)超速限速器fish plate(电梯) 接合板, 鱼尾板HAISUNG韩国海星产电公司(韩国最大的专业曳引机厂家之一),中国分厂TORIN美国通润公司,中国分厂Intercom (电梯)对讲系统Selcom Door西尔康(公司名)门DC motor直流电机(马达)Eshine易升(公司名)Anliso安利索(公司名)Door operator(电梯) 门机stainless steel sheet Hairline finish发纹处理不锈钢片Mirror Finish镜面抛光Mirror Etching镜面蚀刻,Elevator Car 电梯罐笼Light curtain光幕保护voice announcement语音报站Encoder电梯编码器Position Indicator电梯轿厢位置Emergency break system紧急逃生系统, Suspension road悬挂装置Diversion pulley导向滑轮Rope for elevator电梯钢丝绳Micro Control微控制(公司名)yaskawa 安川Flat Cable扁形电梯电缆Landing door分层门MS painted, Hairline SS, Mirror SS(烤漆不锈钢,发纹不锈钢,镜面刨光不锈钢)gate 轿门,闸门电路,选通器gate action 选通作用gate amplifier 选通脉冲放大器gate bias 栅偏压gate closer 关门器gate contact 门触点gate controller 门控器gate diode 门电路二极管gate generator 门脉冲发生器gate guide shoe 门导靴gate lock 门锁gate operator 开关门机gate power operator 自动开关门机gate pulse 门脉冲gate sill 门地坎gate switch 门开关gate time 选通时间gate trigger 控制门触发器gate turnoff thyristor 可控硅开关gate vale 闸阀gauge 量规,量具gear 齿轮gear box 齿轮箱gear driving machine 有齿轮曳引机gear efficiency 机器效率,齿轮效率gear grease 齿轮黄油gear hobbing 滚齿gear parts 齿轮部分gear pump 齿轮泵gear ratio 传动比gear reducer 齿轮减速装置gear ring 齿轮圈gear speed reducer 齿轮减速装置gear teeth 轮齿geared elevator 有齿轮电梯geared hoising machine 有齿轮曳引机geared lift 有齿轮电梯geared machine 有齿轮曳引机geared motor 齿轮传动电动机gearless 无齿轮gearless driving machine 无齿轮曳引机gearless elevator 无齿轮电梯gearless hoisting machine 无齿轮曳引机gearless machine 无齿轮曳引机general contractor 总承包商general drawing 总图general sales overheads 一般销售开支generate 发电generator 发电机generator field control 发电机磁场控制generator self-excited field 发电机自激场generator set 发电机组germanium 锗germanium diode 锗二极管gib 镶条,衬垫,楔块gland 压盖,密封套glass 玻璃glass balustrade 玻璃扶栏glass elevator 观光电梯glass mounting bracket 玻璃支架glass panel 玻璃镶条glass reinforced plastics 玻璃丝加强塑料glazing 装玻璃的,镶玻璃的gloss finish 光泽处理glued connection 粘结glued wood 胶合板gold coated 镀金的gold plated 镀金的gondola lift 架空缆车,架空索道goods lift 载货电梯goods passwnger lift 客货两用电梯goods paternoster 货用斗式升降机government inspection 政府部门验收governor 限速器governor bracket 限速器架governor cable 限速器绳governor catch 限速器夹钳governor overspeed switch 限速器超速开关governor rope 限速器绳governor rope grip jaw 限速器卡绳governor rope releasing carrier 限速器释放托架governor rope tension sheave 限速器绳张紧轮governor safety fence 限速器安全网罩governor sheave 限速器绳轮governor switch 限速器开关governor tension pulley 限速器张紧轮governor tension sheave 限速器绳张紧轮governor tension weights 限速器张紧轮铊governor tripping speed 限速器动作速度governor valve 限速阀grade of tolerance 公差等级Gradetz connection 格列茨电路gradual-clamp safeity 渐近式夹持安全钳graph 图表,曲线,图形graphic reflection equipment 图解影像装置grard cover 护盖gravity roller 重力滚轮gravity stopping distance 重力制动距离grdual wedge clamp safety 渐近式楔块夹持安全钳grease 黄油grease cup 黄油环grease gun 油枪grease nipple 油脂嘴grid 栅格线grid condenser 栅极电容器grid-condenser rectifier 栅控整流器grille 格栅窗grind 磨grinder 磨床grinding machine 磨床grinding paper 磨光纸groove 绳槽groove pitch 绳槽槽距groove pressure 绳槽压力groove profile 槽型groove sheave 有槽绳槽groove spacing 槽距grooving 绳槽gross area 总面积ground breaking 破土动工ground connection 接地ground floor 基层,底层ground leakage 地漏ground level 地面水平高度grounding 接地grounding conductor 接地引线grounding stud 接地螺柱grounding terminal 接地端子group 组,群,集团group automatic operation 梯群控制,群控group control supervisory panel 梯群监控盘group selective collective full automatic operation 组群集选全自动操作group supervision panel 群控监视屏group supervisory control 梯群监控group supervisory control algorithm 梯群监控规则系统group supervisory hall call control 梯群监控门厅呼梯系统group supervisory operation system 梯群监视操作系统grout angle 地坎支架支撑角钢grout channel 地坎支架支撑角钢GRP(glass reinforced plastics)玻璃丝加强塑料grub screw 平头螺丝GSP(group supervisory panel)梯群监控GTR(giant transistor)大功率晶体管guarantee period 保修期guaranteed leaking load of rope 钢丝绳许可漏去负载guard 护板,防护guard sheaver 防护轮guest lift 贵宾电梯guide 导轨guide rail bracket 导轨架guide rail clip 导轨压板guide rails 导轨guide rod 导向杆guide shoe 导靴guide shoe bush 导靴衬guide shoe gib 导靴镶条guide shoe insert 导靴衬guide shoe liner 导靴衬guiding 导引guiding pulley 导向轮gusset 连接板,角钢板hacksaw 锯子hair line 发纹hair-line finish 发纹处理hairline finished stainless steel 发纹处理不锈钢half wrap 半绕halfway junction box 中间接线盒hall 门厅,候梯厅hall buttons 召唤盒,呼梯按钮hall call 厅门呼梯hall call button 厅门呼梯按钮hall call cancel 厅门呼梯取消hall door 层门,厅门hall fixtures 门厅讯号装置hall landing 门厅停站hall lantern 厅外指示灯hall position indicator 层门指示灯hall station 门厅讯号装置hall stop 门厅呼梯停车hall wait passenger seconds 门厅候梯时间hall waiting time 门厅候梯时间hall way 门厅通道hammer 锤子hand drill 手电钻hand hammer 手锤hand lamp 手提灯hand operated 手动操作hand operated door 手动门hand powered lift 手动提升机hand pump 手压泵hand reset 手动复位hand rope 绳hands-on experence 实地经验handwheel 手动盘车装置,盘车手轮handwinding device 盘车手轮,手动盘hanger 悬吊器,吊门滑轮盒hanger plate 吊门板hanger rail 吊门轨道hanger roller 吊门滚轮hanger sheave 吊门轮hanger track 吊门轨道hanger trough 吊门槽板hard disc 硬盘hard wire 硬电线harden quench 硬淬hard-hat 安全帽hardware (计算机)硬件,(机械)标准件,五金件harm 损伤harmonic distortion 谐波失真harmonics 谐波harness 把,束hatch 围井(船用电梯井道)出口hatchway 井道hatchway enclosure 井道围封hatchway type elevator 井道式电梯hauling hope 曳引绳haunched beam 井道内牛腿,加腋梁hazard 危险HCR(highest call reversal)顶层呼梯反向head jamb 上门套,顶门套head room 顶房,顶部空间head room height 顶层高度head trim 上门套,顶门套header 上门坎,门顶部header case 门顶箱header cover 门顶罩header track 门上坎轨道,门顶部轨道headquarters 总部headroom height 顶层高度heat absorption 热量吸收heat accumulation 热量积聚heat dissipation 热量消耗heat emission 热量散发heat output 热量输出heat transfer 传感器,热传导heat treatment 热处理heater 发热器heating device 取暖器heatsink 散热片heavy demand floor 繁忙楼层heavy demand floor call 繁忙楼层呼梯heavy demand floor control 繁忙楼层控制heavy duty dloor 繁忙楼层heavy duty dloor call 繁忙楼层呼梯heavy duty dloor control 繁忙楼层控制heavy duty traffic 繁忙交通heavy duty zone 繁忙区域heavy traffic 繁忙交通heavy-duty 大载重,交通繁忙height above the hightest level 顶层高度helical 螺旋的helical gear 斜齿轮的,斜齿轮传动的,螺旋齿轮helical gear machine 斜齿轮曳引机helical gear reducer 斜齿轮减速器helical machin 斜齿轮曳引机helical speed reduction gear 斜齿轮减速机helical spring 螺旋弹簧helper 助手,帮工hemp core 麻芯hemp rope 麻绳hemp rope core 大麻绳芯hermetically sealed 气封的Hertz(Hz)赫兹(频率单位,周/秒)hex head bolt(HHB)六角螺栓hex screw 六角螺钉hexagon head 六角头hexagonal screw 六角螺钉high efficiency 高效率的high frequency chopping 高频斩波high gain 高增益high grade 高级的high pressure rubber hose 高压胶皮管high pressure rubber hydraulic hose 高压橡胶液压管high rise building 高层建筑high rise elevator 高层电梯high rise escalator 大高度自动扶梯high rise lift 高层电梯high rise zone 高层区high signal-noise ratio 高信号噪声比high speed escalator 高速自动扶梯high speed steel 高速钢high speed winding 高速绕组high tension 高张力high tension bolt 耐拉螺栓,强力螺栓high tension supply 高电压higher harmonics 高次谐波highest call reversal (HCR)顶层呼梯反向highest reversal floor 最高反向楼层highlighting bar (计算机)强光线条,重点线条high-speed slevator/lift 高速电梯hight 高度hilti bolt 膨胀螺栓hinge 铰链hinge door 铰链门,外敞门hinge plate 铰链板hinged platform sill 轿箱铰接式地坎hitch plate 钢丝绳绳头夹板hitch rod 绳头杆hob 滚刀hobbing 滚铣齿hobbing machine 滚齿机hohder 固定架hoist 起重器hoist machine 提升机,曳引机hoist ropes 曳引绳hoist ropes ratio of lift 电梯曳引绳曳引比hoisting cable 曳引绳hoisting machine 提升机,曳引机hoisting motor 曳引电动机hoisting rope 曳引绳hoistway 井道hoistway access switch 井道通道开关hoistway door 厅门hoistway door catch 门厅挈,厅门捕捉器hoistway door electric contact 井道门触点hoistway door interlock 厅门联锁装置hoistway door lock device 厅门门锁装置hoistway door mechanical lock 厅门机械锁hoistway enclosure 井道围封hoistway equipment 井道设备hoistway rope 起重绳hoistway sill aprope 厅门地坎裙板hoistway sill guard 厅门地坎护板hoistway telltale 井道内信号灯hoistway wall 井道壁,井道墙hoistway wiring harness 井道内把线holding time 保持时间hole 孔hole base system 基孔制hole countersunk 沉孔holeless 无孔的,无孔式hollow guide rail 空心导轨hollow rivet 空心铆钉home car 驻停轿箱,停在基站的轿箱home elevator/lift 家用电梯home floor 驻停楼层,基站home landing 基站hood 挡板hook 钩,圈horizontal 水平horizontal axis 水平轴horizontal elevator 水平电梯horizontal projection 水平投影horizontal seismic force 水平地震力horizontal shaft governor 横轴式限速器horizontal transportation 水平运输horizontally sliding door 水平滑动门horizontally step run 梯级水平移动距离hose 软管hose connector 软管连接器hose coupling 软管接头hose fitting 软管接头hose proof 软管套hospital elevator 病床梯host 主机,宿主hostile environments 有害环境hotel 旅馆hourly rate 小时定额housing 套hub 轮毂,中心hudraulic lift 液压电梯hum 嗡嗡声human interface 人机界面human safety 人身安全humidity 湿度hung door 悬吊门hydrant 消防栓,消防龙头hydraulic 液压的hydraulic buffer 油压缓冲器,耗能型缓冲器hydraulic drive 液压驱动hydraulic driving machine 液压驱动机hydraulic equipment 液压梯,液压设备hydraulic fluid 液压用液体hydraulic hose 液压软管hydraulic installation 液压设备hydraulic jack 液压千斤顶hydraulic lift nominal speed of up (down)motion 液压梯上(下)行额定速度hydraulic lift of directly-pushed 直顶式液压梯hydraulic lift of double 倍率液压梯hydraulic oil 液压油hydraulic parts 液压件hydraulic piping 液压配管hydraulic power unit 液压泵站hydraulic pump 液压泵hydraulic relevelling device 液压再平层装置hydraulic valve 液压阀I-bar 工字钢I-beam 工字梁idea 想法,概念,意见ideal 理想的identical 相同的identification 鉴定,鉴别identification tag 标签idler pulley 空转轮,惰轮idler sheave 惰轮IGBT(isolated grid binary transistor)隔离双栅极晶体管ignition voltage 点火电压illuminate 透明,透光illuminated button 发光按钮illumination 照明illustrated sheet 图解说明iluminate ceiling 透光吊顶immunity 抗干扰度impact 冲击impact load 冲击载荷impact loading to pit floor 底坑地面冲击载荷impedance 阻抗imperfection 不完整性,缺陷imperforate 无孔洞的imperial system 英制impregnation 注入,饱和impulse generator 脉冲发生器impulse processing 脉冲处理in car inspection 轿内检修in service 服务中,运行中in use 在使用中inaccessible 准入内inadvertent operation 粗心大意操作incandescent lamp 白炽弧光灯incandescent tube 白炽灯管inch 英寸inching 点数inching button 点动按钮inching feature 点动,微动inching switch 点动开关incident 事件inclination 倾斜度incline 斜面incline section 倾斜部分inclined elevator 倾斜式电梯inclined lift 倾斜式电梯inclined wheel chair lift 倾斜式轮椅电梯incombustible 非易燃的,不燃的incoming panel 受电盘incoming traffic 进入交通,来到交通increase 增加increment disk 增加盘increment pulse generator 增量盘脉冲发生器independent operation 独立操作independent service 独立服务indicatiing lamp 指示灯indicating arrow 指示箭头indicating circuit 指示电路indicating electrical instrument 指示型电气仪表indication contral 显示控制indicator 指示器indicator device 指示装置indicator face plate 指示器(灯)面板indicator for stop 层站指示器indicator lamp 指示灯indicator machine 指示器(灯)机械indirect 间接的indirect acting hyfraulic lift 间接式液压梯indirect back plunger 柱塞后置式indirect side plunger 柱塞侧置式indirectly heated cathod 旁热式阴极indirect-plunger hydraulic elevator 间接柱塞式液压梯induced 感应的inductance 电感induction asynchtonous motor 感应异步电动机induction furnace 感应电炉induction motor 感应电动机inductor 电感inductor plate 感应器板inductor replay 感应继电器industrial building 工业建筑物industrial plant 工业工厂industrial television 工业电视机industry 工业iner ledge 内凹缘(壁架)inertia 转动惯量infermation 信息information apparatus 信息器件,信息装置information transmitter 信息传送器infra-red multi-beam screen detector 红外线光幕检查器,电眼infrared ray 红外线in-ground 掩埋式initial excitation timer 额外励磁时间initial failure 初期故障initial position 起始位置initial setting 初期设定initialization 初始化(计算机)预置initialization travel 起始运行inlet 入口,吸收inlet guard 入口护板inlet of handrail 扶手带入口inlet switch 扶手带入口开关inner deck 内侧盖板inoperative 不运行,不工作inoperative position 不工作位置input 输入input signal 输入信号inrush current 冲击电流,启动电流insert 插件,井道预埋件insert nut 嵌入螺母inserting mortar 添缝insopection traveling speed 检修运行速度inspection 检查,检修inspection button 检修按钮inspection control 检修控制inspection control device 检修控制装置inspection device on top of the car 轿箱检修装置inspection door 检修门inspection operation 检修操作inspection speed 检修速度inspection switch 检修开关inspection trap 检修用活板门inspection travel 检修运行inspector 检测人员,验收机构inspector knife switch 检修闸刀开关installation 安装installation documents 安装文件installation drawing 安装图纸installation instructions 安装说明书installation manager 安装经理installation period 安装周期installation personnel 安装人员installation superintendent 安装总监installer 安装工instantaneous 瞬时的,瞬息的instantaneous safety 瞬时式安全钳instantaneous safety gear 瞬时式安全钳装置instantaneously type safety gear 瞬时式安全钳institute building 公共事业机构性建筑instructed person 受过训练的人员instruction 指示,指令instruction drawing 要领图instruction ROM 指令寄存器instruction system 指令系统instruction user 经训练的使用者instrument 仪器,仪表insulating coupling 绝缘接头insulating material 绝缘材料insulating resistance 绝缘电阻insulating sleeve 绝缘套管insulating strength 绝缘强度insulating tape 绝缘带insulation 绝缘insulation class 绝缘等级insulation rubber 防震橡胶,绝缘橡胶insulation test 绝缘试验insulator 绝缘子,电瓷integrate 积分,整化,结合integrated circuit 集成电路integrating electronic element 集成电子元件integrating error 累计误差intense traffic 密集交通,繁重交通intense up peak 上行密集交通intensive duty traffic 密集客流,繁重交通intensive traddic 稠密交通intercom device 对讲装置interconnect elevator 并联梯interface 接口,界面interference 干扰interference suppression 消除干扰interfloor balance traffic 楼层间平衡交通interfloor distance 层间距离interfloor flight time 层间运行时间interfloor height 层间高度interfloor jump time 层间跨越时间interfloor passenger arrival-rate 层间乘客到站率interfloor passenger traffic 层间客流交通interfloor traffic 层间交通,中间楼层交通interfloor traffic mode 中间楼层交通模式interim payment 分期付款interior 内部interior circuit 内绕圈interior decoration 内部装潢interior panel 内侧板interior paneling 护壁板,护栏板interior profile 内侧盖板interlock 门联锁interlock circuit 互锁电路interlock switch 联锁开关interlocking contact 联锁触点interlocking device 联锁装置interlocking element 联锁元件interlocking motor 联锁电动机intermediate floor 中间楼层intermediate landing 中间层站intermediate machine room 中间机房intermediate speed 中间速度intermediate stop 中间停车,中间停站intermediate support 中心支撑,中间支撑,第三支撑intermediate support beam 中间支撑架intermediate tie-bracket 中间束架intermittent 间歇的,周期性的intermittent problem 间歇性的问题,时有时无的问题intermittent service 间隙运行internal fault 内部故障internal gear 内齿轮internal resistance 内阻internal soore apparaus 内部存储器internal stress 内应力internal traffic 内部交通international safety standard 国际安全标准interphone 对讲机interpole 中间极interpole coil 附加磁极线圈interpole winding 换向极绕组interruption control 中断控制interstice 间隙interval 间隔introductory message 引导信息inventory 库存inventory verification 库存盘点inverse current 反向电流inverse proportion 成反比例inverse ratio 反比inverter 逆变器,变频器inverter control 逆变器控制inverter panel 逆变器盘investigation 调查研究invoice 发票invoicing 结账involuntary operation 偶然性操作involute tooth 渐开线齿iope slippage 绳滑移,绳打滑IPM (incidental phase modulation) 偶发的相位控制IPM (intelligent power module) 智能化电力模块,智能功率元件iron ore 铁矿iron vronze 铁青铜irregular 不规则的irregularity 不匀度irreversibility 不可逆性irreversible 不可逆的I-section 工字钢截面I-shape 工字形ISO 国际化标准组织isolate 分离isolation 隔离isolation pad 隔离垫isolation rubber 隔震橡胶item 项目jack 插座jack bottom sheave 液压千斤顶底部滑轮jack bracket 液压千斤顶支架jack stand 液压千斤顶底座jam nut 锁紧螺母jamb 门窗侧柱jamb protector 门套保护jamming 夹住,阻塞jaw 爪jerk 跳动,颠簸jerk rate 速度曲线光滑度jerk value 跳动量jerky stopping 有抖动停车jewel 晶体玻璃,聚脂玻璃jib crane 摇臂吊车jig (电梯安装)样板,架,夹具jiont strip 压条,接口条jionting ring] 连接环jionting sheet 连接板jiost 工字钢jobsite 工地joint 连接joint ball 万向球接joint seat 连接密封journal 轴颈journey 旅行,行程journey counter 行程计数表journey time 运行时间judgment 选择,判断jump out 短接,跨接jump time 跨接时间jumper 短接线,跨接线夹junction 接线junction box 接线盒kelometer 千米key 键key board 键盘key contact 钥匙触头key operation 钥匙开关key seat 键槽key swetch board 钥匙开关盒key switch 钥匙开关key switch box 钥匙开关盒key-operated switch 钥匙开关keypad 键板,键盘keyway 键槽kg 千克kick p;ate 踢脚板kicker shim 切槽垫片kiloohm 千欧姆kilowatt 千瓦特kilowatt-hour 千瓦小时kine 凯恩kinetic energy 动能kink 纽接knife edge switch 闸刀开关knob handle 球形手柄"KVA,Kva" 千伏安label 标签,标牌labeling 加标签,贴标签laboratory report 试验报告labour department inspection 劳动部门检查(验收)lacquer coat 漆层lacquer enamel 搪瓷漆ladder 梯子ladder diagram 梯形图lading door dill 厅门地坎lading door safety switch 层门安全开关laminated 层压的,叠压的laminated glass 多层玻璃laminated p;astic panel 层压塑料板,多层塑料板laminated plastic 层压塑料板laminated spring 叠簧laminated wood 多层板lamination 铁芯叠片lamp 灯lamp holder 灯座lamp socket 灯座landic panel 停电自动平装置landing 层站landing apron 厅门护脚板landing button 停站按钮landing call 层站呼梯landing call adder unit 层站呼梯信号加法网络装置landing call button 层站呼梯按钮landing call protection 层站呼梯信号保护landing device 停站装置landing direction indicator 层门方向指示灯landing door 层门,厅门landing door jamb 层门门套landing door locking device 厅门门锁装置landing entrance 层站入口landing indicatior of maching room 机房层站指示器landing indicator 层门指示灯landing interlock 厅门联锁landing plate 门厅板landing position indicator 层站位置指示器landing sagety edge 层门安全开关landing sills 层门地坎landing stop 层站停车landing switch 层站开关landing wiring harness 厅门接线束landing zone 层站区lang lay 同向捻股langding accuracy 停站精度,平层精度lantern 信号灯lap 研磨lap joint 搭接larallel single bank arrangement 重叠配置large quantity production 大量生产large scale production 大规模生产latch nut 锁紧螺母latching relay 门栓继电器lateral 横向的,水平的lathe 车床lay (绳)捻,编lay of rope (钢丝绳)捻股方法layout 布置,平面图layout drawing 布置图LCD 液晶显示器LCR 最低层呼梯反向LD 逻辑器件,逻辑装置lead 引线,导程,螺距lead 铅lead seal 铅封lead time 供货周期leaf 片,叶,门扇leaf spring 片簧leaflet 散页印刷品leakage 泄漏leakage coefficient 漏磁系数leakage current 泄漏电流leaving passenger 出梯乘客LED 发光二极管ledge 架,支架left hand machine 左手曳引机left hand two speed sliding door 左开门left handed worm 左旋螺杆left lay 左捻(绳股)left opening two speed sliding door 左开双扇门left-hand twist (绳)左向绞legible 易读的length 长度lens 透镜letter of credit 信用证letter of intent 意向书level "场水平,高度"level gear 伞齿轮level transducer 平层传感器leveling 平层leveling accuracy 平层准确度leveling cam 平层碰铁leveling device 平层装置leveling error 平层误差leveling inaccracy 平层误差leveling inductor plate 平层感应板leveling mode 平层模式leveling speed 平层速度,爬行速度leveling switch 平层开关leveling zone 平层区leveling-in zone 平层区lever 手柄,杆lever drive 手柄驱动lever handle 杆式手柄liability to guarantee 担保责任license 许可证license agreement 许可证协议license contract 许可证合同license fee 许可证费用license holder 许可证持有者license plate 使用许可,汽车牌licensee 持有许可证(执照者)lift 电梯lift attendant 电梯司机lift car 轿厢lift controil valve 升降控制阀lift cycle 电梯运行周期lift group control 电梯的群控lift in use indicator 电梯在使用中指示器lift inspector 电梯检查员lift machine 电梯曳引机lift management 电梯管理lift on ships 船用电梯lift series 电梯系列型谱lift tester 电梯测试员lift well 电梯井道lifting cam for sagety shoe (门)安全触板缩回凸轮lifting capacity 提升能力lifting height 提升高度lifting height of lift 电梯提升高度lifting hook 起重吊钩liftwell 电梯井道light beam safety switch 光线安全开关light bulb 灯泡light device of pit inspection 底坑检修照明装置light duty traffic 轻量交通light metal 轻金属light switch 照明开关light traffic 轻闲交通lighting 照明lighting circuit 照明电路lighting current 照明电流lighting fixture 灯具lighting source 照明电源lighting voltage 照明电压lighting window 采光窗户lightweight 重量轻的,轻质的lightweight concrete 轻质混凝土lighyting barrier 照明障碍limit curve 临界曲线limit switch 限位开关limiting circuit 限制电路line diagram 线图表line filter 管道过滤器line motor 直线电机line spacing 行距line voltage 线电压linear circuit 线性电路linear induction motor(LIM) 直线感应电动机linear speed 线速度liner 衬套lining 衬套link 链环,链节link library 程序库linkage 连杆linkage address 联系地址linkage specification 连杆规格表lintel 门楣liquid 液体liquid level 液位liquid level detector 液位检查器liquid level indicator 液位指示器list of materials 材料清单list of parts 零件清单live load 活动负荷living expenses 生活费用L-Key 内六角扳手ln-off signal 通断信号loac curve 载荷曲线load 负载,载量(数据,程序等)装入load cell 称重装置load condition 载重状态load measuring 杆量,称量load measuring choke coil 称量扼流线圈load measuring device 称重装置load measuring sensor 载重传感器load test 载重试验load transducer 载重传感器load weighing 称量load weighing floor 称量轿底load weighing platform 称量轿底load weighting device 称重装置loading 负载,负荷loading internal 乘客间隙时间loading internal timeloading time 进入电梯时间,装载时间loading weight 载重量lobby 楼厅,候梯厅lobby panel 门厅调度盘lobby surveillance 门厅检测装置local code 当地规定local lighting 局部照明local quench 局部淬火local regulation 当地规定local zone 本层楼区lock bolt 锁紧螺栓lock device 锁住装置lock down sagety 向下锁定安全装置lock net 锁母lock out operation 分离运转,分离操作lock striker 门锁碰头lock washer(L/W) 斜垫片lockable 可闭锁的,可锁定的locker 摇杆,锁紧器lock-in circuit 自保电路locking jaw 锁紧爪locking relay 自锁继电器locks 门锁装置,联锁装置log diary 运行日记logger 记录器logic analyser 逻辑分析器logic circuit 逻辑电路logic diagram 逻辑图logic element 逻辑元件logical combination 逻辑结合long ton 长吨,英制吨long wait hall call 候梯时间较长的门厅呼梯long wait landing call 候梯时间较长的层站呼梯longitudinal 纵向的Long's lay rope 同向捻(顺捻)钢丝绳loop 环圈loop circuit 环形电路loop current 环流loose bearing 松配轴承loose fit 动配合loss 损耗loss of power 功率损耗loudness level 响度louver 气窗low carbon steel 低碳钢low cost 低成本的,廉价的low rise building 低层建筑物low speed 低速的,慢速的low speed winding 低速绕组lower chord 下楔材料lower cost solution 低成本方案lower frame 底部框架lower/upper landing (自动扶梯)下部/上部通道lowest call reversal(LCR) 最低层呼梯反向lowest reversal floor 最低反向楼层low-rise lift group 低层区电梯组群low-rise zone 低层区low-speed door 低速门LS(limit switch) bracket 限位开关支架LS(limit switch) cam 限位开关碰铁lubricant 润滑剂lubricating fitting 润滑装置lubricating instructions 润滑说明书lubrication 润滑lubrication ring 润滑油杯lubricator 润滑器lug 线桥luggage lift 行李电梯lumen 流明(光通量单位)luminous indicator 发光指示器Lux 勒克司(照明单位)luxury car 豪华轿厢machinability 切削性machine 曳引机machine beam 曳引机承重钢梁machine beam plate 曳引机支撑板machine bed 曳引机座machine bed inserting mortar 曳引机座(砂浆)灌缝machine bed plate 机器底板,曳引机底板machine driving 曳引机machine earthquake proof stopper 曳引机防震挡止器machine elevation device 曳引机高度调整装置machine frame 曳引机架machine installation 曳引机安装machine isolation 曳引机隔震machine isolation device 曳引机隔震装置machine language 机器语言machine No. plate 曳引机编号牌machine room 机房machine room area 机房面积machine room arrangement 机房布置machine room depth 机房深度machine room height 机房高度machine room inspection 机房检修machine room lower 下机房machine room of hydraulic lift 液压电梯机房machine room plan 机房布置图machine room upper 上机房machine room width 机房宽度machine room wiring harness 机房配线束machine sheave cover 曳引机绳轮罩machine spacing bed 曳引机高度调整底座machine supporing steels 曳引机承重钢楔machine supporting beams 承重梁machine supporting steelwork 曳引机承重钢结构machine tools 机床machined 机加工的machinery 机械machining 机械加工machining allowance 加工余量machining in general 普通机械加工magnet 磁条magnet brake 磁力制动器magnet coil 电磁线圈magnet lamination 电磁铁芯片magnet plunger 插棒式电磁magnet vane 隔磁板magnetic amplifier 磁放大器magnetic brake 电磁制动器magnetic catch 磁闩magnetic charateristic 磁特性magnetic clutch 磁性离合器magnetic detector 磁力检查器magnetic flux 磁通量magnetic flux density 磁通密度magnetic leveling switch 磁性离合开关magnetic noise 电磁噪声magnetic pole 磁极magnetic resistance 磁阻magnetic switch 磁感应开关magnetism 磁性magnetism pole 磁棒magnitude 大小,数量,等级magntic core 磁铁芯mahogany 红木main chain 主链条main circuit 主电路main circuit breaker 主断路器main circuit control 主电路控制main contact 主触点main contactor 主接触器main drive 主驱动装置main drive chain 主驱动链main drive chain guard 主驱动链保护装置main drive shaft 主驱动轴。
电梯?LIFT;ELEVATOR?乘客电梯PASSENGER?LIFT?载货电梯GOODS?LIFT;FREIGHT?LIFT?客货电梯PASSENGER-GOODS?LIFT?病床电梯;医用电梯?BED?LIFT?住宅电梯?RESIDENTIAL?LIFT?杂物电梯?DUMBWAITER?LIFT;?SERVICE?LIFT?船用电梯?LIFT?ON?SHIPS?观光电梯PANORAMIC?LIFT;OBSERTION?LIFT?汽车电梯?MOTOR?VEHICLE?LLIFT;AUTOMBILE?LIFT? 液压电梯?HYRAULIC?LIFT?平层准确度过?LEVELING?ACCURACY?电梯额定速度?RATED?SPEED?OF?LIFT?检修速度?INSPECTION?SPEED?额定载重量?RATED?LOAD;RATED?CAPACITY?电梯提升高度?TRAVELING?HEIGHT?OF?LIFT;LIFTING?HEIGHT?OF?LIFT?机房高度MACHINE?ROOM?HEIGHT?机房宽度?MACHINE?ROOM?HEIGHT?机房宽度?MACHINE?ROOM?DEPTH?机房面积?MACHINE?ROOM?AREA?辅助机房?SECONDARY?MACHINE?ROOM?;?隔层SECONDARY?FLOOR?滑轮间隔?PULLEY?ROOM?层站台票LANDING?层站入口?LANDING?ENTRANCE?基站?MAIN?LANDING;MAIN?FLOOR;HOME?LANDING? 预定基站?PREDETERMINED?LANDING?底层端站?BOTTOM?TERMINAL?LANDING?顶层端站?TOP?TERMINAL?LANDING?层间距离?FLOOR?TO?FLOOR?DISTANCE;INTERFLOOR?DISTANCE?井道WELL;SHAFT;HOISTWAY?单梯井道?SINGLE?WELL?多梯井道?MULTIPLE?WELL;COMMON?WELL?井道壁?WELL?ENCLOSURE;?SHAFT?WELL?井道宽度?WELL?WIDTH;SHAFT?WIDTH?井道深度?WELL?DEPTH;SHAFT?DEPTH?底坑PIT?底坑深度?PIT?DEPTH?顶层高度?HEADROOM?HEIGHT;HEIGHT?ABOVE?THE?HIGHEST?LEVEL?SERVED;TOP?HEIGHT? 井道内牛腿;加腋梁?HAUNCHED?BEAM?围井?TRUNK?围井出口?HATCH?开锁区域?UNLOCKING?ZONE?平层?LEVELING?平层区?LEVELING?ZONE?开门宽度?DOOR?OPENINGWIDTH?轿厢入口?CAR?ENTRANCE?轿厢入口净尺寸?CLEAR?ENTRANCE?TO?THE?CAR?轿厢宽度CAR?WIDTH?轿厢深度?CAR?DEPTH?轿厢高度?CAR?HEIGHT?电梯司机LIFT?ATTENDANT?乘客人数?NUMBER?OF?PASSENGER?油压缓冲器工作行程?WORKING?STROKE?OF?OIL?BUFFER?弹簧缓冲器工作行程?WORKING?STROKE?OF?SRING?BUFFER? 轿底间隙?BOTTOM?CLEANCES?FOR?CAR?轿顶间隙?TOP?CLEARANCES?FOR?COUNTERWEIGHT?对重装置顶部间隙?TOP?CLEARANCES?FOR?COUNTERXEIGHT?对接操作规程DOCKING?OPERATION?隔层停*操作?SKIP-STOP?OPERATION?检修操作规程?INSPECTION?OPERATION?电梯拽引型式TRACTION?TYPES?OF?LIFT?电梯拽引机绳拽引?HOIST?ROPES?RATIO?OF?LIFT?消防服务FIREMAN?SERVICE?独立操作INDEPENDENT?OPERATION?缓冲器?BUFFER?油压缓冲器(耗能型缓冲器)?HYDRAULIC?BUFFER;OIL?BUFFER? 弹簧缓冲器;蓄能型缓冲器具SPRING?BUFFER?减振器具VIBRATING?ABSORBER?轿厢CAR?LIFT?CAR?轿厢底;轿底CAR?PLATRORM;PLATFORM?轿厢壁;轿壁?CAR?ENCLOSURES;CAR?WALLS?轿车厢顶;轿顶?CAR?ROOR?轿厢装饰顶?CAR?HANDRAIL?轿厢扶手CAR?HANDRAIL?轿顶防护栏杆?CAR?PROTECTION?BALUSTADE?轿厢架;轿架?CAR?FRAME?检修门?DOOR?OPERATOR?检修门?ACCESS?DOOR?手动门?MANUALLY?OPERATED?DOOR?自动门POWER?OPERATED?DOOR?层门;厅门?LANDING?DOOR;SHAFT?DOOR;HALL?DOOR? 防火层门;防火门?RIER-PROOF?DOOR?轿厢门;轿门CAR?DOOR?安全触板?SAFETY?EDGES?FOR?DOOR?铰链门;外敞门?HINGED?DOOR?栅栏门?COLLAPSIBLE?DOOR?水平滑动门?HORIZONTALLY?SLIDING?DOOR?中分门?CENTER?OPENING?DOOR?旁开门?TWO-SPEED?SLIDING?DOOR?双折门?TWO-PANEL?SLIDING?DOOR?双速门?TWO?SPEED?DOOR?左开门?LEFT?HAND?TWO?SPEED?SLIDING?DOOR?右开门?RIGHT?HAND?TWO?SPEED?SLIDING?DOOR?垂直滑动门VERTICALLY?SLIDING?DOOR?垂直中分门BI-PARTING?DOOR?拽引绳补偿装置?COMPENSATING?DEVICE?FOR?HOIST?ROPES? 补偿绳装置?COMPENSATING?ROPE?DEVICE?补偿绳防跳装置ANTI-REBOUND?OF?COMPENSATION?ROPE?DEVICE?地坎?SILL?轿厢地坎?CAR?SILLS;PLATE?THRESHOLD?ELEVATOR?层门地坎?LANDING?SILLS;SILL?ELEVATOR?ENTEANCE?轿顶检修装置?INSPECTION?DEVICE?ON?TOP?OF?THE?CAR?轿顶照明装置?CAR?TOP?LIGHT?底坑检修照明装置?LIGHT?DEVICE?OF?PIT?INSPECTION? 轿厢内指层灯;轿厢位置指示?CAR?POSITION?INDICATOR? 层门门套?LANDING?DOOR?JAMB?层门指示灯?LANDING?INDICATOR;HALL?POSITION?INDICATOR?层门方向指示灯?LANDING?DIRECTION?INDICATOR?控制屏?CONTROL?PANEL?控制柜?CONTROL?CABINET;CONTROLLER?操纵箱?OPERATION?PANEL?操纵盘?CAR?OPERATION?PANEL?警铃按钮?ALARM?BUTTON。
Guide rail 10mm (T75-3/B) with fish plate & screwT75-3/B型带有螺纹接合板的10毫米导轨Guide rail 15.88mm (T89/B) with fish plate & screwT89/B型带有螺纹接合板的15.88毫米导轨Guide rail 5mm (T50/A) with fish plate & screwT50/A型带有螺纹接合板的5毫米导轨Hollow guide rail (TH3, TH3A, TH5, TH5A) with fish plate & screwTH3, TH3A, TH5和TH5A型带有螺纹接合板的中空导轨Traction Machine TORIN SF 140 1MS 500 KG 5.5 KW通润SF140型曳引机1MS 载重量500 公斤; 功率5.5 千瓦Traction Machine TORIN FYJ 180, 1MS 630 KG通润FYJ 180型曳引机, 1MS载重量630 公斤Traction Machine HAISUNG (GT) China HSU 130,海星(GT) 曳引机(中国制造)HSU 130,Traction Machine HAISUNG China HSU 150G, 60m/min 750 KG & 900 KG海星(HSU)曳引机(中国制造)150G, 运行速度60米/分钟, 载重量750公斤-900公斤Other China Traction Machine 480 Kg to 900 Kg其他中国制造的曳引机:载重量480千克-- 900千克COP with 7 segment display & Intercom 6 stop, 7 stop….10 stop带有7段段码屏显示和6 层,7层…10层对讲系统的COPHOP with 7 segment display带有7段段码屏显示的HOP7 segment display7段段码屏显示Complete Inspection Box全面检查箱Over Speed Governor 1ms超速限速器1msSelcom Door operator with accessories 700mm & 800mm Without VVVF (AC2) speed with DC motor带有700毫米和800毫米无极调速器(AC2)的直流电机配置的西尔康门机Selcom Landing Header with accessories 700mm & 800mm配置700mm &和800mm???的西尔康层门头Genesis, Eshine or Anliso Door operator with accessories 700mm & 800mm VVVF & Without VVVF (AC2)配置700毫米和800毫米无极或单极调速器(AC2)的Genesis, 易升或安利索门机Genesis, Eshine or Anliso Landing Header with accessories 700mm & 800mm带有700mm & 800mm 配件的Genesis(公司名,懒得查了!)、易升或安利索层门头Standered 700mm & 800mm MS painted, Hairline SS, Mirror SS, Landing door标准700mm和800mm的烤漆不锈钢、发纹不锈钢和镜面刨光不锈钢分层门Flat Cable 12 core, 24 core, 36 core, 40 core, 48 core扁形电梯电缆:12 芯, 24芯, 36芯, 40芯, 48芯Yaskawa, Delta, and other Inverter with PG card and breaking resistance & filter, 5.5, 7.5, 10 KW安川变频器, 德尔塔变频器和其他带有PG卡的反应换流器,断接电阻和滤波器的功率:5.5, 7.5和10千瓦Complete control system (Mico Control, Wuxi Zhongxiu, Step or other reputed Manufacturer)全面控制系统(微控制公司, 无锡Zhongxiu(是否是中国?写错了?有名的制造商)Mother Board for control控制母板:Rope for elevator 8mm, 10mm, 12mm电梯钢丝绳:8mm, 10mm, 12mmDiversion pulley 400mm (you find this from Traction Machine Manufacturer)导向滑轮:400毫米(你可以找到该型号的曳引机制造商)Stainless Steel Sheet Hairline finish, Mirror Finish & Mirror Etching, 0.7mm, 0.8mm,1.0mm发纹处理、镜面抛光以及镜面蚀刻不锈钢片:0.7毫米,0.8毫米和1.0毫米Mirror Etching and hairline finish Elevator Car 1050 x 1100 mm镜面蚀刻和发纹处理的电梯罐笼1050毫米x 1100毫米Light curtain光幕保护voice announcement语音报站Intercom对讲系统Encoder电梯编码器Position Indicator电梯轿厢位置Emergency break system, Suspension road紧急逃生系统,悬挂装置Guide rail (电梯)导轨Traction Machine (电梯) 曳引机segment display (电梯)段码屏显示Over Speed Governor (电梯)超速限速器fish plate(电梯) 接合板, 鱼尾板HAISUNG韩国海星产电公司(韩国最大的专业曳引机厂家之一),中国分厂TORIN美国通润公司,中国分厂Intercom (电梯)对讲系统Selcom Door西尔康(公司名)门DC motor直流电机(马达)Eshine易升(公司名)Anliso安利索(公司名)Door operator(电梯) 门机stainless steel sheet Hairline finish发纹处理不锈钢片Mirror Finish镜面抛光Mirror Etching镜面蚀刻,Elevator Car 电梯罐笼Light curtain光幕保护voice announcement语音报站Encoder电梯编码器Position Indicator电梯轿厢位置Emergency break system紧急逃生系统, Suspension road悬挂装置Diversion pulley导向滑轮Rope for elevator电梯钢丝绳Micro Control微控制(公司名)yaskawa 安川Flat Cable扁形电梯电缆Landing door分层门MS painted, Hairline SS, Mirror SS(烤漆不锈钢,发纹不锈钢,镜面刨光不锈钢)gate 轿门,闸门电路,选通器gate action 选通作用gate amplifier 选通脉冲放大器gate bias 栅偏压gate closer 关门器gate contact 门触点gate controller 门控器gate diode 门电路二极管gate generator 门脉冲发生器gate guide shoe 门导靴gate lock 门锁gate operator 开关门机gate power operator 自动开关门机gate pulse 门脉冲gate sill 门地坎gate switch 门开关gate time 选通时间gate trigger 控制门触发器gate turnoff thyristor 可控硅开关gate vale 闸阀gauge 量规,量具gear 齿轮gear box 齿轮箱gear driving machine 有齿轮曳引机gear efficiency 机器效率,齿轮效率gear grease 齿轮黄油gear hobbing 滚齿gear parts 齿轮部分gear pump 齿轮泵gear ratio 传动比gear reducer 齿轮减速装置gear ring 齿轮圈gear speed reducer 齿轮减速装置gear teeth 轮齿geared elevator 有齿轮电梯geared hoising machine 有齿轮曳引机geared lift 有齿轮电梯geared machine 有齿轮曳引机geared motor 齿轮传动电动机gearless 无齿轮gearless driving machine 无齿轮曳引机gearless elevator 无齿轮电梯gearless hoisting machine 无齿轮曳引机gearless machine 无齿轮曳引机general contractor 总承包商general drawing 总图general sales overheads 一般销售开支generate 发电generator 发电机generator field control 发电机磁场控制generator self-excited field 发电机自激场generator set 发电机组germanium 锗germanium diode 锗二极管gib 镶条,衬垫,楔块gland 压盖,密封套glass 玻璃glass balustrade 玻璃扶栏glass elevator 观光电梯glass mounting bracket 玻璃支架glass panel 玻璃镶条glass reinforced plastics 玻璃丝加强塑料glazing 装玻璃的,镶玻璃的gloss finish 光泽处理glued connection 粘结glued wood 胶合板gold coated 镀金的gold plated 镀金的gondola lift 架空缆车,架空索道goods lift 载货电梯goods passwnger lift 客货两用电梯goods paternoster 货用斗式升降机government inspection 政府部门验收governor 限速器governor bracket 限速器架governor cable 限速器绳governor catch 限速器夹钳governor overspeed switch 限速器超速开关governor rope 限速器绳governor rope grip jaw 限速器卡绳governor rope releasing carrier 限速器释放托架governor rope tension sheave 限速器绳张紧轮governor safety fence 限速器安全网罩governor sheave 限速器绳轮governor switch 限速器开关governor tension pulley 限速器张紧轮governor tension sheave 限速器绳张紧轮governor tension weights 限速器张紧轮铊governor tripping speed 限速器动作速度governor valve 限速阀grade of tolerance 公差等级Gradetz connection 格列茨电路gradual-clamp safeity 渐近式夹持安全钳graph 图表,曲线,图形graphic reflection equipment 图解影像装置grard cover 护盖gravity roller 重力滚轮gravity stopping distance 重力制动距离grdual wedge clamp safety 渐近式楔块夹持安全钳grease 黄油grease cup 黄油环grease gun 油枪grease nipple 油脂嘴grid 栅格线grid condenser 栅极电容器grid-condenser rectifier 栅控整流器grille 格栅窗grind 磨grinder 磨床grinding machine 磨床grinding paper 磨光纸groove 绳槽groove pitch 绳槽槽距groove pressure 绳槽压力groove profile 槽型groove sheave 有槽绳槽groove spacing 槽距grooving 绳槽gross area 总面积ground breaking 破土动工ground connection 接地ground floor 基层,底层ground leakage 地漏ground level 地面水平高度grounding 接地grounding conductor 接地引线grounding stud 接地螺柱grounding terminal 接地端子group 组,群,集团group automatic operation 梯群控制,群控group control supervisory panel 梯群监控盘group selective collective full automatic operation 组群集选全自动操作group supervision panel 群控监视屏group supervisory control 梯群监控group supervisory control algorithm 梯群监控规则系统group supervisory hall call control 梯群监控门厅呼梯系统group supervisory operation system 梯群监视操作系统grout angle 地坎支架支撑角钢grout channel 地坎支架支撑角钢GRP(glass reinforced plastics)玻璃丝加强塑料grub screw 平头螺丝GSP(group supervisory panel)梯群监控GTR(giant transistor)大功率晶体管guarantee period 保修期guaranteed leaking load of rope 钢丝绳许可漏去负载guard 护板,防护guard sheaver 防护轮guest lift 贵宾电梯guide 导轨guide rail bracket 导轨架guide rail clip 导轨压板guide rails 导轨guide rod 导向杆guide shoe 导靴guide shoe bush 导靴衬guide shoe gib 导靴镶条guide shoe insert 导靴衬guide shoe liner 导靴衬guiding 导引guiding pulley 导向轮gusset 连接板,角钢板hacksaw 锯子hair line 发纹hair-line finish 发纹处理hairline finished stainless steel 发纹处理不锈钢half wrap 半绕halfway junction box 中间接线盒hall 门厅,候梯厅hall buttons 召唤盒,呼梯按钮hall call 厅门呼梯hall call button 厅门呼梯按钮hall call cancel 厅门呼梯取消hall door 层门,厅门hall fixtures 门厅讯号装置hall landing 门厅停站hall lantern 厅外指示灯hall position indicator 层门指示灯hall station 门厅讯号装置hall stop 门厅呼梯停车hall wait passenger seconds 门厅候梯时间hall waiting time 门厅候梯时间hall way 门厅通道hammer 锤子hand drill 手电钻hand hammer 手锤hand lamp 手提灯hand operated 手动操作hand operated door 手动门hand powered lift 手动提升机hand pump 手压泵hand reset 手动复位hand rope 绳hands-on experence 实地经验handwheel 手动盘车装置,盘车手轮handwinding device 盘车手轮,手动盘hanger 悬吊器,吊门滑轮盒hanger plate 吊门板hanger rail 吊门轨道hanger roller 吊门滚轮hanger sheave 吊门轮hanger track 吊门轨道hanger trough 吊门槽板hard disc 硬盘hard wire 硬电线harden quench 硬淬hard-hat 安全帽hardware (计算机)硬件,(机械)标准件,五金件harm 损伤harmonic distortion 谐波失真harmonics 谐波harness 把,束hatch 围井(船用电梯井道)出口hatchway 井道hatchway enclosure 井道围封hatchway type elevator 井道式电梯hauling hope 曳引绳haunched beam 井道内牛腿,加腋梁hazard 危险HCR(highest call reversal)顶层呼梯反向head jamb 上门套,顶门套head room 顶房,顶部空间head room height 顶层高度head trim 上门套,顶门套header 上门坎,门顶部header case 门顶箱header cover 门顶罩header track 门上坎轨道,门顶部轨道headquarters 总部headroom height 顶层高度heat absorption 热量吸收heat accumulation 热量积聚heat dissipation 热量消耗heat emission 热量散发heat output 热量输出heat transfer 传感器,热传导heat treatment 热处理heater 发热器heating device 取暖器heatsink 散热片heavy demand floor 繁忙楼层heavy demand floor call 繁忙楼层呼梯heavy demand floor control 繁忙楼层控制heavy duty dloor 繁忙楼层heavy duty dloor call 繁忙楼层呼梯heavy duty dloor control 繁忙楼层控制heavy duty traffic 繁忙交通heavy duty zone 繁忙区域heavy traffic 繁忙交通heavy-duty 大载重,交通繁忙height above the hightest level 顶层高度helical 螺旋的helical gear 斜齿轮的,斜齿轮传动的,螺旋齿轮helical gear machine 斜齿轮曳引机helical gear reducer 斜齿轮减速器helical machin 斜齿轮曳引机helical speed reduction gear 斜齿轮减速机helical spring 螺旋弹簧helper 助手,帮工hemp core 麻芯hemp rope 麻绳hemp rope core 大麻绳芯hermetically sealed 气封的Hertz(Hz)赫兹(频率单位,周/秒)hex head bolt(HHB)六角螺栓hex screw 六角螺钉hexagon head 六角头hexagonal screw 六角螺钉high efficiency 高效率的high frequency chopping 高频斩波high gain 高增益high grade 高级的high pressure rubber hose 高压胶皮管high pressure rubber hydraulic hose 高压橡胶液压管high rise building 高层建筑high rise elevator 高层电梯high rise escalator 大高度自动扶梯high rise lift 高层电梯high rise zone 高层区high signal-noise ratio 高信号噪声比high speed escalator 高速自动扶梯high speed steel 高速钢high speed winding 高速绕组high tension 高张力high tension bolt 耐拉螺栓,强力螺栓high tension supply 高电压higher harmonics 高次谐波highest call reversal (HCR)顶层呼梯反向highest reversal floor 最高反向楼层highlighting bar (计算机)强光线条,重点线条high-speed slevator/lift 高速电梯hight 高度hilti bolt 膨胀螺栓hinge 铰链hinge door 铰链门,外敞门hinge plate 铰链板hinged platform sill 轿箱铰接式地坎hitch plate 钢丝绳绳头夹板hitch rod 绳头杆hob 滚刀hobbing 滚铣齿hobbing machine 滚齿机hohder 固定架hoist 起重器hoist machine 提升机,曳引机hoist ropes 曳引绳hoist ropes ratio of lift 电梯曳引绳曳引比hoisting cable 曳引绳hoisting machine 提升机,曳引机hoisting motor 曳引电动机hoisting rope 曳引绳hoistway 井道hoistway access switch 井道通道开关hoistway door 厅门hoistway door catch 门厅挈,厅门捕捉器hoistway door electric contact 井道门触点hoistway door interlock 厅门联锁装置hoistway door lock device 厅门门锁装置hoistway door mechanical lock 厅门机械锁hoistway enclosure 井道围封hoistway equipment 井道设备hoistway rope 起重绳hoistway sill aprope 厅门地坎裙板hoistway sill guard 厅门地坎护板hoistway telltale 井道内信号灯hoistway wall 井道壁,井道墙hoistway wiring harness 井道内把线holding time 保持时间hole 孔hole base system 基孔制hole countersunk 沉孔holeless 无孔的,无孔式hollow guide rail 空心导轨hollow rivet 空心铆钉home car 驻停轿箱,停在基站的轿箱home elevator/lift 家用电梯home floor 驻停楼层,基站home landing 基站hood 挡板hook 钩,圈horizontal 水平horizontal axis 水平轴horizontal elevator 水平电梯horizontal projection 水平投影horizontal seismic force 水平地震力horizontal shaft governor 横轴式限速器horizontal transportation 水平运输horizontally sliding door 水平滑动门horizontally step run 梯级水平移动距离hose 软管hose connector 软管连接器hose coupling 软管接头hose fitting 软管接头hose proof 软管套hospital elevator 病床梯host 主机,宿主hostile environments 有害环境hotel 旅馆hourly rate 小时定额housing 套hub 轮毂,中心hudraulic lift 液压电梯hum 嗡嗡声human interface 人机界面human safety 人身安全humidity 湿度hung door 悬吊门hydrant 消防栓,消防龙头hydraulic 液压的hydraulic buffer 油压缓冲器,耗能型缓冲器hydraulic drive 液压驱动hydraulic driving machine 液压驱动机hydraulic equipment 液压梯,液压设备hydraulic fluid 液压用液体hydraulic hose 液压软管hydraulic installation 液压设备hydraulic jack 液压千斤顶hydraulic lift nominal speed of up (down)motion 液压梯上(下)行额定速度hydraulic lift of directly-pushed 直顶式液压梯hydraulic lift of double 倍率液压梯hydraulic oil 液压油hydraulic parts 液压件hydraulic piping 液压配管hydraulic power unit 液压泵站hydraulic pump 液压泵hydraulic relevelling device 液压再平层装置hydraulic valve 液压阀I-bar 工字钢I-beam 工字梁idea 想法,概念,意见ideal 理想的identical 相同的identification 鉴定,鉴别identification tag 标签idler pulley 空转轮,惰轮idler sheave 惰轮IGBT(isolated grid binary transistor)隔离双栅极晶体管ignition voltage 点火电压illuminate 透明,透光illuminated button 发光按钮illumination 照明illustrated sheet 图解说明iluminate ceiling 透光吊顶immunity 抗干扰度impact 冲击impact load 冲击载荷impact loading to pit floor 底坑地面冲击载荷impedance 阻抗imperfection 不完整性,缺陷imperforate 无孔洞的imperial system 英制impregnation 注入,饱和impulse generator 脉冲发生器impulse processing 脉冲处理in car inspection 轿内检修in service 服务中,运行中in use 在使用中inaccessible 准入内inadvertent operation 粗心大意操作incandescent lamp 白炽弧光灯incandescent tube 白炽灯管inch 英寸inching 点数inching button 点动按钮inching feature 点动,微动inching switch 点动开关incident 事件inclination 倾斜度incline 斜面incline section 倾斜部分inclined elevator 倾斜式电梯inclined lift 倾斜式电梯inclined wheel chair lift 倾斜式轮椅电梯incombustible 非易燃的,不燃的incoming panel 受电盘incoming traffic 进入交通,来到交通increase 增加increment disk 增加盘increment pulse generator 增量盘脉冲发生器independent operation 独立操作independent service 独立服务indicatiing lamp 指示灯indicating arrow 指示箭头indicating circuit 指示电路indicating electrical instrument 指示型电气仪表indication contral 显示控制indicator 指示器indicator device 指示装置indicator face plate 指示器(灯)面板indicator for stop 层站指示器indicator lamp 指示灯indicator machine 指示器(灯)机械indirect 间接的indirect acting hyfraulic lift 间接式液压梯indirect back plunger 柱塞后置式indirect side plunger 柱塞侧置式indirectly heated cathod 旁热式阴极indirect-plunger hydraulic elevator 间接柱塞式液压梯induced 感应的inductance 电感induction asynchtonous motor 感应异步电动机induction furnace 感应电炉induction motor 感应电动机inductor 电感inductor plate 感应器板inductor replay 感应继电器industrial building 工业建筑物industrial plant 工业工厂industrial television 工业电视机industry 工业iner ledge 内凹缘(壁架)inertia 转动惯量infermation 信息information apparatus 信息器件,信息装置information transmitter 信息传送器infra-red multi-beam screen detector 红外线光幕检查器,电眼infrared ray 红外线in-ground 掩埋式initial excitation timer 额外励磁时间initial failure 初期故障initial position 起始位置initial setting 初期设定initialization 初始化(计算机)预置initialization travel 起始运行inlet 入口,吸收inlet guard 入口护板inlet of handrail 扶手带入口inlet switch 扶手带入口开关inner deck 内侧盖板inoperative 不运行,不工作inoperative position 不工作位置input 输入input signal 输入信号inrush current 冲击电流,启动电流insert 插件,井道预埋件insert nut 嵌入螺母inserting mortar 添缝insopection traveling speed 检修运行速度inspection 检查,检修inspection button 检修按钮inspection control 检修控制inspection control device 检修控制装置inspection device on top of the car 轿箱检修装置inspection door 检修门inspection operation 检修操作inspection speed 检修速度inspection switch 检修开关inspection trap 检修用活板门inspection travel 检修运行inspector 检测人员,验收机构inspector knife switch 检修闸刀开关installation 安装installation documents 安装文件installation drawing 安装图纸installation instructions 安装说明书installation manager 安装经理installation period 安装周期installation personnel 安装人员installation superintendent 安装总监installer 安装工instantaneous 瞬时的,瞬息的instantaneous safety 瞬时式安全钳instantaneous safety gear 瞬时式安全钳装置instantaneously type safety gear 瞬时式安全钳institute building 公共事业机构性建筑instructed person 受过训练的人员instruction 指示,指令instruction drawing 要领图instruction ROM 指令寄存器instruction system 指令系统instruction user 经训练的使用者instrument 仪器,仪表insulating coupling 绝缘接头insulating material 绝缘材料insulating resistance 绝缘电阻insulating sleeve 绝缘套管insulating strength 绝缘强度insulating tape 绝缘带insulation 绝缘insulation class 绝缘等级insulation rubber 防震橡胶,绝缘橡胶insulation test 绝缘试验insulator 绝缘子,电瓷integrate 积分,整化,结合integrated circuit 集成电路integrating electronic element 集成电子元件integrating error 累计误差intense traffic 密集交通,繁重交通intense up peak 上行密集交通intensive duty traffic 密集客流,繁重交通intensive traddic 稠密交通intercom device 对讲装置interconnect elevator 并联梯interface 接口,界面interference 干扰interference suppression 消除干扰interfloor balance traffic 楼层间平衡交通interfloor distance 层间距离interfloor flight time 层间运行时间interfloor height 层间高度interfloor jump time 层间跨越时间interfloor passenger arrival-rate 层间乘客到站率interfloor passenger traffic 层间客流交通interfloor traffic 层间交通,中间楼层交通interfloor traffic mode 中间楼层交通模式interim payment 分期付款interior 内部interior circuit 内绕圈interior decoration 内部装潢interior panel 内侧板interior paneling 护壁板,护栏板interior profile 内侧盖板interlock 门联锁interlock circuit 互锁电路interlock switch 联锁开关interlocking contact 联锁触点interlocking device 联锁装置interlocking element 联锁元件interlocking motor 联锁电动机intermediate floor 中间楼层intermediate landing 中间层站intermediate machine room 中间机房intermediate speed 中间速度intermediate stop 中间停车,中间停站intermediate support 中心支撑,中间支撑,第三支撑intermediate support beam 中间支撑架intermediate tie-bracket 中间束架intermittent 间歇的,周期性的intermittent problem 间歇性的问题,时有时无的问题intermittent service 间隙运行internal fault 内部故障internal gear 内齿轮internal resistance 内阻internal soore apparaus 内部存储器internal stress 内应力internal traffic 内部交通international safety standard 国际安全标准interphone 对讲机interpole 中间极interpole coil 附加磁极线圈interpole winding 换向极绕组interruption control 中断控制interstice 间隙interval 间隔introductory message 引导信息inventory 库存inventory verification 库存盘点inverse current 反向电流inverse proportion 成反比例inverse ratio 反比inverter 逆变器,变频器inverter control 逆变器控制inverter panel 逆变器盘investigation 调查研究invoice 发票invoicing 结账involuntary operation 偶然性操作involute tooth 渐开线齿iope slippage 绳滑移,绳打滑IPM (incidental phase modulation) 偶发的相位控制IPM (intelligent power module) 智能化电力模块,智能功率元件iron ore 铁矿iron vronze 铁青铜irregular 不规则的irregularity 不匀度irreversibility 不可逆性irreversible 不可逆的I-section 工字钢截面I-shape 工字形ISO 国际化标准组织isolate 分离isolation 隔离isolation pad 隔离垫isolation rubber 隔震橡胶item 项目jack 插座jack bottom sheave 液压千斤顶底部滑轮jack bracket 液压千斤顶支架jack stand 液压千斤顶底座jam nut 锁紧螺母jamb 门窗侧柱jamb protector 门套保护jamming 夹住,阻塞jaw 爪jerk 跳动,颠簸jerk rate 速度曲线光滑度jerk value 跳动量jerky stopping 有抖动停车jewel 晶体玻璃,聚脂玻璃jib crane 摇臂吊车jig (电梯安装)样板,架,夹具jiont strip 压条,接口条jionting ring] 连接环jionting sheet 连接板jiost 工字钢jobsite 工地joint 连接joint ball 万向球接joint seat 连接密封journal 轴颈journey 旅行,行程journey counter 行程计数表journey time 运行时间judgment 选择,判断jump out 短接,跨接jump time 跨接时间jumper 短接线,跨接线夹junction 接线junction box 接线盒kelometer 千米key 键key board 键盘key contact 钥匙触头key operation 钥匙开关key seat 键槽key swetch board 钥匙开关盒key switch 钥匙开关key switch box 钥匙开关盒key-operated switch 钥匙开关keypad 键板,键盘keyway 键槽kg 千克kick p;ate 踢脚板kicker shim 切槽垫片kiloohm 千欧姆kilowatt 千瓦特kilowatt-hour 千瓦小时kine 凯恩kinetic energy 动能kink 纽接knife edge switch 闸刀开关knob handle 球形手柄"KVA,Kva" 千伏安label 标签,标牌labeling 加标签,贴标签laboratory report 试验报告labour department inspection 劳动部门检查(验收)lacquer coat 漆层lacquer enamel 搪瓷漆ladder 梯子ladder diagram 梯形图lading door dill 厅门地坎lading door safety switch 层门安全开关laminated 层压的,叠压的laminated glass 多层玻璃laminated p;astic panel 层压塑料板,多层塑料板laminated plastic 层压塑料板laminated spring 叠簧laminated wood 多层板lamination 铁芯叠片lamp 灯lamp holder 灯座lamp socket 灯座landic panel 停电自动平装置landing 层站landing apron 厅门护脚板landing button 停站按钮landing call 层站呼梯landing call adder unit 层站呼梯信号加法网络装置landing call button 层站呼梯按钮landing call protection 层站呼梯信号保护landing device 停站装置landing direction indicator 层门方向指示灯landing door 层门,厅门landing door jamb 层门门套landing door locking device 厅门门锁装置landing entrance 层站入口landing indicatior of maching room 机房层站指示器landing indicator 层门指示灯landing interlock 厅门联锁landing plate 门厅板landing position indicator 层站位置指示器landing sagety edge 层门安全开关landing sills 层门地坎landing stop 层站停车landing switch 层站开关landing wiring harness 厅门接线束landing zone 层站区lang lay 同向捻股langding accuracy 停站精度,平层精度lantern 信号灯lap 研磨lap joint 搭接larallel single bank arrangement 重叠配置large quantity production 大量生产large scale production 大规模生产latch nut 锁紧螺母latching relay 门栓继电器lateral 横向的,水平的lathe 车床lay (绳)捻,编lay of rope (钢丝绳)捻股方法layout 布置,平面图layout drawing 布置图LCD 液晶显示器LCR 最低层呼梯反向LD 逻辑器件,逻辑装置lead 引线,导程,螺距lead 铅lead seal 铅封lead time 供货周期leaf 片,叶,门扇leaf spring 片簧leaflet 散页印刷品leakage 泄漏leakage coefficient 漏磁系数leakage current 泄漏电流leaving passenger 出梯乘客LED 发光二极管ledge 架,支架left hand machine 左手曳引机left hand two speed sliding door 左开门left handed worm 左旋螺杆left lay 左捻(绳股)left opening two speed sliding door 左开双扇门left-hand twist (绳)左向绞legible 易读的length 长度lens 透镜letter of credit 信用证letter of intent 意向书level "场水平,高度"level gear 伞齿轮level transducer 平层传感器leveling 平层leveling accuracy 平层准确度leveling cam 平层碰铁leveling device 平层装置leveling error 平层误差leveling inaccracy 平层误差leveling inductor plate 平层感应板leveling mode 平层模式leveling speed 平层速度,爬行速度leveling switch 平层开关leveling zone 平层区leveling-in zone 平层区lever 手柄,杆lever drive 手柄驱动lever handle 杆式手柄liability to guarantee 担保责任license 许可证license agreement 许可证协议license contract 许可证合同license fee 许可证费用license holder 许可证持有者license plate 使用许可,汽车牌licensee 持有许可证(执照者)lift 电梯lift attendant 电梯司机lift car 轿厢lift controil valve 升降控制阀lift cycle 电梯运行周期lift group control 电梯的群控lift in use indicator 电梯在使用中指示器lift inspector 电梯检查员lift machine 电梯曳引机lift management 电梯管理lift on ships 船用电梯lift series 电梯系列型谱lift tester 电梯测试员lift well 电梯井道lifting cam for sagety shoe (门)安全触板缩回凸轮lifting capacity 提升能力lifting height 提升高度lifting height of lift 电梯提升高度lifting hook 起重吊钩liftwell 电梯井道light beam safety switch 光线安全开关light bulb 灯泡light device of pit inspection 底坑检修照明装置light duty traffic 轻量交通light metal 轻金属light switch 照明开关light traffic 轻闲交通lighting 照明lighting circuit 照明电路lighting current 照明电流lighting fixture 灯具lighting source 照明电源lighting voltage 照明电压lighting window 采光窗户lightweight 重量轻的,轻质的lightweight concrete 轻质混凝土lighyting barrier 照明障碍limit curve 临界曲线limit switch 限位开关limiting circuit 限制电路line diagram 线图表line filter 管道过滤器line motor 直线电机line spacing 行距line voltage 线电压linear circuit 线性电路linear induction motor(LIM) 直线感应电动机linear speed 线速度liner 衬套lining 衬套link 链环,链节link library 程序库linkage 连杆linkage address 联系地址linkage specification 连杆规格表lintel 门楣liquid 液体liquid level 液位liquid level detector 液位检查器liquid level indicator 液位指示器list of materials 材料清单list of parts 零件清单live load 活动负荷living expenses 生活费用L-Key 内六角扳手ln-off signal 通断信号loac curve 载荷曲线load 负载,载量(数据,程序等)装入load cell 称重装置load condition 载重状态load measuring 杆量,称量load measuring choke coil 称量扼流线圈load measuring device 称重装置load measuring sensor 载重传感器load test 载重试验load transducer 载重传感器load weighing 称量load weighing floor 称量轿底load weighing platform 称量轿底load weighting device 称重装置loading 负载,负荷loading internal 乘客间隙时间loading internal timeloading time 进入电梯时间,装载时间loading weight 载重量lobby 楼厅,候梯厅lobby panel 门厅调度盘lobby surveillance 门厅检测装置local code 当地规定local lighting 局部照明local quench 局部淬火local regulation 当地规定local zone 本层楼区lock bolt 锁紧螺栓lock device 锁住装置lock down sagety 向下锁定安全装置lock net 锁母lock out operation 分离运转,分离操作lock striker 门锁碰头lock washer(L/W) 斜垫片lockable 可闭锁的,可锁定的locker 摇杆,锁紧器lock-in circuit 自保电路locking jaw 锁紧爪locking relay 自锁继电器locks 门锁装置,联锁装置log diary 运行日记logger 记录器logic analyser 逻辑分析器logic circuit 逻辑电路logic diagram 逻辑图logic element 逻辑元件logical combination 逻辑结合long ton 长吨,英制吨long wait hall call 候梯时间较长的门厅呼梯long wait landing call 候梯时间较长的层站呼梯longitudinal 纵向的Long's lay rope 同向捻(顺捻)钢丝绳loop 环圈loop circuit 环形电路loop current 环流loose bearing 松配轴承loose fit 动配合loss 损耗loss of power 功率损耗loudness level 响度louver 气窗low carbon steel 低碳钢low cost 低成本的,廉价的low rise building 低层建筑物low speed 低速的,慢速的low speed winding 低速绕组lower chord 下楔材料lower cost solution 低成本方案lower frame 底部框架lower/upper landing (自动扶梯)下部/上部通道lowest call reversal(LCR) 最低层呼梯反向lowest reversal floor 最低反向楼层low-rise lift group 低层区电梯组群low-rise zone 低层区low-speed door 低速门LS(limit switch) bracket 限位开关支架LS(limit switch) cam 限位开关碰铁lubricant 润滑剂lubricating fitting 润滑装置lubricating instructions 润滑说明书lubrication 润滑lubrication ring 润滑油杯lubricator 润滑器lug 线桥luggage lift 行李电梯lumen 流明(光通量单位)luminous indicator 发光指示器Lux 勒克司(照明单位)luxury car 豪华轿厢machinability 切削性machine 曳引机machine beam 曳引机承重钢梁machine beam plate 曳引机支撑板machine bed 曳引机座machine bed inserting mortar 曳引机座(砂浆)灌缝machine bed plate 机器底板,曳引机底板machine driving 曳引机machine earthquake proof stopper 曳引机防震挡止器machine elevation device 曳引机高度调整装置machine frame 曳引机架machine installation 曳引机安装machine isolation 曳引机隔震machine isolation device 曳引机隔震装置machine language 机器语言machine No. plate 曳引机编号牌machine room 机房machine room area 机房面积machine room arrangement 机房布置machine room depth 机房深度machine room height 机房高度machine room inspection 机房检修machine room lower 下机房machine room of hydraulic lift 液压电梯机房machine room plan 机房布置图machine room upper 上机房machine room width 机房宽度machine room wiring harness 机房配线束machine sheave cover 曳引机绳轮罩machine spacing bed 曳引机高度调整底座machine supporing steels 曳引机承重钢楔machine supporting beams 承重梁machine supporting steelwork 曳引机承重钢结构machine tools 机床machined 机加工的machinery 机械machining 机械加工machining allowance 加工余量machining in general 普通机械加工magnet 磁条magnet brake 磁力制动器magnet coil 电磁线圈magnet lamination 电磁铁芯片magnet plunger 插棒式电磁magnet vane 隔磁板magnetic amplifier 磁放大器magnetic brake 电磁制动器magnetic catch 磁闩magnetic charateristic 磁特性magnetic clutch 磁性离合器magnetic detector 磁力检查器magnetic flux 磁通量magnetic flux density 磁通密度magnetic leveling switch 磁性离合开关magnetic noise 电磁噪声magnetic pole 磁极magnetic resistance 磁阻magnetic switch 磁感应开关magnetism 磁性magnetism pole 磁棒magnitude 大小,数量,等级magntic core 磁铁芯mahogany 红木main chain 主链条main circuit 主电路main circuit breaker 主断路器main circuit control 主电路控制main contact 主触点main contactor 主接触器main drive 主驱动装置main drive chain 主驱动链main drive chain guard 主驱动链保护装置main drive shaft 主驱动轴。
abbreviation 缩语abnormal "不正常的,反常的" abnormality monitoring 异常监听abrasion 磨损abrasion resistant 耐磨性abrasive cloth 砂布absorb 吸收absorber 减振器AC drive 交流拖动AC feedback control 交流反馈控制AC motor 交流电机AC servo 交流伺服AC servo motor 交流伺服电机AC single speed 交流单速AC two speed 交流双速AC two speed motor 交流双速电动机AC variale speed 交流调速AC(alternating current) 交流电acanning cycle 扫描周期,扫描循环acceleration control system 加速度控制系统acceleration(accel)rate 加速器accelerator 加速器acceptance of lift 电梯验收acceptance period 验收阶段acceptance test 验收试验acceptanec certificate 验收证书access door 检修门access forbidden 禁止入内access lift 通道电梯access security 通道防卫access switch "通道开关,维修用开关" access way 进出通道accessibility "可通达性,接近的,难易程度" accessible 允许进入accessible space 允许进入的场地accessory "配件,附件"accident 事故accident insurance 事故保险accident prevention 事故预防accidental contact 触电accidental operation 误操作accordion door 折叠门accumulation 累积accumulator 蓄电池AC-GL machine 交流无齿曳引机acoustic "听觉的,声音的"acrew die 板牙activate "启动,触发"active mode 主动模式actual condition "实际状况,实际条件" actual load 实际载荷actual state 实际状况actual value 实际值actuate "开动,操作,激励"actuating linkege 操作连杆actuating magnet 操作磁铁actuation time 动作时间actuator "操纵机构,激励器,螺线管" actuator bracket 调节器支架actuator plate 调节板ACVF drive 交流调频拖动ACVF system 交流调频系统ACVF(AC varible frequency) 交流调速ACVV dirve 交流调压拖动ACVV system 交流调压系统ACVV(AC varible voltage) 交流调压adaptation "适应,匹配"adapter PCB 选通脉冲印刷电路板adapter(adapator) 适配器adapting 选配adaptive control system 自适应能力控制系统addendum "齿顶高,附录"addendum circle 外圆adding working drawing 附加加工图addition "附加物,加法"additional materials 附加材料address 地址adhesion "胶,粘合胶"adhesion protective oil 防粘油adhesive foil 胶粘薄膜adhesive tape 胶带adjacent 邻近的adjacent car "相邻轿厢,相邻电梯" adjacent entrance 相邻出入口adjusment 调试adjustable condensor 可变电容器adjustable resistance 可调电阻adjustable spanner 可调扳手adjustable speed electric drive 调速电力拖动adjustable wrench "活动扳手,可调扳手"adjusting screw 调节螺丝adjustor 调试员administation overjhead rate 管理费用标准administration cost 管理成本administration expenses 管理费用advance door opening 提前开门advance payment 预付款advanced "提前的,先进的"advanced carriage 超前拖板(选层器)advancing position reference value 超前位置参考值aerial cableway "空中缆车,架空索道"aerial ropeway "空中缆车,架空索道"aerial tramway "空中缆车,架空索道"aesthetic 美观after sales service 售后服务agency 代理agenda 议程air cord (门机用)航空钢丝绳air purifier 空气滤清剂air ventilator 通风管air-bleed 空气分泄器airborne noise 空气传播噪声air-condition 空调air-gap 气隙alarm 警报alarm bell 警铃alarm button 警铃按钮alarm buzzer 警报蜂鸣器alarm circuit 警报电路alarm system 警报系统ALC(autoclaved light-weight concrete) 蒸压轻质混凝土alcove arrangement 电梯U型排列法algorithm 算法规则系统align 校正aligning template 校正样板alignment 校正alignment gauge 校正量规alkali 碱all-computer-controlled 计算机全控的allocation "分配,分派"allocation of landing call 层站呼梯指令分配allowance "允用误差,加工余量"allowble stress for temporary load 允许暂时应力值alloy 合金alloy steel 合金钢alteration 改进alternate floor 隔层alumina 氧化铝aluminum 铝aluminum alloy 铝合金aluminum bronze 铝青铜aluminum cladding 铝制包层alumite 防蚀铝alundum 氧化铝ambient 环境的ambient noise 环境噪音ambient temperature 环境温度ammeter 安培计ammonia 氨amperage 电流强度ampere 安培amplification 放大amplification stage 放大等级amplifier 放大器amplifying tube 放大管amplitude 幅度analog adder 模拟加法器analog computer 模拟计算机analog speed card 模拟曲线板analog-digital converter 模拟-数字转换器analogue(analog) 模拟analysis 分析analysis mode 分析模拟anchor bolt 地脚螺栓anchorage "锚具,锚定"angle bar 角钢angle guide 角铁导轨angle iron 角铁angle iron frame 角铁框架angle of contact 接触角angle of deflection 导向角angle of inclination 倾斜角angle of lead 导程角angle of traction 曳引机包角angle of wrap 包角angle steel 角钢angular contact ball bearing 向心推力球轴承angular contact bearing 角面接触滚动轴承angular gear 斜齿轮angular retardationg 角减速度angular velocity 角速度anneal 退火annealing 退火annual inspection 年检annual report 年度报告annunciator "报音器,声音合成器"anode 阳极anodize 氧极氧化ANSI(America Nationa Standard Instirute) 美国国家标准协会anti-clockwise 逆时钟方向anti-corrosive paint 防腐蚀漆anti-creep 防蠕动anti-friction bearing 抗摩擦轴承anti-nuisance 防干扰anti-nuisance device 防捣乱装置anti-phase braking 反向制动anti-phase current 反相电流anti-rebound of compensation rope device 补偿绳防跳装置anti-residual 防剩磁anti-resonance 抗谐振anti-reversion device 防反转装置anti-rust 防锈anti-stall 防空转anti-vibralion pad 防震垫APM(automatic people mover) 自动人员运输机apparen power 视在功率apparent output 视在输出applicant 申请人application 申请application guide 应用指南aprons 裙板arbour "轴,杆"arc chamber 电弧隔离室arc protection 防电弧arc quenching 熄焊弧arc shield 电弧屏蔽arc suppressor 灭焊器architect 设计单位architecture 建筑学architrave 门框area 面积arm "臂,支路"armature 电驱armature coil 电驱线圈armature current 电驱电流armature lamination 电驱铁芯片armature shaft 电驱轴armature spider 星形轮armature winding 电驱绕组armoured 蛇皮管的armoured cable 蛇皮管电缆armoured conduit 导线管arrangement 布置arrival bell 到站铃arrival buzer 到站蜂鸣器arrival floor 到达楼层arrival gong 到站钟arrival rate 到站率article of consumption 消耗品artificial intelligence 人工智能artistic 工艺artistic face 工艺表面asbestos packing 石棉盘根ascending 上升ASIC(application specific integrated circuit) 专用集成电路assemble 装配assembler language 汇编语言assembly of hinge 铰链组装assign 分配astragal 装饰镶条atmospheric influence 大气影响attachment 附件attendant control 有司机控制attendant control compartment 有司机控制盒attendant operation 有司机操作audible signal 音响信号audio tape recording 磁带录音authority "当局,核准部门"authority of lift acceptance 电梯验收部门authorized "授权的,核准的"authorized user 核准使用者auto-adaptation 自适用AutoCAD 自动计算机辅助设计autographic recoder 自动记录仪automatic 自动的automatic allocator 自动分派器automatic by-pass 自动直驶automatic center opening sliding door 自动中分式滑动门automatic closer 自动关闭门automatic dispatch 自动调度automatic door 自动门automatic homing 自动回基层automatic landing 自动停站automatic landing system by spare battery 靠备用蓄电池的自动停站设备automatic leveling 自动平层automatic lubricator 自动润滑装置automatic parking garage 自动停车库automatic parking system 自动停车系统automatic relevelling 自动平层校正automatic rescue device 应急救助装置automatic return 自动返回automatic telescopic center opening sliding door 自动中分式折叠滑动门automatic telescopic sliding door 自动折叠式滑动门automobile lift 汽车电梯autowalk 自动人行道auxiliary apparatus 辅助装置auxiliary brake 辅助制动器auxiliary cicuit 辅助电路auxiliary contact 辅助触点auxiliary drive 辅助驱动auxiliary lock 辅助锁auxiliary materials 辅助量auxiliary value 辅助材料auxiliary winding 辅助绕组available area 有效面积average 平均average car load 平均轿厢负载average dispatching interval 平均调度间隔时间average interval 平均调度间隔时间average passenger waiting time 平均乘客侯梯时间average response time 平均应答时间average waiting quest 平均乘客量average waiting time 平均乘客侯梯时间axial flow fan 轴流式风扇axis 轴线axle 轴babbit 巴氏合金babbit lined bearing 巴氏合金衬里轴承babbit melter 巴氏合金熔化器babbit metal 巴氏合金babbit rope socket 灌注式巴氏合金绳头back current 反向电流back e.m.f 反电动势back lash 轮齿隙back plunger type 后部柱塞式(液压梯) back side "后侧,后边"back type governor 轴流式限速器back wall 后壁baked enamel 烤漆balace weight 平衡器balance 平衡balance chain 平衡链balance coefficient 平衡系数balanced traffic 平衡交通ball bearing 滚珠轴承ball cup 球形碗ball pin 球形硝ball stop valve 球形断流器ball type bearing 滚珠轴承ballast 镇流器balustrade deching 外侧盖板balustrade exterior panelling 外装饰板balustrade lighting 扶手照明balustrade panel 扶手板balustrade skirting 扶手群板balustrades 扶手装置bandsaw 带锯bank "银行,群组,排"bar "条,棒"bar code 条形码bar lock 杆式锁bare wire 裸线barricade "防护墙,隔墙"barrier "隔板,栅栏"base "基座,基础"base plate 基板basement 地下室basement service 底下室服务basement type 底吊式basic logic element 基础逻辑元件basic logic function 基础逻辑功能batch production 批量生产battery- backed 电池支持的battery box 蓄电池箱battery charger 电池充电器baud rate 波特率BCD(binary coded decimal) 二进制编码的十进制beam 梁beam pad 井道内电缆保护垫片beam pulley 抗绳轮bearing 轴承bearing bracket 轴承支架bearing cap 轴承盖bearing load 轴承负荷bearing plate 承重板bearing play 轴承间隙bearing sleeve 轴承衬套bearing stand 轴承座bed lift 病床电梯bed plate 底座bell 铃belt 胶带belt drive 胶带传动belt grinder 胶带磨床belt pulley 胶带轮belt type moving walk 带式自动人行道bending 弯曲bending stress 弯曲应力benzine 轻汽油bevel gear 伞(斜)齿轮beveled washer 斜垫圈BGM (background music) 背景音乐BGM speaker 背景音乐扬声器bias "偏置,偏移"bid "投标,报价"bid table 报价单bidder 投标bidding cycle 投标有效期限bidding procedure 投标(报价)程序bil of delivery 发货单bil of lading 海运提单bill of expenses 费用帐单bill of materials 材料单billing 开发票binary 二进制bi-parting 对开式(上下开启)bi-parting door 垂直中分门bipartite light transistor 双分式光电管bistable magnetic swich 双稳态磁开关bistable switch 双稳态磁开关bitumen 沥青blade "叶片,刀片,锯片"blade connector 刀形连接器bleed-off circuit 泄放电路blind hoistway 盲(无门)井道block chart 方框图block diagram 方框图线路block of flats 住宅楼区blocking of control circuit 控制电路闭锁blower 鼓风机blower coil 吹弧线圈blower motor 风机电动机blue print 蓝图boading floor 登梯楼层boading time 登梯时间boarding 登梯boarding landing 登梯层站boarding passenger 登梯乘客boarding rate 登梯率boarding stop 登梯停站boarding zone 登梯区域bobbing 绕线管boldface type 粗字体bolt 螺杆booster 升压机border condition 边界条件bore hole "钻孔,镗孔"boring 镗boring lathe 镗床boring machine 镗床boring miller 镗铣床bottom 底部bottom car clearance 轿底安全高度间隙bottom car overtravel 底部轿厢越程bottom car runby 底部轿厢越程bottom clearances for car 轿底间隙bottom counterweight clearance 轿底对重间隙bottom counterweight overtravel 轿底对重越程bottom counterweight runby 轿底对重越程bottom door retainer 门下角bottom floor 底部楼层bottom runby 底部越程bottom slow down switch 底部减速开关bottom stop 底部停战bottom terminal floor 底部楼层bottom terminal landing 底部端站bottom terminal stop 底端停站box "盒,箱"box counterweight 箱式对重Braille 盲文字符brake 制动器brake arm 制动器臂brake contact 制动器触点brake coutact 制动器联轴器brake dish 制动盘brake drum 制动轮brake energy 制动力brake level 制动器杠杆brake lever 制动器手柄brake lining 制动器衬套brake linkage 制动器连杆brake operater switch 制动操纵开关brake pin 制动器悄brake press "折弯机,压弯机"brake pulley 制动轮brake release lever 制动器松闸手柄brake release magnet 制动器送闸磁铁brake release time 制动器松闸时间brake shoe 制动靴brake spacing 制动器间距brake spring 制动弹簧brake tension 制动器张紧力brake torque 制动器力矩brake wrench 制动器板手braking 制动braking distance 制动距离braking force 制动力branch circuit 分支电路brass founder 铸铜break "切断,破断"break-down 故障breaking load 破断负荷breaking strength 破断强度breaking test 破坏实验breather 通气管brick 砖brick-layer 砖砌工bridge circuit 桥式电路bridge connector 桥接器bridge jumper 桥接片bridge rectifier 桥式整流器bright controlling 光度控制broach 拉力broaching machine 拉床brochure 手册broken chain contact 断链触点broken circuit 断路broken drive chain contact 主驱动链保护装置broken drive-chain safety device 驱动链条保护装置broken rope contact 驱动链条列断安全装置broken step chain contact 断绳触点broken step chain device 断绳开关broken step chain safety device 梯级链断列触点broken step safety device 梯级破列安全装置broken tape sweitch 短带开关bronze 铜brunching "成组,成群"brush finished stainless steel 哑光不锈钢brush holder "刷握,滑环"brush yoke 刷架budget 预算buffer 缓冲器buffer base 缓冲器底座buffer plate 缓冲器板buffer plunger 缓冲器柱塞buffer return spring 缓冲器复位弹簧buffer stand 缓冲器台buffer striking plate 缓冲器撞板buffer stroke 缓冲器冲程buffer support 缓冲器支承buffer switch 缓冲器开关buider's work drawing 土建图纸buiding facility 大楼设施buiding supervision center 大楼监管中心builder 建筑单位building 建筑building area 建筑面积building contractor 建筑承包商building manager 大楼管理者building monitoring and security system 大楼监管和安全系统building population 大楼居住人口built=in 内装built-in escalator 组合式自动扶梯bumper 弹簧式缓冲器bumper rail 防撞板bumpy ride 颠簸振动的运行buried 埋入的burn in (程序)灌入burr "毛刺,毛边"burr free 去毛刺bus 总线bus bar 汇流条bush 衬套bushed bearing 加衬轴套bushing "衬套,轴套,套筒"butt joint "平接,对焊"button 按钮button switch 按钮开关buyer 买方buzzer 蜂鸣器buzzer switch 蜂鸣器开关bypass 直驶by-pass button 直驶按钮by-pass valve 溢流阀bypassed floor 直驶不停楼层bypassed stop 直驶不停层站C$F 到岸价cab "轿厢,座舱"cab interior 轿厢内部cabin "轿厢,座舱"cabinet "柜,厢"cable 电缆cable box 电缆箱cable car 缆车cable cleat 电缆夹具cable conductor 电缆导线cable entry 电缆引入cable hanger 电缆吊架cable hole 电缆孔cable joint 电缆接头cable termination 电缆末端cable trunk 电缆接头CAD 计算机辅助设计cage 轿厢cage door 轿厢门calculation 计算机辅助设计calibrate 校准call "呼梯,呼叫"call acceptance 呼梯接收call accepted 接受呼梯call accepted indicator 接受呼梯指示灯call accepted signal 接受呼梯信号call allocation 呼梯分派call assignment 呼梯指令分配call band 呼梯信号带call button 呼梯按钮call cancel 呼梯取消call canceling 呼梯取消call coincidence 呼梯重合call conmting system 呼梯计数系统call contrl 呼梯指令控制call emitter 呼梯指令发送器call input 呼梯输入call input capacity 呼梯输入内容call input device 呼梯输入装置call load 呼梯输入call memory 呼梯记忆call registered 登陆的呼梯call registered signal 登陆的呼梯信号call registration indicator 呼梯登陆信号call sequence 呼梯顺序call tegistration 呼梯登陆call-back 召修call-back message 召修信息callinfg board 召唤盒calling floor 呼体楼层calling landing 呼梯call-out response time 维修召唤应答时间call-out service 急修服务CAM 计算机辅助制造cam 凸轮cam for positive operation 强制操纵凸轮cam lever 偏心柄cam shaft 偏心轴cam tape control 偏心带控制cam-gear 凸轮传动装置cam-operated switch 凸轮(碰铁)操纵开关cancel "撤消,取消"cancelingof call signal 呼梯信号消除cancellation "撤消,取消"canopy "顶盖,大蓬"canvas 帆布canvas hose 帆布软管cap "帽,盖子"cap nut 螺母capacitance "电容,电容量"capacitor 电容capacitor motor 电容器电机capacity "载重,容量,定员"capacity plate 载量标牌capstan 绞盘captive roller safety gear 滚柱式安全钳car 轿厢car annunciator 轿厢报警器car approaching gong 轿厢到站预报钟car apron 轿厢入口群板car assignment "轿厢调度,轿厢分配"car automatic switch landing 轿厢开关自动停站car axis 轿厢中心线car back wall 轿厢后壁car botom clearance 轿厢安全高度car bottom overtravel 轿厢底部越层car bottom runby 底部越程car buffer 轿厢缓冲器car button 轿厢按钮car cab 轿厢体car call 轿厢指令car call button 轿厢指令按钮car call cancel 轿内召唤取消car call control 轿厢指令控制car call panel 轿厢(呼梯)指示盘car call stop 轿厢(呼梯)指令停车car cam 碰铁car canopy 轿厢顶盖car ceiling 轿厢装饰顶car coming indicator 轿厢驶近指示灯car control lever 轿厢操纵手柄car control switch 轿厢操纵开关car counterweight 轿厢对重car cross-head 轿厢上梁car depth 轿厢深度car dispatch 轿厢调度car door 轿门car door catch 轿门栓car door closer 轿门关闭器car door electric contact 轿门电触点car door guide shoe 轿门导靴car door interlock 轿门联锁car door lock 轿门门锁car door rail 轿门导轨car door sill 轿门地坎car door track 轿门导轨car elevator 汽车电梯car emergency exit "轿厢安全门,应急门"car emergency opening 轿厢安全窗car emergency release switch 轿厢应急释放按钮car enclosure panel 轿厢壁板car enclosures 轿厢壁板car entrance 轿厢入口car extetior "轿厢外装修,轿厢外表"car fan 轿厢风扇car floating movable platform 轿厢活动地板car floor frame "轿厢架,轿架"car frame "轿厢架,轿架"car frame attachment 轿厢框架附件car frame plank 轿厢下梁car frame upright 轿厢立柱car front 轿厢前壁car full control 满载轿厢控制car gate 轿厢门car gate contact 轿门触点car gate electric contact 轿门电气触点car guide 轿厢导轨car guide axis 轿厢导轨中心线car handle control "手柄开关操纵,轿内开关控制" car handrail 轿厢扶手car height 轿厢高度car illumination 轿厢照明car isolation 轿厢隔震器car leveling device 轿厢平层装置car lift 汽车电梯car light 轿厢照明装置car light panel "轿厢照明板,照明天花板"car lighting 轿厢照明car manual switch landing 轿厢手动开关停站car operation board 轿厢操纵盘car operation panel 操纵箱car overload 轿厢超载car panel 轿厢壁板car panel attachment 轿厢壁板附件car panel base 轿厢壁板底座car panel with window 轿厢壁板上窗口car platform "轿厢底,轿底"car platform guard 轿厢站台护板car platform sill 轿厢car position indicator "轿厢指示灯,轿厢位置显示"car position reference value 轿厢位置参考值car preference 轿厢优先权car push-button 轿厢按钮car rear wall 轿厢后壁car roof "轿厢顶,轿顶"car safety 轿厢安全钳car safety bar for dumbwaiter 轿厢安全棒(杂货梯)car safety gear 轿厢安全钳car safety mechanism switch 轿厢安全钳联动开关car sheave 轿厢绳轮car side emergency door 轿厢安全侧门car side opening 轿厢侧面开门car side wall 轿厢侧壁car sill 轿厢地坎car sling "轿厢架,吊架"car station 轿厢操纵站car status information 轿厢运行状态信息car stop 轿厢停止car suspension 轿厢悬挂装置car switch 轿厢开关car switch automatic floor stop operation 轿厢开关自动停站装置car switch control 轿厢开关控制car switch opration "手柄开关操纵,轿内开关控制"car top 轿厢顶部car top clearance 轿顶安全高度car top emergency exit "轿顶安全出口,轿顶应急出口"car top guard 轿顶护栏car top inspection device 轿顶检修装置car top inspection station 轿顶检修盒(站)car top light 轿顶照明装置car top protection balustrade 轿顶防护栏杆car top protection railing 轿顶防护栏杆car ventilation 轿厢通风car walls "轿厢壁,轿壁"car weight 轿厢重量car width 轿厢宽度carbon "碳,石墨"carbon brush 碳刷carbon contact 碳精触点carbon steel 碳素钢carburization 渗碳carburize 渗碳carburized hardening 渗碳硬化carburizer 渗碳剂card "卡片,纹板"card reader 卡片读出器cardan joint 万向接头carpet 地毯carriage charges 运费carry frequency "载波频率,开关工作频率" carrying capacity "载运量,载运能力"cart elevator 车辆运货电梯cartridge fuse 插塞式熔断器carving machine 刻模机cascade "级联,串联"cascade sub-loop 串接式子回路case "箱,盒,外壳"casing "保护套,外套"casing of cylinder 油缸套cassette tape 录音带cast bronze 铸青铜cast iron 铸铁cast steel 铸钢casting 铸造castor oil 蓖麻油catch "擎子,门扣,捕捉器"catch block 安全钳catch clip 捕捉夹钳catch device 捕捉装置cathode 阴极cathode ray tube(CRT) 阴极射线管cavitation "气穴,涡穴,饱和压力点" ceiling 吊顶ceiling assembling 轿顶cellulose 纤维板cement "水泥,胶合剂"cement concrete 混凝土cenrifugal brake 离心制动器center 中心center latch 中心门栓center line 中心线center of curvature 曲率中心center opening 中分式门center opening door 中分门center opening two speed door 中分四扇门center opening vertical sliding door 中分式垂直滑动门center plunger hydraulic lift 柱塞直顶式液压电梯center support "中心支撑,中间支撑,第三支撑" center-opening folding door 中分式折叠门centigrade 摄氏温度central alarm 中央报警central control board 中央监控盘central control room 中央监控室central jack 中心液压装置central position 中心位置centrifugal 离心的centrifugal cast 离心铸造centrifugal fan 离心式风扇centrifugal governor 离心式限速器centrifugal speed 离心速度centrifugal switch 离心开关centrifugal type governor 离心式限速器centripetal force 向心力ceramic capacitor 搪瓷电容certification 证书certifying body 认证机关chain 链条chain block 手拉葫芦chain bracket 链条托架chain drive 链传动chain drive elevator 链驱动升降机chain drive machine 链驱动机chain gear 链轮chain guard 链防护罩chain link "链节,链环"chain pitch 链条节距chain sag 链条下垂度chain sheave 链轮chain sprocket 链轮chain sustarned elevator 链支撑升降机chain tensioning device 链张紧装置chain wheel 链轮chain wheel track 链轮导轨chamger "倒棱,去毛刺"change switch 转换开关change-over contact 转化触点change-over landing 换乘电梯层站change-over switch 转换开关change-pole 变化极性channel 槽钢channel iron 槽铁channel steel 槽钢character "特征,字符" characteristic "特征,特性" characteristic curve 特性曲线charge "充电,收费"charged "带电,充电"charging contactor 充电接触器charging set 充电chart 图表chart of accounts 成本图表check valve 止逆阀chequer(checker)plate 网纹钢板chief engineer 总工程师chime 音钟chip 芯片chipboard 木屑板chisel 凿子choke "扼流,截流,阻塞"choke coil 扼流线圈chopper 斩波器chrome 铬chuck 卡盘CIF(cost insurance and freight) 到岸价cinder concrete 煤渣混凝土circle "周期,圆"circuit 电路circuit breaker "断电器,断路器" circuit diagram 电路图circular pitch 周节circulating pump 循环泵circulation 循环circumferential force 圆周力circumferential speed 圆周速度circumferential velocity 圆周速度CL(center line) 中心线clacking 盖板cladding 装饰clamp 夹clamp ring "压制环,加紧环"clamping jaw 夹钳clamping sleeve 夹紧套桶clamping strap 制动带class of loading 灾荷种类clear depth 净深度clear dimension 净尺寸clear door height 门净高度clear door width 门净宽度clear entrance to the car 轿厢入口净尺寸clear height 净高clear hoistway 井道净尺寸clear width 净宽度clearance between skirt panels 裙板间隙clearance bottom car 轿底安全高度clearance top car 轿顶安全高度clearance top counterweight 对重装置顶部安全高度cleated riser 梯级竖板clerance 间隙clevis U型夹client "客户,买主"clip 钳夹clockwise 顺时针的close circuit 闭合电路closed loop 闭环closed position (门)关闭位置closed position monitoring (门)关闭位置检测closed-loop control 闭环控制closed-type motor 闭合式电动机closer 关门器closing force (门)关闭力closing speed 门关闭速度closing travel 门关闭运行closing valve 切断阀clutch 离合器clutch component 离合器部件clutch plate 离合器板clutch release sleeve 离合器释放套管clutch spring 离合器弹簧CMOS 互补型金属氧化物(半导体)CNC(computerized numric control) 计算机数控coast to stop 滑行停车coating 涂层coaxial cable 同轴电缆cock 龙头code "码,符号,规程,规范"code of practice "实施规程,实用规程"code word 代号文字coding PCB(printer cicuit board) 编码印刷电路板coefficient 系数coefficient of friction 摩擦系数coil "线圈,绕组"coil case 线圈外壳coiled spring 螺旋弹簧coincidence memory 重合记忆coinciding call 重合呼梯指令cold cathode 冷阴极collapsible door 栅栏门collapsible gate "栅栏门,折叠式门"collapsible type door 折叠式门collar 环collecting brush 集电刷collecting ring 轴环collection "收集,集合"collective control 集中控制collective full automatic operation 全自动集中控制collective operation elevator 集中操作电梯collective selective 集选collective selective control 集选控制collector 集电路collision switch 碰撞开关color 颜色colored starnless steel 彩色不锈钢colorfast 不褪色的colorless 无色的column "柱,立柱"comb contact 梳齿板安全装置comb floor plate 梳齿板comb light 梳齿灯comb lighting 梳齿板照明comb plate 梳齿板comb plate contact 梳齿板触板comb plate safety device 梳齿板安全装置commutation 整流commutator 换向环commutator brush 整流子电刷commutator lug 整流片commutator metallic segment 金属整流器compact 紧凑的comparator 比较器compartment "隔板,隔室"compennsating device for hoist ropes 曳引绳补偿装置compensanting/equalizer disk 补偿/补偿器compensating 补偿compensating chain device 补偿链装置compensating condensor 补偿电容器compensating devece 补偿装置compensating rope 补偿绳compensating rope device 补偿绳装置compensating rope hitch 补偿绳绳头板compensating rope sheave 补偿绳轮compensating rope socket 补偿绳绳头compensating winding 补偿绳绕组compensating-rope sheave safety switch 补偿绳轮安全开关compensating-rope sheave switch 补偿绳轮开关compensation chain 补偿链compensation coil 补偿绳线圈compensation rope 补偿绳compensation sheave 补偿绳轮competent "有资格的,胜任的"competent personnel "有资格的人员,胜任的人员"competitor system 竞争机制component 部件compound wind motor 复励电动机compound wound 复绕comprehensive 综合的comprehensive maintenance contract "综合维修合同,全包维修合同" comprehensive service contract "综合维修合同,全包维修合同" compressing spring 压缩弹簧compression 压缩compression switch 压缩开关compressive stress 压应力compressor 压缩器compulogic system 电脑程序控制系统computer 计算机computer peripheral devices 计算机外围装置computer simulation 计算机模拟computing power 运算容量concealed "隐蔽的,暗式"concealed hinge 暗式链条concentrated load 集中载荷concentricity 同心性conclusion of contract 合同成交concrete 混凝土concrete hoistway 混凝土井道concrete machine block 混凝土机座concrete wall 混凝土墙condenser 电容器condenser for power factor improvement 功率因素补偿电容condition 条件condition of payment 付款条件conditions of contract 合同条件conducting wire 导线conductive 导电的conductor 导体conduit 导线管conduit fitting 导线管接头cone roller bearing 滚锥轴承conference room 会议室conical brake 锥形制动器conical pin 锥销conicity 锥度connect in series 串接connecting piece 连接件connecting rod "连杆,连接杆"connection 连接connection diagram of controller 控制柜连线图connector "接线柱,连接器"conract specification "合同规定,合同明细表"conract speed "合同速度,额定速度"consecutively departing 依次派出的轿厢console panel "控制柜,控制盘"constant "恒定的,常数"constant HP motor 功率恒定型电机constant speed valve "比例控制阀,调速阀"constant torque motor 力矩恒定型电机construction "安装,施工"construction crane 建筑起重机construction layout drawing 土建图construction platform "安装平台,施工平台" construction site "安装工地,施工工地" consultant "顾问,咨询机构"consumption 消耗contact 触点contact angle 接触角contact brace 触头撑条contact burning 触头烧损contact carrier 触头支架contact control 有触点控制contact control system 有触点控制系统contact finger "接触指,滑触头"contact forcibly actuated 强迫操动触头contact holder 触头固定架contact input 接触输入端contact load 保证(额定)载荷contact mat 触头垫片contact normally closed 常闭触点contact normally open 常开触点contact pressure 触头压力contact resistance 接触电阻contactless 无触点contactless control 无触点控制contactless control system 无触点控制系统contactless switch 无触点开关contactor 接触器contents 内容conter 计数器continuing travel indicator (轿内)继续运行指示器continuous line arrangement 连锁配置continuous speed regulation 连续速度控制continuous-pressure button 继压开关contract "合同,契约,承包合同"contract capacity "合同载重量,合同容量" contract load 合同负载contract of indemnity 赔偿合同contract party "合同方,合同当事人"contract work system 合同制度control 控制control amplifier 调节放大器control bus 控制总线control cabinet 控制柜control cable 控制电缆control circuit 控制电路control device for handrail brekage 扶手带断带保护装置control feature 控制特征control gear 控制论control guard for handrail breakage 扶手带断带保护装置control lever 控制杆control panel 控制屏control stand 控制台control station 控制站control switgh 控制开关control system 控制系统control system for elevator 电梯控制系统control technique 控制技术control type 控制形式control valve 控制阀control valve unit (液压)调节阀装置control voltage "控制电压,操作电压"controlled angle 控制角controller 控制柜controller base 控制柜底座controller cabinet 控制柜controller panel 控制屏controller wiring diagram 控制柜电路图controlling circuit 控制电路conuter-clockwise 逆时针方向conventional 常规的conventional lift 普通电梯converter "整流器,转换头"converter panel 换流器盘converter set 换流器组件converter unit 换流装置conveyance of passengers 乘客载运conveyer 输送机conveyer track 输送车轨道cooler 冷却装置cooler air-conditioner 空调制冷cooling 冷却cooling device for semiconductor 半导体冷却装置cooling fan 冷却风扇COP(car operation panel) 轿厢操纵盘copper 铜cord "绳索,芯线"cord drive "绳传动,(厅门)"core 铁心core press 铁心压力。