Invision 450 MPa 操作简介操作步骤：
每次选择按一下此键“SETUP”，需要调整选择“ADJUST”.步骤1 Arc Control 步骤4 Gas
步骤2 Process 步骤5 P rogram Load
步骤3 Wire
P
MIG-普通气保护焊/ 焊丝选择表
焊丝类型保护气类型
钢035 (0.9mm) STL
045 (1.2mm) STL
052 (1.4mm) STL
ARGN CO2 (80%氩气+20%二氧化碳)
ARGN OXY (95%氩气+5%氧气)
1/16 (1.6mm) STL ARGN CO2 (80%氩气+20%二氧化碳) .035 (0.9mm) STL
.045 (1.2mm) STL
CO2 (100%二氧化碳)
金属粉芯焊丝.045 (1.2mm) MCOR
.052 (1.4mm) MCOR
1/16 (1.6mm) MCOR
ARGN CO2 (80%氩气+20%二氧化碳)
药芯焊丝.035 (0.9mm) FCAW
.045 (1.2mm) FCAW
.052 (1.4mm) FCAW
1/16 (1.6mm) FCAW
ARGN CO2 (75%氩气+25%二氧化碳) *
CO2 (100%二氧化碳)
不锈钢.035 (0.9mm) SSTL
.045 (1.2mm) SSTL
TRI MIX (81%氩气+18%氦气+1%二氧
化碳)
ARGN OXY (95%氩气+5%氧气)
普通MIG（0-100）脉冲PULS（0-50）
MIG（普通气保焊）PULS（脉冲气保焊）
焊丝直径（左边）
焊丝材质（右边）保护气体选择
焊接工艺选择保存完成
铝.035 (0.9mm) AL4X (4000 Series)
.040 (1.0mm) AL4X (4000 Series)
3/64 (1.2mm) AL4X (4000 Series)
1/16 (1.6mm) AL4X (4000 Series)
.035 (0.9mm) AL5X (5000 Series)
.040 (1.0mm) AL5X (5000 Series)
3/64 (1.2mm) AL5X (5000 Series)
1/16 (1.6mm) AL5X (5000 Series)
ARGN (100%氩气)
对于自保护药芯焊丝，采用ARGN CO2保护气，电感设置小于10 焊丝直径为英寸或mm
PULS -脉冲气保护焊/ 焊丝选择表
钢.035 (0.9mm) STL
.045 (1.2mm) STL
.052 (1.4mm) STL
1/16 (1.6mm) STL
ARGN CO2 (90%氩气+10%二氧化碳)
ARGN OXY (95%氩气+5%氧气)
金属粉芯焊丝.045 (1.2mm) MCOR
.052 (1.4mm) MCOR
1/16 (1.6mm) MCOR
ARGN CO2 (90%氩气+10%二氧化碳)
不锈钢.035 (0.9mm) SSTL
.045 (1.2mm) SSTL
TRI MIX (81%氩气+18%氦气+1%二氧
化碳)
ARGN OXY (98%氩气+2%氧气)
ARGN CO2 (98%氩气+2%二氧化碳) 1/16 (1.6) SSTL ARGN CO2 (98%氩气+2%二氧化碳)
铝.035 (0.9mm) AL4X (4000 Series)
.040 (1.0mm) AL4X (4000 Series)
3/64 (1.2mm) AL4X (4000 Series)
1/16 (1.6mm) AL4X (4000 Series)
ARGN (100%氩气)
.035 (0.9mm) AL49 (4943)
.040 (1.0mm) AL49 (4943)
3/64 (1.2mm) AL49 (4943)
1/16 (1.6) AL49 (4943)
.035 (0.9mm) AL5X (5000 Series)
.040 (1.0mm) AL5X (5000 Series)
3/64 (1.2mm) AL5X (5000 Series)
1/16 (1.6mm) AL5X (5000 Series)
ARGN (100%氩气)
HE AR25 (75%氦气+25%氩气)
镍.035 (0.9mm) NI
.045 (1.2mm) NI
ARGN HE (75%氩气+25%氦气)
ARGN (100%氩气)
1/16 (1.6mm) NI ARGN (100%氩气)
铜镍合金.035 (0.9mm) CUNI
.045 (1.2mm) CUNI
HE ARGN (75%氦气+25%氩气)
硅青铜.035 (0.9mm) SIBR
.045 (1.2mm) SIBR
ARGN (100%氩气)
焊丝直径为英寸或mm
