机械行业专业术语

机械设计类行业专用术语中英对照阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower摆动导杆机构oscillating guide-bar mechanism摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter 齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism 串级调速cascade speed control创新innovation creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing 单万向联轴节single universal joint单位矢量unit vector当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction等加等减速运动规律parabolic motion; constant acceleration and deceleration motion 等速运动规律uniform motion; constant velocity motion等效动力学模型dynamically equivalent model等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心移动从动件radial reciprocating follower对心直动从动件radial (or in-line ) translating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism 多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分度圆reference circle; standard (cutting) pitch circle 分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design 机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交*带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing 角接触向心轴承angular contact radial bearing 角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle分析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism 力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket；sprocket-wheel；sprocket gear；chain wheel 联组V 带tight-up V belt联轴器coupling shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design; design for environment马耳他机构Geneva wheel Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product’s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价和决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing 球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator燃点spontaneous ignition热平衡heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy’s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference 设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift实际廓线cam profile十字滑块联轴器double slider coupling; Oldham’s coupling 矢量vector输出功output work输出构件output link输出机构output mechanism输出力矩output torque输出轴output shaft输入构件input link数学模型mathematic model实际啮合线actual line of action双滑块机构double-slider mechanism, ellipsograph双曲柄机构double crank mechanism双曲面齿轮hyperboloid gear双头螺柱studs双万向联轴节constant-velocity (or double) universal joint双摇杆机构double rocker mechanism双转块机构Oldham coupling双列轴承double row bearing双向推力轴承double-direction thrust bearing 松边slack-side 顺时针clockwise瞬心instantaneous center死点dead point四杆机构four-bar linkage速度velocity速度不均匀( 波动) 系数coefficient of speed fluctuation速度波动speed fluctuation速度曲线velocity diagram速度瞬心instantaneous center of velocity塔轮step pulley踏板pedal台钳、虎钳vice太阳轮sun gear弹性滑动elasticity sliding motion弹性联轴器elastic coupling flexible coupling弹性套柱销联轴器rubber-cushioned sleeve bearing coupling 套筒sleeve梯形螺纹acme thread form特殊运动链special kinematic chain特性characteristics替代机构equivalent mechanism调节modulation, regulation调心滚子轴承self-aligning roller bearing调心球轴承self-aligning ball bearing调心轴承self-aligning bearing调速speed governing调速电动机adjustable speed motors调速系统speed control system调压调速variable voltage control调速器regulator, governor铁磁流体密封ferrofluid seal停车阶段stopping phase停歇dwell同步带synchronous belt同步带传动synchronous belt drive凸的，凸面体convex凸轮cam凸轮倒置机构inverse cam mechanism凸轮机构cam , cam mechanism凸轮廓线cam profile凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve凸缘联轴器flange coupling 图册、图谱atlas图解法graphical method推程rise推力球轴承thrust ball bearing推力轴承thrust bearing退刀槽tool withdrawal groove退火anneal陀螺仪gyroscopeV 带V belt外力external force外圈outer ring外形尺寸boundary dimension万向联轴器Hooks coupling universal coupling外齿轮external gear弯曲应力beading stress弯矩bending moment腕部wrist往复移动reciprocating motion往复式密封reciprocating seal网上设计on-net design, OND微动螺旋机构differential screw mechanism位移displacement位移曲线displacement diagram位姿pose , position and orientation稳定运转阶段steady motion period稳健设计robust design蜗杆worm蜗杆传动机构worm gearing蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear蜗杆形凸轮步进机构worm cam interval mechanism 蜗杆旋向hands of worm蜗轮worm gear涡圈形盘簧power spring无级变速装置stepless speed changes devices无穷大infinite系杆crank arm, planet carrier现场平衡field balancing向心轴承radial bearing向心力centrifugal force 相对速度relative velocity 相对运动relative motion相对间隙relative gap象限quadrant 橡皮泥plasticine细牙螺纹fine threads销pin消耗consumption小齿轮pinion小径minor diameter橡胶弹簧balata spring修正梯形加速度运动规律modified trapezoidal acceleration motion 修正正弦加速度运动规律modified sine acceleration motion斜齿圆柱齿轮helical gear斜键、钩头楔键taper key泄漏leakage谐波齿轮harmonic gear谐波传动harmonic driving谐波发生器harmonic generator斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio行星齿轮装置planetary transmission行星轮planet gear行星轮变速装置planetary speed changing devices行星轮系planetary gear train形封闭凸轮机构positive-drive (or form-closed) cam mechanism虚拟现实virtual reality虚拟现实技术virtual reality technology, VRT虚拟现实设计virtual reality design, VRD虚约束redundant (or passive) constraint许用不平衡量allowable amount of unbalance许用压力角allowable pressure angle许用应力allowable stress; permissible stress悬臂结构cantilever structure悬臂梁cantilever beam循环功率流circulating power load旋转力矩running torque旋转式密封rotating seal旋转运动rotary motion选型type selection压力pressure 压力中心center of pressure压缩机compressor压应力compressive stress压力角pressure angle牙嵌式联轴器jaw (teeth) positive-contact coupling雅可比矩阵Jacobi matrix摇杆rocker液力传动hydrodynamic drive液力耦合器hydraulic couplers液体弹簧liquid spring 液压无级变速hydraulic stepless speed changes 液压机构hydraulic mechanism一般化运动链generalized kinematic chain移动从动件reciprocating follower移动副prismatic pair, sliding pair移动关节prismatic joint移动凸轮wedge cam盈亏功increment or decrement work应力幅stress amplitude应力集中stress concentration应力集中系数factor of stress concentration应力图stress diagram应力—应变图stress-strain diagram优化设计optimal design油杯oil bottle油壶oil can油沟密封oily ditch seal有害阻力useless resistance有益阻力useful resistance有效拉力effective tension有效圆周力effective circle force有害阻力detrimental resistance余弦加速度运动cosine acceleration (or simple harmonic) motion预紧力preload原动机primer mover圆带round belt圆带传动round belt drive圆弧齿厚circular thickness圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover原始机构original mechanism圆形齿轮circular gear圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair圆柱式凸轮步进运动机构barrel (cylindric) cam圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧cylindroid helical-coil compression spring 圆柱凸轮cylindrical cam圆柱蜗杆cylindrical worm圆柱坐标操作器cylindrical coordinate manipulator圆锥螺旋扭转弹簧conoid helical-coil compression spring圆锥滚子tapered roller圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears圆锥角cone angle原动件driving link约束constraint约束条件constraint condition约束反力constraining force跃度jerk跃度曲线jerk diagram运动倒置kinematic inversion运动方案设计kinematic precept design运动分析kinematic analysis运动副kinematic pair运动构件moving link运动简图kinematic sketch运动链kinematic chain运动失真undercutting运动设计kinematic design运动周期cycle of motion运动综合kinematic synthesis运转不均匀系数coefficient of velocity fluctuation运动粘度kenematic viscosity载荷load载荷—变形曲线load—deformation curve载荷—变形图load—deformation diagram窄V 带narrow V belt毡圈密封felt ring seal展成法generating张紧力tension张紧轮tension pulley振动vibration振动力矩shaking couple振动频率frequency of vibration振幅amplitude of vibration正切机构tangent mechanism正向运动学direct (forward) kinematics正弦机构sine generator, scotch yoke织布机loom正应力、法向应力normal stress制动器brake直齿圆柱齿轮spur gear直齿锥齿轮straight bevel gear直角三角形right triangle直角坐标操作器Cartesian coordinate manipulator 直径系数diametral quotient直径系列diameter series直廓环面蜗杆hindley worm直线运动linear motion直轴straight shaft质量mass质心center of mass执行构件executive link; working link质径积mass-radius product智能化设计intelligent design, ID中间平面mid-plane中心距center distance中心距变动center distance change中心轮central gear中径mean diameter终止啮合点final contact, end of contact周节pitch周期性速度波动periodic speed fluctuation周转轮系epicyclic gear train肘形机构toggle mechanism轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承高度bearing height轴承宽度bearing width轴承内径bearing bore diameter轴承寿命bearing life轴承套圈bearing ring轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile轴向当量动载荷dynamic equivalent axial load轴向当量静载荷static equivalent axial load轴向基本额定动载荷basic dynamic axial load rating轴向基本额定静载荷basic static axial load rating轴向接触轴承axial contact bearing轴向平面axial plane轴向游隙axial internal clearance轴向载荷axial load轴向载荷系数axial load factor轴向分力axial thrust load主动件driving link 主动齿轮driving gear主动带轮driving pulley转动导杆机构whitworth mechanism转动副revolute (turning) pair转速swiveling speed rotating speed转动关节revolute joint转轴revolving shaft转子rotor转子平衡balance of rotor装配条件assembly condition锥齿轮bevel gear锥顶common apex of cone锥距cone distance锥轮bevel pulley; bevel wheel锥齿轮的当量直齿轮equivalent spur gear of the bevel gear锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear子程序subroutine子机构sub-mechanism自动化automation自锁self-locking自锁条件condition of self-locking自由度degree of freedom, mobility总重合度total contact ratio总反力resultant force总效率combined efficiency; overall efficiency组成原理theory of constitution组合齿形composite tooth form组合安装stack mounting组合机构combined mechanism阻抗力resistance最大盈亏功maximum difference work between plus and minus work 纵向重合度overlap contact ratio纵坐标ordinate组合机构combined mechanism 最少齿数minimum teeth number 最小向径minimum radius作用力applied force坐标系coordinate frame。

Aabating 硬度降低abc 自动锅炉控制aberration 象差abjustable spanner 活动]扳手abjusting spring 蝶弹簧ablation 烧蚀ablative cooling 烧蚀冷却ablative material 烧蚀材料above critical state 超临界状态 abradability 磨耗性abrasion 磨损abrasion resistance 耐磨性abrasion test 磨损试验abrasion tester 磨耗试验机abrasion wear 磨料磨损abrasive 磨料abrasive band 砂带abrasive belt 砂带abrasive belt grinding 砂带磨光abrasive belt grinding machine 砂带磨床 abrasive cloth 砂布abrasive cut off machine 砂轮切断机 abrasive cut off wheel 切割砂轮abrasive ecp 磨料电解抛光abrasive grain 磨粒abrasive jet machining 磨料喷射加工 abrasive machining 研磨加工abrasive paper 砂纸abrasive paste 研磨膏abrasive powder 研磨粉abrasive resistance 耐磨性abrasive tool 研磨工具abrasive wear 磨料磨损abrasive wheel 砂轮abrasive wire sawing machine 砂线切割机床 abscissa 横坐标absolute 绝对的absolute acceleration 绝对加速度absolute assembler 绝对汇编程序absolute black body 绝对黑体absolute ceiling 绝对升限absolute coordinates 绝对坐标absolute digital control 绝对数字控制 amperemeter 安培计amphibian car 水陆两用汽车amphibian plane 水陆飞机amphibian robot 水陆两用机扑amphibious aircraft 水陆两用飞机amphibious automobile 水陆两用汽车amphibious car 水陆两用汽车amphibious vehicle 水陆两用汽车amplification 放大amplifier 放大器扩大器amplitude 振幅amplitude frequency response 振幅频率特性amplitude limiter 限幅器amplitude modulation 振幅灯analog computer 模似计算机analog control 模拟控制analog digital computer 模拟 数字计算机analog servomechanism 模拟伺服analog signal 模拟信号analog to digital converter 模拟 数字转换器 analogue signal for robot control 控制机扑的模拟信号 analogy 类似analysis 分析analysis of covariance 协方差分析analysis of variance 方差分析analytical balance 分析天平analytical chemistry 分析化学analytical mechanics 分析力学analyzer 分析器anchor 锚anchor bolt 地脚螺栓anchor chain 锚链anchor plate 锚板anchor windlass 起锚绞盘and circuit 与电路anemograph 风力记录仪anemometer 风速计anemoscope 风向仪anergy aneroid altimeter 无液测高计aneroid barometer 空盒气压表aneroid calorimeter 空盒量热计angle 角absolute encoder 绝对编码器absolute error 绝对误差absolute humidity 绝对湿度absolute interchangeability 完全互换性absolute measurement 绝对测量absolute motion 绝对运动absolute position of manipulator 机械手的绝对位置 absolute position of robot 机扑的绝对位置 absolute pressure 绝对压力absolute system of units 绝对单位制absolute temperature 绝对温度absolute unit 绝对单位absolute unit system 绝对单位制absolute value 绝对值absolute velocity 绝对速度absolute zero 绝对零度absorb 吸收absorbability 吸收性absorbent 吸收剂absorber 吸收剂absorptiometer 吸收计absorption 吸收absorption coefficient 吸收系数absorption dynamometer 吸收式测功器absorption factor 吸收系数absorption hygrometer 吸收湿度计absorption refrigerating machine 吸收式冷冻机 absorption refrigeration 吸收式制冷absorption refrigerator 吸收式冷冻机absorptive power 吸收率absorptivity 吸收率ac 交流交变电流ac arc welder 交羚弧焊机ac arc welding 交羚弧焊接ac edm 适应控制电火花机床ac generator 交立电机ac motor 交羚动机accelerated motion 加速运动accelerated test 加速试验accelerating ability 加速能力accelerating pump 加速泵acceleration 加速acceleration diagram 加速度图acceleration of gravity 重力加速度 angle block 角度量具angle bracket 角撑架angle cock 角旋塞angle dozer 斜角推土机angle drive 角传动angle error 角误差angle gauge 量角规angle iron 角钢angle joint 角接angle of advance 超前角angle of attack 迎角angle of bank 倾斜角angle of bite 咬入角angle of climb 爬升角angle of contact 接触角angle of countersinking 划孔角angle of crossing 交叉角angle of delay 滞后角angle of deviation 偏向角angle of elevation 仰角angle of emergence 射出角angle of ignition advance 点火提前角angle of incidence 入射角angle of inclination 倾角angle of lag 滞后角angle of lap 接触角angle of lead 升角angle of nip 咬入角angle of pitch 俯仰角angle of polarization 偏光角angle of reflection 反射角angle of refraction 折射角angle of repose 休止角angle of rest 休止角angle of screw thread 螺纹截形角angle of stall 失速角angle of thread 螺面角angle of torsion 扭转角angle of twist 扭转角angle of yaw 偏航角angle shears 剪角铁机angle transmission 角传动angle type axial piston pump 弯体式轴向活塞泵 angle valve 角阀acceleration pick up 加速度传感器 acceleration time 加速时间 accelerator 加速器accelerator lever 加速栖杆 accelerator pedal 加速皮板 accelerator pump 加速泼 accelerograph 自记加速计 accelerometer 加速度计acceptable noise level 容许噪声 acceptance certificate 验收证瞄 acceptance test 验收试验accessories 附件accessory 附属品accident 事故accident prevention 事故预防 accidental 偶然的accidental error 偶然误差accounting machine 会计计算机 accumulated error 累积误差 accumulated pitch error 同节累积误差 accumulator 电池accumulator capacity 蓄电池容量 accumulator car 蓄电池汽车 accumulator plate 蓄电池极板 accuracy 精确度accuracy control 精确控制accuracy grade 精度等级accuracy life 精确度寿命accuracy of alignment 对中精度 accuracy of instrument 仪表精度 accuracy of measurement 测量精度 accuracy of reproduction 再现精度 accuracy to size 尺寸精度accurate adjustment 精密蝶accurate grinding 精密磨削accurate measurement 精确测量 acetylcellulose 醋酸纤维素acetylene 乙炔acetylene burner 乙炔燃烧器乙快焊炬 acetylene cutting 氧炔切割acetylene cutting machine 氧炔切割机 acetylene gas 乙炔气acetylene generator 乙炔发生器 acetylene producer 乙炔发生器 angstrom 埃angular acceleration 角加速度angular ball bearing 径向止推滚珠轴承angular belt drive 角皮带传动angular contact ball bearing 径向止推滚珠轴承 angular cutter 角铣刀angular deviation 角偏差angular displacement 角位移angular frequency 角频率angular momentum 角动量angular motion 角运动angular resolution 角度分辨率angular velocity 角速度aniline 苯胺animal charcoal 骨炭animal oil 动物油anion 阴离子anisotropic material 蛤异性物质anisotropy 蛤异性annealing 退火annealing box 退火箱annealing furnace 退火炉annealing temperature 退火温度annual consumption 年用量annular 环形的annular combustion chamber 环形燃烧室annular float 环状浮子annular flow 环形流annular furnace 环形炉annular groove 环形槽annular magnet 环形磁铁annular nozzle 环形喷嘴annular space 环形间隙annular spring 弹簧环annular valve 环状阀annulus 环状空间anode 正极anode film 阳极被覆膜anode mechanical machining 阳极机械加工 anode sputtering 阳极溅射anodic dissolution 阳极溶解anodic machining 阳极机械加工anodic oxidation 阳极溶解anodic protection 阳极保护acetylene torch 乙炔燃烧器乙快焊炬 acetylene welding 乙炔焊接achromatic 消色差的achromatic colour 无彩色achromatic lens 消色差透镜acicular cast iron 针状结构铸铁 acicular structure 针状结构acid 酸acid bessemer converter 酸性转炉acid bessemer process 酸性转炉炼钢法 acid brick 酸性砖acid converter 酸性转炉acid converter process 酸性转炉炼钢法 acid number 酸价acid open hearth furnace 酸性平炉 acid process 酸性炼钢法acid proof 耐酸性的acid proof coating 耐酸保护层acid proof paint 耐酸涂料acid rain 酸雨acid resistance 耐酸性acid resistant alloy 抗酸合金acid resistant steel 耐酸钢acid resisting 耐酸性的acid resisting alloy 抗酸合金acid resisting paint 耐酸涂料acid resisting steel 耐酸钢acid solution 酸溶液acid steel 酸性钢acid value 酸价acidity 酸度acierage 表面钢化acieration 表面钢化acme thread 亚克米螺纹aco 最佳适应控制acoustic 声的acoustic absorbing material 吸音材料 acoustic analysis 声学分析acoustic diagnosis 音响诊断acoustic gas analyzer 声学气体分析器 acoustic inspection 音响检查acoustic insulation 隔音acoustic oscillations 声振动acoustic printing machine 声动印刷机 anodic removing 电解加工anodic solution 阳极溶解 antechamber 预燃室antenna 天线anthracite 无烟煤anti icer 防冰装置anticathode 对阴极anticlockwise rotation 反时针方向旋转 anticollision system 防撞系统 anticorrosion film 耐蚀薄膜 anticorrosive agent 防腐蚀剂 anticorrosive alloy 耐蚀合金 anticorrosive composition 防腐蚀剂 anticorrosive paint 防蚀涂料 antidazzle light 避眩灯antidazzle visor 防眩罩antidetonant 防爆剂antifoamer 防泡剂antifreeze 防冻剂antifreezing agent 防冻剂antifriction alloy 抗摩合金 antifriction bearing 滚动轴承 antifriction cast iron 抗摩铸铁 antifriction guide 滚动导轨 antifriction material 耐摩材料 antifriction metal 抗摩合金antiglare light 避眩灯antiknock 抗爆的antiknock agent 防爆剂antiknock fuel 抗爆震燃料antiknock gasoline 抗爆汽油antiknock quality 抗爆性antimonial lead 锑铅antimony 锑antinode 波腹antioxidant 抗氧化剂antiresonance 反共振antirusting paint 防蚀涂料antiscale composition 防垢剂 antiseptic 防腐剂antiskid chain 防滑链antiskid tire 防滑轮胎antiskid tyre 防滑轮胎antiwear additive 抗磨添加剂acoustic resonance 声共振acoustic signal 音响信号acoustic velocity 声速acoustic vibrations 声振动acoustic wave 声波acoustics 声学actinometer 露光计action 酌action turbine 冲动式透平activated carbon 活性炭activation 活化activation energy 活化能active current 有功电流active energy meter 累积瓦特计active power 有效功率active solar heating 织式太阳能供暖activity 活度actual horsepower 有效马力actual size 实际尺寸actual stress 实际应力actuator 执行机构actuator of robot 机扑的操　构adaptability 适应性adaptable 可以应用的adaptable robot 适应性机扑adapter 匹配器adapter sleeve 紧固套adaptive control 适应控制adaptive control optimization 最佳适应控制adaptive controlled discharge machine 适应控制电火花机床 adaptive controlled machine 自适应控制机床adaptive robot control 机扑的适应控制adaptive robot system 机扑的适应系统adaptive robot technical complex 适应性机扑综合技术 adaptive sensor guided robot 传感曝制自适应机扑adc 模拟 数字转换器addendum 齿顶addendum angletip angle 齿顶角addendum circle 齿顶圆addendum cone 齿顶addendum modification 齿顶修正addendum modification coefficient 齿顶修正系数adder 加法器additive 添加剂 anvil 测砧anvil block 砧座anvil face 砧面aperiodic motion 非周期运动aperture 口径aperture ratio 口径比aplanat 齐酶镜aplanatic 消球差的aplanatic lens 齐酶镜apochromat 复消色差透镜 apochromatic lens 复消色差透镜 apothem 内切圆半径apparatus 装置apparent density 表观密度apparent expansion 视在膨胀apparent force 表观力apparent moisture 表面水分apparent power 表观功率apparent specific gravity 外表比重 appearance 外形application 应用application point 酌点application program 应用程序applied elasticity theory 应用弹性学 applied mechanics 应用力学applied thermodynamics 应用热力学 approximate analysis 近似分析 approximate calculation 近似计算 approximate model 近似模型 approximate value 近似值 approximation 近似apron 挡板apron conveyor 板式输送机aqua ammonia 氨水aqueous solution 水溶液arbor 心轴arbormandrel 心轴arc 电弧arc cutting 电弧切割arc discharge 电弧arc furnace 电弧炉arc lamp 弧光灯arc voltage 电弧电压arc welder 电焊机adherence 附着adherometer 粘附计adhesion 附着adhesion coefficient 附着系数 adhesion wear 胶合磨损adhesion weight 附着重量adhesive 粘着剂adhesive force 粘着力adhesive joint 附着接头adhesive strength 粘着强度adhesivity 粘附性adiabatic calorimeter 绝热量热器 adiabatic change 绝热变化adiabatic combustion 绝热燃烧 adiabatic compression 绝热压缩 adiabatic curve 绝热线adiabatic efficiency 绝热效率 adiabatic equilibrium 绝热平衡 adiabatic expansion 绝热膨胀 adiabatic exponent 绝热指数adiabatic line 绝热线adiabatic process 绝热过程adiabatic temperature 绝热温度 adjustable 可蝶的adjustable bearing 可蝶轴承 adjustable guide vane 可导叶 adjustable pitch propeller 可掂螺旋桨 adjustable reamer 可第铰刀adjustable resistance 可变电阻 adjustable shell reamer 可底管铰刀 adjustable speed motor 蒂电动机 adjustable tap 可悼锥adjustable wrench 可靛手adjustadle wrench 活动]扳手adjuster 蝶工adjustible tap 可刀丝锥adjusting 蝶adjusting bolt 蝶螺栓adjusting bush 第套筒adjusting cam 蝶凸轮adjusting device 蝶装置adjusting gauge 蝶量规adjusting nut 蝶螺母adjusting screw 蝶螺钉 arc welding 电弧焊接arc welding machine 电焊机arc welding robot 电弧焊机扑arch 拱arch dam 拱坝arched beam 拱梁arched girder 拱梁archimedes' principle 阿基米德原理 archimedes' spiral 阿基米德螺线archimedes' worm 阿基米德蜗杆architecture 建筑术architecture of robot computer 机扑电脑结构 area 面积area of bearing 支承面area of contact 接触面积areal velocity 面积速度areometer 比量计argon arc welding 氩弧焊argon laser 氩激光器arithmetic mean 算术平均arithmetic mean value 算术平均值arithmetic progression 算术级数arithmetic robot processor 机扑运算处理装置 arithmetic unit 运算装置arm 臂arm of wheel 轮辐armature 电枢armature core 电枢铁芯armature winding 电枢绕组armature winding machine 电枢绕线机armco iron 阿姆克铁armor plate 装甲板armor plate mill 装甲钢板轧机armored cable 装甲缆armored car 装甲车armored glass 络网玻璃armored hose 钢丝包皮软管armored personnel carrier 军用载人装甲车 armored vehicle 装甲车armour piercing shell 穿甲弹armoured hose 钢丝包皮软管aromatic base crude oil 芳香族石油 arrangement 排列arrangement plan 布置图adjusting valve 第阀adjusting wedge 蝶楔块adjustment 蝶adjustment range 蝶范围adjustment robot 第式机扑 admiralty brass 船用黄铜 admissible 容许的admissible load 容许负荷 admission 进气admission cam 进气凸轮admission period 进气期间 admission pipe 进气管admission port 吸气口admission pressure 进气压力 admission stroke 进气冲程 admission valve 进气阀admittance 导纳admixture 掺和物adsorbent 吸附剂adsorption 吸附advance 提前advanced ignition 提前点火 advanced opening 提前进气aecp 磨料电解抛光aerator 通气设备aerial 天线aerial cableway 架空死aerial camera 航空摄影机aerial conveyor 高架式输送机aerial railway 高架铁路aerial ropeway 架空死aerodrome 飞机场aerodynamic 气体动力的 aerodynamic bearing 空气动力轴承 aerodynamic brake 空气动力制动装置 aerodynamic drag 气动阻力 aerodynamic heating 空气动力加热 aerodynamic lift 空气动力升力 aerodynamic moment 空气动力力矩 aerodynamic similarity 气动力相似 aerodynamical 气体动力的 aerodynamical action 气体动力酌 aerodynamical balance 空气动力天平 aerodynamical heating 动力加热 arrow engine w 形发动机arrowhead 箭头art casting 艺术铸件artesian well 钻井articulated 铰链的articulated arm 关节杆articulated connecting rod 副连杆articulated coupling 活节联接器articulated mechanism 铰接机构articulated pipe 关节管articulated robot 多关节型机扑articulated trolleybus 铰接式无轨电车 articulated vehicle 铰接式汽车articulation 关节artificial 人工的artificial abrasive 人造磨料artificial aging 人工时效artificial brain 人工脑artificial diamond 人造金刚石artificial draft 人工通风artificial drying 人工干燥artificial fiber 人造纤维artificial fibre automobile 人造纤维汽车 artificial fibre plane 人造纤维飞机artificial fuel 人造燃料artificial graphite 人造石墨artificial horizon 人工水平仪artificial illumination 人工照明artificial intelligence 人工智能artificial intelligence automobile 人工智能汽车 artificial leather 人造革artificial lighting 人工照明artificial liquid fuel 人造液体燃料artificial petroleum 人造石油artificial resin 合成尸artificial satellite 人造卫星artificial ventilation 人工换气artificial vision 人工视觉as cast condition 铸态asbestos 石棉asbestos brake band 石棉制动摩擦带asbestos cardboard 石棉纸板asbestos cloth 石棉布asbestos gasket 石棉垫圈aerodynamical resistance 气动阻力 aerodynamics 空气动力学aerodyne 重航空器aeroelasticity 气动力弹性 aeroengine 航空发动机aeroenging 飞机发动机aerofoil 机翼aerofoil profile 翼形剖面aerofoil theory 机翼理论 aerogenerator 风力发电机 aerometer 气体比重计aeronautics 航空学aeroplane 飞机aeropulse engine 脉动式喷气发动机 aerosol 悬浮微粒aerostat 轻航空器aerostatic bearing 空气静力轴承 aerostatics 空气静力学 aerothermoelasticity 气动热弹性 aerotrain 飞行式无轨列车 aeroturbine 航空涡轮机affinity 亲合势aft engine 尾发动机after sales service 提供维修服务 afterburner 加力燃烧室 afterburning 烧完aftercombustion 烧完aftercooler 最终冷却器afterheat 余热aftertreatment 后处理age hardening 时效硬化ageing 时效agglomerating furnace 烧结炉 agglomerating plant 烧结机 agglomeration 烧结aggregate 机组aggressive gas 腐蚀性气体 aggressive medium 腐蚀介质aging 时效aging test 老化试验agitating truck 混凝土搅拌汽车 agitation 搅拌agitator 搅拌器agricultural aircraft 农用飞机 asbestos plate 石棉板asbestos wool 石棉绒ascending stroke 上升冲程ash 灰ash composition 灰分组成ash content 灰分ash ejector 放灰器排灰器ash free fuel 无灰分燃料ash hoist 起灰机ash pit 灰槽ash removal 除灰aspect ratio 展弦比asphalt 沥青asphalt base crude oil 沥青基原油asphalt paper 沥青纸aspirating stroke 吸气冲程aspiration hygrometer 通风湿度计aspirator 吸引器assay 试金assay balance 试金天平assay furnace 试金炉assembler 装配工assembler programming system. aps 汇编程序系统 assemblererector 装配工assembling 安装assembling machine 安装机;装配机械assembling robot 装配机扑assembling shop 装配车间assembling tool 装配工具assembly 安装assembly automation 装配自动化assembly conveyor 装配输送带assembly drawing 装配图assembly fixture 装配夹具assembly industrial robot 装配用工业机扑 assembly line 装配线assembly plant 装配厂assembly process 装配过程assembly robot 装配机扑assembly shop 装配车间assembly stand 装配架assembly station 装配站assembly technology 装配工艺assembly unit 装配单位agricultural airplane 农用飞机 agricultural implements 农具 agricultural machine 农业机器 agricultural machines 农业机械 agv 无人搬运车ahead turbine 推进汽轮机aileron 副翼ailerons 副翼air 空气air accumulator 空气蓄压器air bearing 空气轴承air bleed valve 放气阀air bleeder 放气阀air brake 空气制动器air breathing engine 喷气发动机 air buffer 空气缓冲器air car 气垫车air cell engine 旋风式发动机air chamber 空气室air chamber engine 旋风式发动机 air chipper 气錾air chuck 压缩空气式卡盘air circulation 空气循环air classifier 空气分级器air cleaner 空气滤清器air cleaning 空气净化air cock 气旋塞air compressor 空气压缩机air conditioner 空气第器air conditioning 空气第air consumption 空气消耗量air container 储气罐air contamination 空气污染air conveying 气力输送air cooled 气冷的air cooled condenser 空气冷凝器 air cooled cylinder 气冷气缸air cooled engine 气冷式发动机 air cooled turbine 气冷式透平air cooled valve 气冷阀air cooler 空气冷却器air cooling 空气冷却air cooling apparatus 空气冷却器 air cooling fin 空气冷却片 associative read only memories. aroms 相联只读存储器 astatic governor 无定向蒂器astern turbine 倒车轮机astronautics 宇宙航行学astronomical telescope 天体望远镜asymmetry 不对称asymptote 渐近线asymptotic stability 渐近稳定度asynchronous communication adapter. aca 异步通信适配器asynchronous generator 异步发电机asynchronous machine 异步电机asynchronous motor 感应电动机asynchronous robot control 机扑异步控制atc 自动换刀装置athermanous 不透热的atmometer 汽化计atmosphere 大气atmospheric braking 大气制动atmospheric condenser 大气式冷凝器atmospheric cooler 大气式冷却器atmospheric corrosion 大气腐蚀atmospheric moisture 大气湿度atmospheric pollution 空气污染atmospheric pressure 大气压力atom 原子atomic battery 原子能电池atomic clock 原子钟atomic energy 核能atomic fuel 核燃料atomic heat 原子热atomic hydrogen welding 原子氢焊接atomic nucleus 原子核atomic number 原子序数atomic power 原子动力atomic powered aircraft 原子飞机atomic powered ship 核船atomic propulsion 核动力推进atomic reactor 核反应堆atomic submarine 核潜艇atomic weight 原子量atomization 雾化atomizer 喷雾器atr 自动带读出器attachment 附属装置air current 气流air curtain 空气幕air cushion 气垫air cushion ship 气垫船air cushion shock absorber 空气缓冲器 air cushion vehicle 对地效应飞行器air cylinder 空气气缸air damper 空气缓冲器air damping 空气阻尼air density 空气密度air distributor 空气分配器air drag 空气阻力air drill 风钻air driven vibrator 风动振动机air drying 空气干燥air duct 风道air ejector 空气喷射器air elutriator 空气分离器风选器air engine 空气发动机air filled tyre 气轮胎air filled tyre pneumatic tyre 气轮胎 air filter 空气滤清器air flow 气流air flue 风道air fuel mixture 空气燃料混合物air fuel ratio 空气燃料比air gap 空隙air gas 空气煤气air gauge 气动测微仪air hammer 空气锤air hammer drill 风动凿岩机air hardening 空气淬火air hardening steel 空气硬化钢air heater 空气加热器air heating 热风采暖air heating furnace 热风炉air hoist 气葫芦air hole 通风孔air hose 风管air humidity 空气湿度air infalting 充气air infiltration 漏风air inflating 轮胎打气air injection 空气喷射 attemperator 减温器过热降低器attendance instruction 维护规程attenuation constant 衰减常数attenuator 衰减器attitude control 姿态控制attraction 引力attractive force 引力attrition 磨耗attrition test 磨损试验audible sound 可听音audio frequency 声频auger 回转式钻岩机auger drill 回转式钻岩机austenite 奥氏体austenitic steel 奥氏体钢auto hoist 升车机auto levelizer 到装置auto lift 车辆提升机auto repair shop 汽车修理车间auto tire 汽车轮胎auto tyre 汽车外轮胎autoclave 高压釜autocollimator 自动准直仪autofrettage 自应力加工autogenous cutting 气割autogenous welding 气焊autogyro 旋翼飞机autoignition 自发火autoloader 自动装载机automated assembly 自动装配automated inspection 自动检验automated production 自动化生产automated warehouse 自动仓库automatic 自动的automatic arc welder 自动弧焊机automatic arc welding machine 自动弧焊机 automatic assembly machine 自动装配机 automatic block 自动闭塞装置automatic boiler control 自动锅炉控制 automatic brake 自动制动器automatic calling equipment. ace 自动呼叫装置 automatic charge 自动装料automatic checking 自动检验automatic checking machine 自动检验机air injection diesel engine 空气喷射柴油发动机 air injection engine 空气喷射柴油发动机air inlet 进气口air inlet valve 进气阀air insulation 空气绝缘air intake 进气口air intake valve 进气阀air isolation 空气绝缘air jacket 空气套air jet 空气喷嘴air lift 空气升液泵air liquefier 空气液化器air lubrication 空气润滑air main 空气周路air micrometer 气动测微仪air mobile vehicle 空气怜车air motor 气动发动机air operated machine 风动机air passage 风道air pipe 气管air pollution 空气污染air power hammer 空气锤air preheater 空气预热器air pressure gauge 空气压力计air pressure reducer 空气减压器air pressure test 空气压力试验air proof 不透气的air pump 空气泵air purification 空气净化air quenching 空气淬火air rammer 风动夯air receiver 储气罐air refrigerating machine 空气制冷机air register 电器空气第器air reservoir 储气罐air resistance 空气阻力air separation 空气分离air separator 空气分离器风选器air speed indicator 空速指示器空速表示器air spring 空气弹簧air stream 气流air surface condenser 空气冷凝器air suspension 气动悬架装置air tamper 风动夯 automatic circuit breaker 自动断路器自动开关 automatic clutch 自动离合器automatic control 自动控制automatic control system 自动第系统automatic control theory 自动控制理论automatic controller 自动第器automatic coupler 自动联结器自动车钩automatic coupling 自动联结器自动车钩automatic current recording meter 自动记录电疗 automatic cycle 自动循环automatic defrosting 自动除霜automatic digital computer. adc 自动数字计算机 automatic dischargingapparatus 自动卸货装置automatic drilling machine 自动钻床automatic feed 自动进给automatic gear milling machine 自动齿轮铣床automatic gear shaping machine 自动插齿机automatic gearbox 自动变速器automatic gripper system 自动抓手装置automatic guided vehicle 无人搬运车automatic head changer 自动更换轴箱装置automatic herringbone gear planer 自动人字齿轮刨床 automatic hobbing machine 自动滚齿机automatic inspection machine 自动检验器automatic lathe 自动车床automatic level control 自动水平控制automatic line 自动化生产线automatic loom 自动织布机automatic lubrication 自动润滑automatic lubricator 自动润滑器automatic machine 自动机床automatic milling machine 自动铣床automatic model recognition 模型自动识别automatic operation 自动操作automatic orientation 自动定向automatic pallet changer 随行夹具自动更换装置 automatic picture transmission. apt 图象自动传输 automatic pilot 自动导航装置automatic positioning device 自动定位装置automatic press 自动压力机automatic program controlled robot 程序控制式自动机扑 automatic programming 自动编程序automatic recorder 自动记录器自记器automatic regulating system 自动第系统air thermometer 空气温度计air tight 不透气的air tight joint 气密接头air tightness 气密性air transport 气力输送air tube 气管air turbine 空气涡轮机air valve 气阀air vent 通风孔air washer 净气器空气选净器airborne camera 航空摄影机aircraft 飞机aircraft carrier 航空母舰aircraft engine 飞机发动机aircraft gas turbine 航空燃气涡轮机aircraft industry 航空工业aircraft instrument 航空仪表aircraft mechanician 飞机机械师aircraft tractor 飞机牵引车airdrome 飞机场airfoil 机翼airless injection 无气喷射airless injection diesel engine 无气喷射柴油发动机 airliner 班机airplane 飞机airplane carrier 航空母舰airplane engine 飞机发动机airport 航空港airscrew 螺旋桨airship 飞艇airstrip 跑道ajm 磨料喷射加工alarm 警报alarm clock 闹钟alarm signal 警告信号alarm system 告警系统alarming apparatus 警报装置albedo 反照率alcohol 醇alcohol meter 乙醇计alcohol thermometer 酒精温度计algebraic equation 代数方程algorithm 算法alidade 照准仪 automatic regulator 自动第器自动蝶器automatic release 自动释放automatic resetting 自动复位automatic robot 自动机扑automatic screw cutting lathe 自动螺丝车床 automatic screw machine 自动螺丝车床automatic sorting 自动分类automatic spot welding 自动点焊automatic steering 自动转向automatic stop 自停automatic switch 自动开关automatic tape reader 自动带读出器automatic temperature control 自动温度控制 automatic temperature controller 自动温度控制器 automatic tool changer 自动换刀装置automatic tool changer. atc 工具自动交换装置 automatic train control 自动列车控制automatic train stop 自动停车装置automatic transmission 自动变速器automatic valve 自动阀automatic warehouse 自动仓库automatic weigher 自动秤automatic welder 自动焊机automatic welding 自动焊接automatic welding machine 自动焊机automatic wire feed 自动穿丝automatic work changer 自动换工件装置automatic workpiece change 自动工件交换 automatic zero adjustment 自动零位蝶 automatically operated robot 自动操　扑 automation 自动化automicrometer 自动千分尺automobile 汽车automobile crane 汽车起重机automobile engine 汽车发动机automobile oil 汽车润滑油automobile plant 汽车工厂automobile tire 汽车轮胎automobile train 汽车列车automobile tyre 汽车外轮胎automotive body 汽车车身automotive body press 汽车车身压床automotive chassis 底盘automotive engine 汽车发动机alignment 定心alignment pin 定位销alignment system supply 导系统电源 alitizing 表面渗铝alkali 碱alkaline battery 硷性蓄电池alkaline earth metal 碱土族金属alkaline solution 碱性溶液alkaline storage battery 碱蓄电池 alkalinity 碱度alkyd resin 醇酸尸all metal construction 全金属结构all purpose 万能的all steel body 全钢车身all weather aircraft 全天候飞机all wheel drive 全轮驱动allen wrench 方孔螺钉头用扳手allidade 游标盘alligator shears 杠杆式剪床allotrope 同素异形体allotropic transformation 同素异形变化 allotropism 同素异形allotropy 同素异形allowable 容许的allowable bearing pressure 容许支承压力 allowable clearance 允许间隙allowable error 容许误差allowable load 容许负荷allowable pressure 容许压力allowable stress 容许应力allowable temperature 容许温度 allowance for machining 加工余量alloy 合金alloy cast iron 合金铸铁alloy for cutting tools 切悉具合金alloy pig iron 合金生铁alloy steel 合金钢alloy tool steel 合金工具钢alloying component 合金成分alloying constituent 合金成分alloying element 合金元素alnico 阿尔尼科合金alphameric code 字母数字码alternate load 交替负载 automotive engineering 汽车工程automotive fuel 汽车燃料automotive industry 汽车工业automotive suspension 汽车悬架automotive vehicles 车辆autonomous system 自激系统autopilot 自动导航装置autostabilizer 自动稳定装置autosyn 自动同步机autotransformer 自耦变压器auxiliary air 补充空气auxiliary connecting rod 辅助连杆auxiliary device 辅助装置auxiliary drive 辅助驱动auxiliary engine 辅助发动机auxiliary equipment 辅助设备auxiliary fuel tank 备用油箱auxiliary robot 辅助机扑auxiliary spring 副弹簧auxiliary time 辅助时间auxiliary transmission 副变速器auxiliary turbine 辅助透平auxiliary valve 辅助阀auxiliary ventilator 辅助通风器availability time 可用时间available energy 有效能available head 有效落差average 平均average error 平均误差average ignition delay time 平均哗廷时average life 平均寿命average load 平均荷重average pressure 平均压力average relative discharge duration 平均相对放电时间 average speed 平均速度average tempetature 平均温度average value 平均值average velocity 平均速度aviation 航空aviation fuel 航空燃料aviation gas turbine 航空燃气轮机发动机aviation gasoline 航空汽油aviation industry 航空工业aviation oil 航空用机油alternate stress 交变应力alternating current 交流交变电流alternating current arc welder 交羚弧焊机 alternating current bridge 交羚桥alternating current commutator motor 交聋劣式电动机 alternating current generator 交立电机alternating current measuring bridge 交羚桥 alternating current motor 交羚动机alternating current servomotor 交僚服马达altimeter 高度计altitude 高度altitude engine 高空发动机altitude indicator 高度指示器alumina 铝氧土aluminium 铝aluminizing 表面渗铝aluminum alloy 铝合金aluminum brass 铝黄铜合金aluminum bronze 铝青铜aluminum casting 铝铸件aluminum oxide 铝氧土aluminum paint 铝涂料aluminum piston 铝质活塞aluminum rivet 铝铆钉alundum 氧化铝amalgam 汞齐amber 琥珀ambient 周围的ambient air 周围的空气ambient conditions 环境条件ambient medium 周围介质ambient noise 环境噪声ambient pressure 周围压力ambient temperature 周围温度ambient vibration 周围振动ambulance car 救护车amendment 修正amm 阳极机械加工ammeter 安培计ammonal 阿芒拿ammonia 氨ammonia absorption refrigerator 氨吸收冷冻机 ammonia compression refrigerator 氨气压缩冷冻机 ammonia compressor 氨气压缩机 avionics 航空电子学avogadro's number 阿佛伽德罗数avometer 安伏欧计awc 自动换工件装置axes of coordinates 坐标轴axial 轴向的axial admission 轴向导入axial blower 轴聊风机axial clearance 轴向间隙axial compressor 轴两压气机axial direction 轴向axial fan 轴两通风机axial flow 轴流axial flow pump 轴撩axial flow reaction turbine 轴链动式透平 axial flow turbine 轴两透平axial force 轴向力axial load 轴向负载axial module 轴向模数axial moment of inertia 轴惯性矩axial piston motor 轴向活塞马达axial piston pump 轴向活塞泵axial pitch 轴向节距axial plane 轴面axial play 轴向游axial radial flow pump 混撩axial runout 轴向摆动axial section 轴向载面axial stress 轴向应力axial symmetry 轴对称axial thrust 轴向推力axial turbocharger 轴两透平增压器axiom 公理axis 轴axis of abscissas 横坐标轴axis of ordinates 纵坐标轴axis of projection 投影轴axis of rotation 回转轴axis of symmetry 对称轴axisymmetric body 轴对称物体 axisymmetric flow 轴对称流axle 车轴axle base 轴距axle bearing 轴轴承。

Piping work: 铺管工程Steam trace: 加热蒸汽管道Cutting:切割socket weld 承插焊接fillet weld 角焊 ,填角焊branch connection 分支接续fabrication tolerance. 制造容差local heat treatment 局部热办理threaded pipe 螺纹管seal welding. 密封焊接flange joint凸缘接头undercut 底切feeder 馈电线conduit outlet 电线引出口seal fitting密封接头,密封配件Screw thread lubricant 螺纹润滑剂Seal: 绝缘层weld reinforcement焊缝补强lock washer 锁紧 [止动 , 防松 ] 垫圈electrical panel. 配电板 ,配电盘nipple 螺纹接头zinc plated. 镀锌的ring joint环接,围缘接合bolt 螺栓control:控制器National Electrical Code全国电气规程master schedule 主要图表 , 综合图表 , 设计任务书 , 主要作业表torque wrench 转矩扳手job site 施工现场flange connection. 凸缘联接Hard hat：安全帽Goggles：护目镜stockpile 储存packing list 装箱单crate: 柳条箱purchased material list 原资料进货单back-feed 反响wire coil 线盘，线卷，NPT thread. 美国标准锥管螺纹cable gland 电缆衬垫terminal block 线弧 , 接头排接线盒,接线板,线夹power drill 机械钻connector. 接线器insulated sleeve 绝缘套管wire connector 接线器wire terminal 电线接头control wiring控制线路motor lead 电动机引出线power wiring 电力布线tender document．供给证件orifice plate. 挡板nut 螺母flange gasket 法兰垫片dimensional inspection尺寸检验burn through烧蚀piping system. 管道系统reinforcement of weld增强焊缝fabrication. 制造dye penetrant examination 染料浸透试验法magnetic particle examination磁粉检验girth weld 环形焊缝cement lined piping水泥衬里weld joint焊缝,焊接接头spool drawing管路图,管路详图.spot test 抽查 , 就地测试butt weld对接焊缝Random Radiography 随机射线照相检查radiographic examination射线照相检查assembly.装置erection 架设examination 试验cable tray.电缆盘rigid steel conduit钢制电线管power control功率控制arc welding电弧焊control cable 控制电缆操控索normal bend 法向 [法线 ] 弯管cable glands: 电缆衬垫exfoliation 剥落power receptacle 电力插座grounding conductor接地导体lighting fixture照明器械junction box分线箱race way 电缆管道terminal box 接线盒distribution board 配电盘 , 配电屏receptacle 插座tumble switch. 翻转开关 ,拨动式开关cathodic protection system阴极保护系统Circuit breaker 断路开关amplifier panel放大器盘control console控制台electrical material 电气资料convenience receptacle.电源插座cable gland电缆衬垫TIG ： Tungsten-arc Inert-Gas welding钨极电弧惰性气体保护焊filler rod 焊条tensile strength抗张强度shield gas 保护气体shield jig 保护夹具high frequency generator. 高频发电机welding rod焊条filler metal焊料, 焊丝shop fabrication车间制造field installation现场安装welding bead 焊道both sides welding. 双面焊接residual stress 节余应力electrode 电焊条condensation 冷凝longitudinal. 纵向的horizontal line水平线circumferential joint周圈接缝nondestructive examination. 非破坏性检验,qualification:合格性construction work 施工工程welded joint 焊接缝焊接节点gas cutting.气割arc cutting 电弧切割grind off磨掉metallic luster金属光彩Screwed Piping Joints 螺丝状的管接头gouging . 刨削槽成形不良用语aberration 色差atomization ? 化bank mark ?料纹bite 咬入blacking hole涂料孔(铸疵) blacking scab涂料疤blister 起泡blooming起霜blow hole破孔blushing 泛白body wrinkle侧壁皱纹breaking-in冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂缝checking 龟裂chipping修整表面缺点clamp-off铸件凹痕collapse 塌陷color mottle色斑corrosion 腐化crack 裂缝crazing 碎裂crazing 龟裂deformation变形edge 切边碎片edge crack 裂边fading 褪色filler speak填补料斑fissure 裂纹flange wrinkle凸缘起皱flaw 刮伤flow mark流痕galling毛边glazing 圆滑gloss 光彩grease pits 污斑grinding defect磨痕haircrack 发裂haze 雾度incrustation 水锈indentation压痕internal porosity内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺点overflow溢流peeling 剥离pit 坑 pitting corrosion点状腐化plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂零落riding 凹陷sagging 松垂saponification皂化scar 疤痕scrap 废料scrap jam 废料堵塞scratch 刮伤 /划痕scuffing深冲表面划伤seam 裂缝shock line 模口挤痕short shot 充填不足shrinkage pool凹孔sink mark凹痕skin inclusion表皮摺叠straightening矫直streak 条状痕surface check 表面裂缝surface roughening 橘皮状表皮皱摺surging 颠簸sweat out 冒汗torsion 歪曲warpage 翘曲waviness 波痕webbing 熔塌weld mark焊痕whitening白化wrinkle皱纹模具常用刀具与工作法用语adjustable spanner 活动扳手angle cutter 角铣刀anvil 铁? arbour 心轴backing 衬垫belt sander 带式打磨机buffing抛光chamfering machine倒角机chamfering tool去角刀具chisel 扁錾chuck 夹具 compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint十字接头cutting edge clearance 刃口余隙角drill stand钻台edge file 刃用锉刀file 锉刀flange joint凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping剥离工具T-slot T 形槽tool for lathe车刀tool point angle刀刃角tool post 刀架tosecan 划线盘trimming去毛边waffle die flattening压纹效平wiper脱模钳wrench 螺旋扳手电脑关系用语3D modeling三次元模拟access 通路animation 卡通电影application 应用board 基板bug 故障bus 汇流排CAD电脑辅助设计CAE 电脑辅助工程解析CAM电脑辅助制造cassette 卡座color display彩色显示器command 指令communication通讯compact 精简小型computer 电脑copy 复制cursor 游标curve modeling曲面模拟database 资料库design 设计digitizing数位化disk 磁碟dot 点eyelet 眼孔 floppy磁碟片format 格式化graphic 圆解hardware 硬体honeycomb 蜂巢interface 界面know how诀要laser printer 雷射印表机lay out 部署memory 记忆memory swap 交换记忆microprocessor 微办理器modeling造型module 模组monitor萤幕mouse 滑鼠need 需求network网路new version 新版on line上线中option 选择PC 个人电脑plotter 绘图机program 程式scanning 扫描simulation模拟software 软体solid model 实体模型system 系统tape 磁带terminal 终端机texture 构造trim 修边venter 排气风扇word processor 文书办理器各种冲模加工关系用语barreling 滚光加工belling压凸加工bending 曲折加工blanking 下料加工bulging撑压加工burring 冲缘加工cam die bending 凸轮曲折加工caulking ? 合加工coining压印加工compressing 压缩加工compression bending 押曲折加工crowning凸面加工curl bending卷边曲折加工curling卷曲加工cutting 切削加工dinking切断蕊骨double shearing 叠板裁断drawing引伸加工drawing with ironing抽引圆滑加工embossing 浮花压制加工extrusion 挤制加工filing锉削加工fine blanking 精美下料加工finish blanking 光制下料加工finishing精整加工 flanging凸缘加工folding 折边曲折加工 folding 摺叠加工forming成形加工 impact extrusion 冲击挤压加工indenting压痕加工 ironing引缩加工knurling滚花 lock seaming固定接合louvering百页窗板加工 marking 刻印加工necking颈缩加工 notching冲口加工parting 分断加工piercing冲孔加工progressive bending 连续曲折加工progressive blanking连续下料加工progressive drawing连续引伸加工progressive forming连续成形加工reaming 铰孔加工restriking二次精冲加工riveting ? 接加工roll bending滚筒曲折加工roll finishing滚压加工rolling压延加工roughing 粗加工scrapless machining 无废料加工seaming 折弯重叠加工shaving 缺口修整加工shearing 切断加工sizing 精压加工 /更正加工slitting割缝加工spinning 卷边 ?接staking ?固 stamping 锻压加工swaging 挤锻压加工trimming整缘加工upsetting 锻粗加工wiring抽线加工冲压机械及周边关系用语back shaft 支撑轴blank determination胚料睁开bottom slide press 下传动式压力机board drop hammer 板落锤brake 煞车buckle 剥砂面camlachie cramp 铸包casting on flat ? 合chamotte sand 烧磨砂charging hopper加料漏斗clearance 缝隙closed-die forging合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining离合器覆盖coil car带卷起落运输机coil cradle卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调理螺钉core compound 砂心黏结剂counter blow hammer对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模吵嘴度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core埋入砂心filling in填砂film play液面花纹fine blanking press 精美下料冲床forging roll辊锻机finishing slag炼後熔渣fly wheel飞轮fly wheel brake飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction摩擦friction brake摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块指引部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传递装置hammer 槌机hand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching微调尺寸isothermal forging恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic转向机构land 模具直线刀面部level 水平loader 供料器 unloader卸料机loop controller 闭回路控制器 lower die下模micro inching device微寸动装置microinching equipment微动装置motor 马达 moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device防超载装置pinch roll导正滚轮pinion 小齿轮 pitch节距pressfit 压入 progressive连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system快速换模系统regrinding再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人 roll forming machine辊轧成形roll forming machine辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler辊式矫直机rotary bender 卷弯成形机safety guard安全保护装置scrap cutter 废料切刀 scrap press 废料冲床seamless forging 无缝锻造separate 分别shave 崩砂 shear angle 剪角sheet loader 薄板装料机shot 单行程工作shrinkage fit 缩短配合 shut height 闭合高度sieve mesh 筛孔 sintering of sand铸砂烧贴slide balancer 滑动均衡器slug hole 逃料孔spin forming machine旋压成形机spotting 合模stack feeder 堆叠拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler拉伸矫直机strip feeder 料材送料装置stripping pressure弹出压力stroke 冲程 take out device取料装置toggle press 肘杆式压力机transfer 传递transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机 vibration feeder 振动送料机wiring press 嵌线卷边机线切割放电加工关系用语abnormal glow不规则辉光放电arc discharge 电弧放电belt 皮带centreless 没心chrome bronze 铭铜clearance angle 後角corner shear drop 直角压陷deflection 桡曲度discharge energy 放电能量dressing 修整dwell 保压flange 凸缘gap 缝隙graphite 石墨graphite contraction allowance电极减小余量graphite holder电极夹座hair crack 发裂horn 电极臂jump 跳刀magnetic base 磁性座master graphite 标准电极pipe graphite 管状电极pulse 脉冲rib working肋部加工roller electrode滚轮式电极rotary surface 旋转面shank 柄部sharp edge 锐角部tough bronze 韧铜traverse 摇臂tungsten bronze ?青铜waviness 波形起伏work 工件working allowance加工余量working dischard加工废料。

机械专业术语（英语）大全机械专业术语，中英文对照！阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation ; creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion 等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism 多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design 机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing角接触向心轴承angular contact radial bearing角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating径向基本额定静载荷basic static radial load tating 径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism 力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket ; sprocket-wheel ; sprocket gear ; chain wheel 联组V 带tight-up V belt联轴器coupling ; shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design ; design for environment马耳他机构Geneva wheel ; Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion ;wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator燃点spontaneous ignition热平衡heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference 设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift实际廓线cam profile十字滑块联轴器double slider coupling; Oldham‘s co upling 矢量vector输出功output work输出构件output link输出机构output mechanism输出力矩output torque输出轴output shaft输入构件input link数学模型mathematic model实际啮合线actual line of action双滑块机构double-slider mechanism, ellipsograph双曲柄机构double crank mechanism双曲面齿轮hyperboloid gear双头螺柱studs双万向联轴节constant-velocity (or double) universal joint 双摇杆机构double rocker mechanism双转块机构Oldham coupling双列轴承double row bearing双向推力轴承double-direction thrust bearing松边slack-side顺时针clockwise瞬心instantaneous center死点dead point四杆机构four-bar linkage速度velocity速度不均匀( 波动) 系数coefficient of speed fluctuation 速度波动speed fluctuation速度曲线velocity diagram速度瞬心instantaneous center of velocity塔轮step pulley踏板pedal台钳、虎钳vice太阳轮sun gear弹性滑动elasticity sliding motion弹性联轴器elastic coupling ; flexible coupling弹性套柱销联轴器rubber-cushioned sleeve bearing coupling 套筒sleeve梯形螺纹acme thread form特殊运动链special kinematic chain特性characteristics替代机构equivalent mechanism调节modulation, regulation调心滚子轴承self-aligning roller bearing调心球轴承self-aligning ball bearing调心轴承self-aligning bearing调速speed governing调速电动机adjustable speed motors调速系统speed control system调压调速variable voltage control调速器regulator, governor铁磁流体密封ferrofluid seal停车阶段stopping phase停歇dwell同步带synchronous belt同步带传动synchronous belt drive凸的，凸面体convex凸轮cam凸轮倒置机构inverse cam mechanism凸轮机构cam , cam mechanism凸轮廓线cam profile凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve凸缘联轴器flange coupling图册、图谱atlas图解法graphical method推程rise推力球轴承thrust ball bearing推力轴承thrust bearing退刀槽tool withdrawal groove退火anneal陀螺仪gyroscopeV 带V belt外力external force外圈outer ring外形尺寸boundary dimension万向联轴器Hooks coupling ; universal coupling 外齿轮external gear弯曲应力beading stress弯矩bending moment腕部wrist往复移动reciprocating motion往复式密封reciprocating seal网上设计on-net design, OND微动螺旋机构differential screw mechanism位移displacement位移曲线displacement diagram位姿pose , position and orientation稳定运转阶段steady motion period稳健设计robust design蜗杆worm蜗杆传动机构worm gearing蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear蜗杆形凸轮步进机构worm cam interval mechanism蜗杆旋向hands of worm蜗轮worm gear涡圈形盘簧power spring无级变速装置stepless speed changes devices无穷大infinite系杆crank arm, planet carrier现场平衡field balancing向心轴承radial bearing向心力centrifugal force相对速度relative velocity相对运动relative motion相对间隙relative gap象限quadrant橡皮泥plasticine细牙螺纹fine threads销pin消耗consumption小齿轮pinion小径minor diameter橡胶弹簧balata spring修正梯形加速度运动规律modified trapezoidal acceleration motion 修正正弦加速度运动规律modified sine acceleration motion斜齿圆柱齿轮helical gear斜键、钩头楔键taper key泄漏leakage谐波齿轮harmonic gear谐波传动harmonic driving谐波发生器harmonic generator斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio行星齿轮装置planetary transmission行星轮planet gear行星轮变速装置planetary speed changing devices行星轮系planetary gear train形封闭凸轮机构positive-drive (or form-closed) cam mechanism 虚拟现实virtual reality虚拟现实技术virtual reality technology, VRT虚拟现实设计virtual reality design, VRD虚约束redundant (or passive) constraint许用不平衡量allowable amount of unbalance许用压力角allowable pressure angle许用应力allowable stress; permissible stress悬臂结构cantilever structure悬臂梁cantilever beam循环功率流circulating power load旋转力矩running torque旋转式密封rotating seal旋转运动rotary motion选型type selection压力pressure压力中心center of pressure压缩机compressor压应力compressive stress压力角pressure angle牙嵌式联轴器jaw (teeth) positive-contact coupling雅可比矩阵Jacobi matrix摇杆rocker液力传动hydrodynamic drive液力耦合器hydraulic couplers液体弹簧liquid spring液压无级变速hydraulic stepless speed changes液压机构hydraulic mechanism一般化运动链generalized kinematic chain移动从动件reciprocating follower移动副prismatic pair, sliding pair移动关节prismatic joint移动凸轮wedge cam盈亏功increment or decrement work应力幅stress amplitude应力集中stress concentration应力集中系数factor of stress concentration应力图stress diagram应力—应变图stress-strain diagram优化设计optimal design油杯oil bottle油壶oil can油沟密封oily ditch seal有害阻力useless resistance有益阻力useful resistance有效拉力effective tension有效圆周力effective circle force有害阻力detrimental resistance余弦加速度运动cosine acceleration (or simple harmonic) motion 预紧力preload原动机primer mover圆带round belt圆带传动round belt drive圆弧齿厚circular thickness圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover原始机构original mechanism圆形齿轮circular gear圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair圆柱式凸轮步进运动机构barrel (cylindric) cam圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧cylindroid helical-coil compression spring圆柱凸轮cylindrical cam圆柱蜗杆cylindrical worm圆柱坐标操作器cylindrical coordinate manipulator圆锥螺旋扭转弹簧conoid helical-coil compression spring圆锥滚子tapered roller圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears圆锥角cone angle原动件driving link约束constraint约束条件constraint condition约束反力constraining force跃度jerk跃度曲线jerk diagram运动倒置kinematic inversion运动方案设计kinematic precept design运动分析kinematic analysis运动副kinematic pair运动构件moving link运动简图kinematic sketch运动链kinematic chain运动失真undercutting运动设计kinematic design运动周期cycle of motion运动综合kinematic synthesis运转不均匀系数coefficient of velocity fluctuation 运动粘度kenematic viscosity载荷load载荷—变形曲线load—deformation curve载荷—变形图load—deformation diagram窄V 带narrow V belt毡圈密封felt ring seal展成法generating张紧力tension张紧轮tension pulley振动vibration振动力矩shaking couple振动频率frequency of vibration振幅amplitude of vibration正切机构tangent mechanism正向运动学direct (forward) kinematics正弦机构sine generator, scotch yoke织布机loom正应力、法向应力normal stress制动器brake直齿圆柱齿轮spur gear直齿锥齿轮straight bevel gear直角三角形right triangle直角坐标操作器Cartesian coordinate manipulator 直径系数diametral quotient直径系列diameter series直廓环面蜗杆hindley worm直线运动linear motion直轴straight shaft质量mass质心center of mass执行构件executive link; working link质径积mass-radius product智能化设计intelligent design, ID中间平面mid-plane中心距center distance中心距变动center distance change中心轮central gear中径mean diameter终止啮合点final contact, end of contact周节pitch周期性速度波动periodic speed fluctuation周转轮系epicyclic gear train肘形机构toggle mechanism轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承高度bearing height轴承宽度bearing width轴承内径bearing bore diameter轴承寿命bearing life轴承套圈bearing ring轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile轴向当量动载荷dynamic equivalent axial load轴向当量静载荷static equivalent axial load轴向基本额定动载荷basic dynamic axial load rating 轴向基本额定静载荷basic static axial load rating轴向接触轴承axial contact bearing轴向平面axial plane轴向游隙axial internal clearance轴向载荷axial load轴向载荷系数axial load factor轴向分力axial thrust load主动件driving link主动齿轮driving gear主动带轮driving pulley转动导杆机构whitworth mechanism转动副revolute (turning) pair转速swiveling speed ; rotating speed转动关节revolute joint转轴revolving shaft转子rotor转子平衡balance of rotor装配条件assembly condition锥齿轮bevel gear锥顶common apex of cone锥距cone distance锥轮bevel pulley; bevel wheel锥齿轮的当量直齿轮equivalent spur gear of the bevel gear锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear子程序subroutine子机构sub-mechanism自动化automation自锁self-locking自锁条件condition of self-locking自由度degree of freedom, mobility总重合度total contact ratio总反力resultant force总效率combined efficiency; overall efficiency组成原理theory of constitution组合齿形composite tooth form组合安装stack mounting组合机构combined mechanism阻抗力resistance最大盈亏功maximum difference work between plus and minus work 纵向重合度overlap contact ratio纵坐标ordinate组合机构combined mechanism最少齿数minimum teeth number最小向径minimum radius作用力applied force坐标系coordinate frame机械专利翻译词汇三千个Assembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Electric screw driver 电动起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine 热熔机repair 修理operator 作业员QC 品管supervisor 课长ME 制造工程师cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. Inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试V oltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department 生产部门planning department 企划部QC Section 品管科stamping factory 冲压厂painting factory 烤漆厂molding factory 成型厂common equipment 常用设备uncoiler and straightener 整平机punching machine 冲床robot 机械手hydraulic machine 油压机lathe 车床planer 刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机staker=reviting machine 铆合机position 职务president 董事长general manager 总经理special assistant manager 特别助理factory director 厂长department director 部长deputy manager | =vice manager 副经理section supervisor 课长deputy section supervisor =vice section superisor 副课长group leader/supervisor 组长line supervisor 线长assistant manager 助理to move, to carry, to handle 搬运be put in storage 入库pack packing 包装to apply oil 擦油to file burr 锉毛刺final inspection 终检to connect material 接料to reverse material 翻料wet station 沾湿台Tiana 天那水cleaning cloth 抹布to load material 上料to unload material 卸料to return material/stock to 退料scraped |'skræpid| 报废scrape 刮;削deficient purchase 来料不良manufacture procedure 制造过程deficient manufacturing procedur 制造过程不良oxidation 氧化scratch 刮伤dents 压痕defective upsiding down 抽芽不良defective to staking 铆合不良embedded lump 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力education and training 教育与训练proposal improvement 提案改善spare parts=buffer 备件forklift 叉车trailer=long vehicle 拖板车compound die 合模die locker 锁模器pressure plate=plate pinch 压板bolt 螺栓name of a department 部门名称administration/general affairs dept 总务部automatic screwdriver 电动启子thickness gauge 厚薄规gauge(or jig) 治具power wire 电源线buzzle 蜂鸣器defective product label 不良标签identifying sheet list 标示单screwdriver holder 起子插座pedal 踩踏板stopper 阻挡器。

机械专业术语常用机械专业术语，了解掌握，不仅有助于业务的开展和进步，还能减少工作中的差错。

一般而言，经过归纳整理，机械行业通用的专业术语包括以下几个方面。

(1)计划指令控制(PMC)例如：提出一套新产品生产计划、物料需求计划、能力需求计划、设备维修计划等;或者提出一套调整原材料供应量的措施计划，并将它们发送到各个分厂。

(2)机器作业指令(CMP)例如：检查一下各个电动机的转速是否在规定的范围内;打开清扫装置，清除其上的尘土，关闭一下冷却水;“查看”一下主轴箱润滑油油位情况等。

(3)工序控制(SSC)例如：加工一批零件时，一个车间应根据工艺文件规定的加工顺序对每一道工序严格控制，防止出现“错、漏”现象。

(4)工艺文件(TD)例如：编写一份加工某种零件的工艺文件。

(5)标准作业指导书(StandardWorkout)例如：编制一份以某种产品为对象的标准作业指导书。

(6)工具和夹具(对刀具和辅具)例如：为一批即将加工的零件配备一套合适的工装。

(7)状态管理(SCM)例如：查看每个机床、车间和工厂里所使用的生产设备是否处于正常运行状态，并做好记录;关注某个主要生产设备的磨损情况并采取相应的维修保养措施。

(8)物流例如：审查库存信息并及时补充缺货情况，或根据库存情况确定订货数量。

(9)产品质量计划(PDC)例如：实施某个零件或一批零件的抽样检验计划，计划可从设计阶段开始。

用计划指令控制，可以保证各生产车间按照计划的进度组织生产;用作业指令控制，可以保证各生产车间正常、均衡地完成各项作业，避免各种浪费，提高劳动效率。

用工序控制，可以使零件在加工过程中不会出现“错、漏”，即便是加工过程中出现了“错、漏”也可以根据工序控制，予以纠正。

例如在外协厂家加工过程中，当该厂家没有按计划加工，或者加工工艺不达标，造成零件报废时，那么该批零件就需要返回给总装车间重新加工。

(10)操作控制(OOM)例如：执行自动上下料系统时，确认手动或自动系统已正确安装后才开始加工;确认物料状态符合要求后才放料;确认刀具和夹具都处于正确状态后才进行加工。

机械行业专业术语1 ．压模制造心die casting )低压铸造．通常将液态锌注人机加工制成的模具。

2 ．电火花加工（electrodischarge machining . EDM )用电极使硬金属表面熔化并蒸发。

通常用于高硬度金属的低速加工。

3 . G 指令（G-codes )标准的低端数控编程代码·用于实现某种运动．如Gl-用于实现直线进给。

4 ．注射成形（injection molding )将粘状聚合物（或金属溶液―译者注）挤压至模具空腔而形成零件。

5 ．三维印刷中的喷墨打印（ink-jet printing in3-D )一种决速成形法．先将一层粉末状材料铺平．然后根据CAD 模型有选择性的向上喷涂一层粘接材料．再将喷涂区域进行硬化。

6 ．熔模铸造（investment casting）英文单词investment （投入）用来形容该铸造方法意在将时间与金钱投人到一层陶瓷走人上．滚壳不汪铸件弓之；几珍波刊的‘：亥方乙去l 护湘不上成壳沐的了于哎可月几种丁造夫蜡涛造和陶瓷漠：们选是最否巡采用的铸漠涛造＿7 ．分层实体制造｛lanlinated , . ! lioct ; 11 。

，dolin 只．LO 入I ) 一种决速成形法它用激光切刽一叠纸的表层，并与下面切好的一层由特种胶枯结起来咬原L ( ) M 机器制造商Hehsy 、以及一些权威作者·如文献泣2 。

」和二21 」的作者．使用laminated object manufacturing ―译者注。

）8 ．研磨与抛光（lapping and polishing )用于已经加工好的表面的最后抛光与平滑。

表面研磨一般是采用带有细至0 . 25 拼m 直径的金刚石平板来完成。

9 ．机加工（machinin 只、较通用的一种通过车未或能宋完成的制造方去它从实忧块去除切屑物．此氛不同于锻压、银金加工及焊接工艺。

10 . M 指令（M 一codes )数控程字中用于与：．刃．二轴运动无关的指令列如．M6 ―用于实现换刀11 ．近净形制造（nea 卜net shape 、指银金加工、锻压或烧结（如粉末冶金―译者注）等工艺它们能几乎直接获得最后零件（只需要少量机加工即可获得最后零件夕。

机械行业常用术语英文对照组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌OOBA开箱检查fit together组装在一起fasten锁紧(螺丝)fixture 夹具(治具)pallet栈板barcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cosmetic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch镑、英寸EMI gasket导电条front plate前板rear plate后板chassis基座bezel panel面板power button电源按键reset button重置键Hi-pot test of SPS高源高压测试V oltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource department 人力资源部production department生产部门planning department企划部QC Section品管科stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床robot机械手hydraulic machine油压机lathe车床planer |'plein |刨床miller铣床grinder磨床driller钻床linear cutting线切割electrical sparkle电火花welder电焊机staker=reviting machine铆合机position职务president董事长general manager总经理special assistant manager特助factory director厂长department director部长deputy manager | =vice manager副理section supervisor课长deputy section supervisor =vice section superisor副课长group leader/supervisor组长line supervisor线长assistant manager助理to move, to carry, to handle搬运be put in storage入库pack packing包装to apply oil擦油to file burr 锉毛刺final inspection终检to connect material接料to reverse material 翻料wet station沾湿台Tiana天那水cleaning cloth抹布to load material上料to unload material卸料to return material/stock to退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei n|氧化scratch刮伤dents压痕defective upsiding down抽芽不良defective to staking铆合不良embedded lump镶块feeding is not in place送料不到位stamping-missing漏冲production capacity生产力education and training教育与训练proposal improvement提案改善spare parts=buffer备件forklift叉车trailer=long vehicle拖板车compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规gauge(or jig)治具power wire电源线buzzle蜂鸣器defective product label不良标签identifying sheet list标示单screwdriver holder起子插座pedal踩踏板stopper阻挡器flow board流水板hydraulic handjack油压板车forklift叉车pallet栈板glove(s)手套glove(s) with exposed fingers割手套thumb大拇指forefinger食指midfinger中指ring finger无名指little finger小指band-aid创可贴iudustrial alcohol工业酒精alcohol container沾湿台head of screwdriver起子头sweeper扫把mop拖把vaccum cleaner吸尘器rag 抹布garbage container灰箕garbage can垃圾箱garbage bag垃圾袋chain链条jack升降机production line流水线chain链条槽magnetizer加磁器lamp holder灯架to mop the floor拖地to clean the floor扫地to clean a table擦桌子air pipe 气管packaging tool打包机packaging打包missing part漏件wrong part错件excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小)cosmetic defect外观不良slipped screwhead/slippery screw head 螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属)flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大grease/oil stains油污inclusion杂质painting peel off脏污shrinking/shrinkage缩水mixed color杂色scratch划伤poor processing 制程不良poor incoming part事件不良fold of pakaging belt打包带折皱painting make-up补漆discoloration羿色water spots水渍polishing/surface processing表面处理exposed metal/bare metal金属裸露lack of painting烤漆不到位safety安全quality品质delivery deadline交货期cost成本engineering工程die repair模修enterprise plan = enterprise expansion projects企划QC品管die worker模工production, to produce生产equipment设备to start a press开机stop/switch off a press关机classification整理regulation整顿cleanness清扫conservation清洁culture教养qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料board看板feeder送料机sliding rack滑料架defective product box不良品箱die change 换模to fix a die装模to take apart a die拆模to repair a die修模packing material包材basket蝴蝶竺plastic basket胶筐isolating plate baffle plate; barricade隔板carton box纸箱to pull and stretch拉深to put material in place, to cut material, to input落料to impose lines压线to compress, compressing压缩character die字模to feed, feeding送料transportation运输(be)qualfied, up to grade合格not up to grade, not qualified不合格material change, stock change材料变更feature change 特性变更evaluation评估prepare for, make preparations for 准备parameters参数rotating speed, revolution转速manufacture management制造管理abnormal handling异常处理production unit生产单位lots of production生产批量steel plate钢板roll material卷料manufacture procedure制程operation procedure作业流程to revise, modify修订to switch over to, switch---to throw--over switching over切换engineering, project difficulty工程瓶颈stage die工程模automation自动化to stake, staking, reviting铆合add lubricating oil加润滑油shut die架模shut height of a die架模高度analog-mode device类模器die lifter举模器argon welding氩焊vocabulary for stamping冲压常词汇stamping, press冲压punch press, dieing out press冲床uncoiler & strainghtener 整平机feeder送料机rack, shelf, stack料架cylinder油缸robot机械手taker取料机conveyer belt输送带transmission rack输送架top stop上死点bottom stop下死点one stroke一行程inch寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, blockstop 定位块reset复位smoothly顺利dent压痕scratch刮伤deformation变形filings铁削to draw holes抽孔inquiry, search for查寻to stock, storage, in stock库存receive领取approval examine and verify审核processing, to process加工delivery, to deliver 交货to return delivenry to.to send delinery backto retrn of goods退货registration登记registration card登记卡to control管制to put forward and hand in提报safe stock安全库存acceptance = receive验收to notice通知application form for purchase请购单consume, consumption消耗to fill in填写abrasion磨损reverse angle = chamfer倒角character die字模to collect, to gather收集failure, trouble故障statistics统计demand and supply需求career card履历卡to take apart a die卸下模具to load a die装上模具to tight a bolt拧紧螺栓to looser a bolt拧松螺栓to move away a die plate移走模板easily damaged parts易损件standard parts标准件breaking.(be)broken,(be)cracked 断裂to lubricate润滑common vocabulary for die engineering模具工程常用词汇die 模具figure file, chart file图档cutting die, blanking die冲裁模progressive die, follow (-on)die连续模compound die复合模punched hole冲孔panel board镶块to cutedges=side cut=side scrap切边to bending折弯to pull, to stretch拉伸Line streching, line pulling线拉伸engraving, to engrave刻印upsiding down edges翻边to stake铆合designing, to design设计design modification设计变化die block模块folded block折弯块sliding block滑块location pin定位销lifting pin顶料销die plate, front board模板padding block垫块stepping bar垫条upper die base上模座lower die base下模座upper supporting blank上承板upper padding plate blank上垫板spare dies模具备品spring 弹簧bolt螺栓document folder文件夹file folder资料夹to put file in order整理资料spare tools location手工备品仓first count初盘人first check初盘复棹人second count 复盘人second check复盘复核人equipment设备waste materials废料work in progress product在制品casing = containerazation装箱quantity of physical invetory second count 复盘点数量quantity of customs count会计师盘,点数量the first page第一联filed by accounting department for reference会计部存查end-user/using unit(department)使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name单据名称This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)本表请与盘点清册一起送会计部－(NHK厂区送财会部)Application status records of year-end physical inventory List andphysical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate电镀mold成型material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品incoming material to be inspected进货待验description品名steel/rolled steel钢材material statistics sheet物料统计明细表meeting minutes会议记录meeting type 会别distribution department分发单位location地点chairman主席present members出席人员subject主题conclusion结论decision items决议事项responsible department负责单位pre-fixed finishing date预定完成日approved by / checked by / prepared by 核准/审核/承办PCE assembly production schedule sheetPCE组装厂生产排配表model机锺work order工令revision版次remark备注production control confirmation生产确认checked by初审approved by核准department部门stock age analysis sheet库存货龄分析表on-hand inventory现有库存available material良品可使用obsolete material良品已呆滞to be inspected or reworked待验或重工total合计cause description原因说明part number/ P/N 料号type形态item/group/class类别quality品质prepared by制表notes说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory盘点数量physical count quantity帐面数量difference quantity差异量cause analysis原因分析raw materials原料materials物料finished product成品semi-finished product半成品packing materials包材good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品disposed goods处理品warehouse/hub仓库on way location在途仓oversea location海外仓spare parts physical inventory list备品盘点清单spare molds location模具备品仓skid/pallet栈板tox machine自铆机wire EDM线割EDM放电机coil stock卷料sheet stock片料tolerance工差score=groove压线cam block滑块pilot导正筒trim剪外边pierce剪内边drag form压锻差pocket for the punch head挂钩槽slug hole废料孔feature die公母模expansion dwg展开图radius半径shim(wedge)楔子torch-flame cut火焰切割set screw止付螺丝form block折刀stop pin定位销round pierce punch=die button圆冲子shape punch=die insert异形子stock locater block定位块under cut=scrap chopper清角active plate活动板baffle plate挡块cover plate盖板male die公模female die母模groove punch压线冲子air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套insert 入块club car高尔夫球车capability能力parameter参数factor系数phosphate皮膜化成viscosity涂料粘度alkalidipping脱脂main manifold主集流脉bezel斜视规blanking穿落模dejecting顶固模demagnetization去磁;消磁high-speed transmission高速传递heat dissipation热传rack上料degrease脱脂rinse水洗alkaline etch龄咬desmut剥黑膜D.I. rinse纯水次Chromate铬酸处理Anodize阳性处理seal封孔revision版次part number/P/N料号good products良品scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条码flow chart流程表单assembly组装stamping冲压molding成型spare parts=buffer备品coordinate座标dismantle the die折模auxiliary fuction辅助功能poly-line多义线heater band 加热片thermocouple热电偶sand blasting喷沙grit 砂砾derusting machine除锈机degate打浇口dryer烘干机induction感应induction light感应光response=reaction=interaction感应ram连杆edge finder巡边器concave凸convex凹short射料不足nick缺口speck瑕??shine亮班splay 银纹gas mark焦痕delamination起鳞cold slug冷块blush 导色gouge沟槽;凿槽satin texture段面咬花witness line证示线patent专利grit沙砾granule=peuet=grain细粒grit maker抽粒机cushion缓冲magnalium镁铝合金magnesium镁金metal plate钣金lathe车mill锉plane刨grind磨drill铝boring镗blinster气泡fillet镶;嵌边through-hole form通孔形式voller pin formality滚针形式cam driver铡楔shank摸柄crank shaft曲柄轴augular offset角度偏差velocity速度production tempo生产进度现状torque扭矩spline=the multiple keys花键quenching淬火tempering回火annealing退火carbonization碳化alloy合金tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导liaison联络单volatile挥发性resistance电阻ion离子titrator滴定仪beacon警示灯coolant冷却液crusher破碎机模具工程类plain die简易模pierce die冲孔模forming die成型模progressive die连续模gang dies复合模shearing die剪边模riveting die铆合模pierce冲孔forming成型(抽凸,冲凸) draw hole抽孔bending折弯trim切边emboss凸点dome凸圆semi-shearing半剪stamp mark冲记号deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平reel stretch卷圆压平groove压线blanking下料stamp letter冲字(料号) shearing剪断tick-mark nearside正面压印tick-mark farside反面压印冲压名称类extension dwg展开图procedure dwg工程图die structure dwg模具结构图material材质material thickness料片厚度factor系数upward向上downward向下press specification冲床规格die height range适用模高die height闭模高度burr毛边gap间隙weight重量total wt.总重量punch wt.上模重量五金零件类inner guiding post内导柱inner hexagon screw内六角螺钉dowel pin固定销coil spring弹簧lifter pin顶料销eq-height sleeves=spool等高套筒pin销lifter guide pin浮升导料销guide pin导正销wire spring圆线弹簧outer guiding post外导柱stop screw止付螺丝located pin定位销outer bush外导套模板类top plate上托板（顶板）top block上垫脚punch set上模座punch pad上垫板punch holder上夹板stripper pad脱料背板up stripper上脱料板male die公模(凸模)feature die公母模female die母模(凹模)upper plate上模板lower plate下模板die pad下垫板die holder下夹板die set下模座bottom block下垫脚bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板inner stripper内脱料板lower stripper下脱料板零件类punch冲头insert入块(嵌入件)deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子special shape punch异形冲子bending block折刀roller滚轴baffle plate挡块located block定位块supporting block for location定位支承块air cushion plate气垫板air-cushion eject-rod气垫顶杆trimming punch切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子reel-stretch punch卷圆压平冲子guide plate定位板sliding block滑块sliding dowel block滑块固定块active plate活动板lower sliding plate下滑块板upper holder block上压块upper mid plate上中间板spring box弹簧箱spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套cover plate盖板guide pad导料块塑件&模具相关英文compre sion molding压缩成型flash mold溢流式模具plsitive mold挤压式模具split mold分割式模具cavity型控母模core模心公模taper锥拔leather cloak仿皮革shiver饰纹flow mark流痕welding mark溶合痕post screw insert螺纹套筒埋值self tapping screw自攻螺丝striper plate脱料板piston活塞cylinder汽缸套chip细碎物handle mold手持式模具移转成型用模具encapsulation molding低压封装成型射出成型用模具two plate两极式（模具）well type蓄料井insulated runner绝缘浇道方式hot runner热浇道runner plat浇道模块valve gate阀门浇口band heater环带状的电热器spindle阀针spear head刨尖头slag well冷料井cold slag冷料渣air vent排气道h=0.02~0.05mmw=3.2mmL=3~5mm welding line熔合痕eject pin顶出针knock pin顶出销return pin回位销反顶针sleave套筒stripper plate脱料板insert core放置入子runner stripper plate浇道脱料板guide pin导销eject rod (bar)（成型机）顶业捧subzero深冷处理three plate三极式模具runner system浇道系统stress crack应力电裂orientation定向sprue gate射料浇口，直浇口nozzle射嘴sprue lock pin料头钩销(拉料杆)slag well冷料井side gate侧浇口edge gate侧缘浇口tab gate搭接浇口film gate薄膜浇口flash gate闸门浇口slit gate缝隙浇口fan gate扇形浇口dish gate因盘形浇口H=F=1/2t~1/5tT=2.5~3.5mmdiaphragm gate隔膜浇口ring gate环形浇口subarine gate潜入式浇口tunnel gate隧道式浇口pin gate针点浇口Φ0.8~1.0mmRunner less无浇道(sprue less)无射料管方式long nozzle延长喷嘴方式sprue浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control 制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality 合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8项回复内容FA final audit 最後一次稽核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report 百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM T otal Quality Management全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice品质改善活动ADM Absolute DimensionMeasuremat 全尺寸测量QT Quality Target 品质目标7QCT ools 7 Quality Controll T ools品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商)ECO Engineering Change Order 工程改动要求(客户)PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-ManufactC-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课) PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States of America 美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-Only Memory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CA V Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3CComputer,Commumcation,Consumer electronic's 消费性电子5WIHWhen,Where,Who,What,Why,How to 5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect 高磁测试FMI Frequency Modulatim Inspect 高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture 工业标准体制结构MCA Micro Channel Architecture 微通道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module 双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes 失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance全面生产保养MRP Material Requiremcnt Planning物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material Condition MMS Maximum Material Size LMC Least Material Condition LMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shell casting 壳模铸造foam forming ?泡成形sinter forging烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loading shoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold活动式模具clod hobbing 冷挤压制模louveringdie 百叶窗冲切模composite dies 复合模具manifolddie 分歧管模具counter punch 反凸模modular mold组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bendingdie 双折冷弯模具extrusion die 挤出模palletizing die叠层模family mold 反套制品模具plastermold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die压紧模fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold 单腔模具solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoketype die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁)cavity retainer plate 模穴托板centerpin 中心梢clamping block 锁定块coil spring螺旋弹簧cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate 盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve 顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧? goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶?冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套inner plunger 内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar 脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶?lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locatingring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block歧管档块master plate 靠模样板match plate 分型板mold base 塑胶模座mold clamp 铸模紧固夹mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件parallel block 平行垫块paring line 分模线parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导?pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch 冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin 嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate 环型浇口roller 滚筒runner 流道runner ejector set 流道顶出器runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片shoe 模座之上下模板shoot 流道shoulder bolt 肩部螺丝skeleton 骨架。

机械行业专业术语机械行业是指以机械工程技术为基础，涉及到机械制造、机械设计、机械维修等方面的行业。

在机械行业中，有许多专业术语被广泛使用，这些术语是机械工程师和从业者之间交流的基础。

下面是一些常见的机械行业专业术语，以帮助读者更好地理解和使用这些术语。

1. CADCAD是计算机辅助设计（Computer-Aided Design）的缩写，是一种使用计算机技术来辅助进行设计的工具。

在机械行业中，CAD主要用于绘制和设计机械零件、装配图和工程图纸。

通过CAD软件，设计师可以快速方便地进行设计、修改和优化。

2. CAMCAM是计算机辅助制造（Computer-Aided Manufacturing）的缩写，是利用计算机技术来辅助制造和加工的工具。

在机械行业中，CAM主要用于生成刀具路径、控制机器等，帮助实现机械产品的自动化生产和加工。

3. CNCCNC是计算机数控（Computer Numerical Control）的缩写，是一种利用计算机进行指令控制的数控系统。

在机械行业中，CNC常用于机床的控制，通过输入程序指令来实现精确的切削、钻孔、铣削等操作。

4. 模具模具是制造工业中常用的工装，用于生产产品的成型、复制和加工。

在机械行业中，模具被广泛应用于塑料制品、金属制品等的生产过程中。

模具可以通过CNC技术进行设计和加工，以实现高精度的产品加工。

传感器是一种用于检测和感知物理量和物质的装置。

在机械行业中，传感器常用于检测温度、压力、速度等各种物理量，并将其转化为电信号输出。

通过传感器的使用，可以实现机械设备的自动化控制和监测。

6. 动力系统动力系统是指机械设备中用于提供动力的系统。

在机械行业中，常见的动力系统包括发动机、电机、液压系统等。

通过动力系统的使用，机械设备可以实现运动、驱动和动力传输。

7. 机械强度机械强度是指机械材料或机械构件在受力作用下的抗压、抗拉、抗剪等能力。

在机械行业中，机械强度是一个重要的设计指标，用于评估机械材料的质量和可靠性。

4针接头4-pin connector5针接头5-pin connectorDC-DC转换器dc-dc voltage transformer E型减震器e-shock absorberGPS卫星定位跟踪器gpsKD键kick down keyO形挡圈o retainerO形圈o-ringO形圈接头o-ring connectorO形塞o ring plugT形套t-sleeveT型抱箍t-clampU形钩clevisU形夹clevisU形螺栓u-boltU形圈u-ringU型管箍u-clampV型管夹v-clampV型环v-ringYX形密封圈yx-ringY形密封圈y-ring安全标志safety sign安全锤hammer安全锤座hammer seat安全带seat belt安全阀safety valve安全滤芯safety filter element安全装置safety devices安装板mounting plate安装板组件mtg gp安装座mount-tube form按钮button按钮key按钮knob凹槽recess把手handhold白炽灯incandescent lamp摆臂swing arm摆动盘swing plate摆动支架swing bracket摆动轴swing bearing摆轮balance wheel摆线齿轮cycl6idat gear扳手spanner扳手wrench搬扭开关toggle switch板board板plate板弹簧flat spring板簧blade spring板组件plate gp半圆键woodruff key半圆头接头件button connector半圆头螺钉button head screw半圆头铆钉button head rivet半圆头塞button plug保持环keep-ring保护垫sheet保护架guard as保护塞protective plug保护罩canopy as保护装置protector保险fuse保险盒fuse box保险盒铭牌fuse box nameplate保险丝fuse保险丝座fuse seat保养指示灯service indicator报警开关alert switch报警器及压力开关alarm & pressure switch 报警器组alarm unit报警指示灯alert indicator抱叉logging fork clamp杯座cup holder备选仪表spare gauge备用环backup ring备用开关spare switch泵pump泵调节器pump regulator泵法兰pump flange泵盖pump cover泵缸pump cylinder泵壳体pump housing泵轮pump gear泵体pump body泵吸油管路pump oil suction hose 泵轴shaft-pump泵座pump seat壁灯wall lamp臂arm扁钢flat bar变径管reducer变径接头reducer union变矩器torque converter变矩器-变速箱安装 torque convert & tansmission mounting 变矩器-变速箱管路 torque convert & tansmission lines变矩器机芯torque converter core变矩器冷却系统torque converter cooling system变速泵shift pump变速操纵工作装置shift contro implement变速操纵手柄gearshift knob变速操纵手柄shift control lever变速操纵线路power shift control lines变速操纵线束power shift control harness变速调档系统gear shift system变速控制阀shift control valve变速排当旋钮gearshift knob变速箱gear-box变速箱transmission变速箱transmission case变速箱护板transmission guard变速箱系统transmission ar变速油压表transmission oil pressure gauge变压器transformer标牌plate-ident标牌tag表面密封衬套face seal sleeve表面密封螺母face seal nut丙酮acetone玻璃glass玻璃窗橡胶条glazing rubber薄垫片shim补偿垫圈shim补偿阀valve gp-make up补偿阀组件make up valve gp材料单bill of materials操纵杆joystick操纵盒control unit操纵机构operating mechanism操纵台架operator's platform操纵台架安装组件mtg gp-platform操作把手knob-gearshift操作模式切换管路operartion mode changed piping槽钢channel槽钢件channel as槽轮groove pulley槽凸轮groove cam槽销slot pin侧板cutting side wall侧卸油缸管路 side dump cylinder lines 侧翼螺拴shoulder bolt侧罩side hood测试管路test lines叉fork叉臂yoke叉车forklift叉架yoke-crank叉形杆头yoke rod end插板flashboard插头insert插销latch插座plug插座receptacle差速器differential差速器盖differential cover差速器壳case-diff差速器托架differential carrier差速器轴diff shaft差速器锥齿轮gear-diff bevel柴油标志diesel oil sign柴油机diesel柴油箱diesel oil tank产品铭牌product nameplate铲刀摆动油缸blade swing cylinder铲刀举升油缸blade lift cylinder铲斗bucket铲斗定位系统bucket auto control system 铲斗定位装置kickout gp铲斗滑阀bucket spool铲斗铰轴bucket pivot铲斗连杆bucket linkage铲斗油缸bucket cylinder铲斗油缸管路bucket cylinder lines铲斗组件bucket gp长半轴half shaft长齿套long tip长齿套组件long tip gp长齿套组件tip gp-long车架frame车架固定杆link gp-lock车速表speedo车载冰箱icebox沉淀杯sediment collector沉头螺钉sunk screw衬板liner衬垫liner衬套bushing衬套sleeve齿轮gear齿轮泵gear pump齿轮泵盖cover齿轮传动gear drive齿轮环ring gear齿轮减速装置mechanical reduction gear 齿轮马达gear motor齿轮箱gear case齿轮油gear oil齿轮轴gear shaft齿条rack充电指示灯charge indicator充液阀charge valve除霜装置defroster除雪机构snow plow mechanism储液罐tank receiver触杆filler neck触头contact传动系统transmission system传动箱transmission box传动油冷却管路lines gp-tc clr传动油滤油器filler gp-pt oil传动轴drive shaft传动轴transmission shaft传感器sensor窗window窗钩catch窗帘curtain窗主体basic window gp窗主体window gp-basic窗组件window gp吹风窗louver锤子hammer唇形密封圈lip type seal磁力盘magnetic plate磁铁magnet磁铁托块holder-magnet磁性螺塞plug-magc o ring从动齿轮driven gear从动轴driven shaft粗滤芯pre-filter淬硬垫圈washer-hard大灯head lamp大螺旋锥齿轮crown wheel带belt带帽螺栓nut bolt单相交流发电机single-phase alternator 单向阀check valve弹簧spring弹簧垫圈spring washer弹簧盖spring cover弹簧圈spring ring弹簧轴套spring sleeve弹簧座spring seat弹性挡圈retaining ring弹性螺母nut as-spring弹性销spring pin挡板plate-retainer挡风板baffle挡风玻璃windsheild挡风玻璃雨刮windshield wiper挡环blocking ring挡脚板foot barrier挡泥板fender挡圈check ring挡圈retainer挡圈snap ring挡油盖oil retainer挡雨板rain sheild刀cutter刀板blade刀板组件blade gp导杆guide bar导流板baffle导流管baffle tube导轮leading wheel导轮座stator base导入圈boot retainer导向带oriented strip导向阀guide valve导向辊子guide roller导向环guide ring导向环oriented ring导向螺杆guide bolt导向套oriented bushing导向套oriented seelve导向销guide pin导向轴件shaft as-pivot导座guide-valve倒车报警继电器backup alarm relay倒车报警器backup alarm倒车灯backup light倒车蜂鸣器reversing buzzer倒档内齿圈reverse inner gear ring 倒档行星架reverse planet carrier 倒档行星轴reverse planet shaft灯盖light cap灯系统light system灯箱light box灯支架light bracket灯组件lamp gp-dome灯组件lighting gp灯组件lighting group底板bottom board底板bottom plate底板floorplate底板plate-bottom底壳pan-filter底盘chassis底盘系统chassis ar底座bottom case底座板base plate地板floor plate地板垫floor mat地板架floor bracket点烟器lighter电池battery电磁传感器electromagnetic sensor电磁阀solenoid valve电磁离合器magnetic-particle clutch 电磁水阀solenoid water valve电磁铁coil as-w/plug电动泵electric pump电动机electromotor电动交流发电机motor alternator电动举升机构electrical lifting device 电控箱electronic control unit 电缆cable电缆扎cable strap电缆柱wiring harness电铃endbell电瓶battery电瓶危险标志battery warning sign电瓶线路组件battery wiring gp电瓶箱battery case电气系统electric system电气元件electric component电容器capacitor电刷brush电刷散件brush kit电刷散件马达brush kit motor电锁electric lock电线wire电线组件wiring gp电压/小时复合表voltage/service meter 电压表voltmeter电眼hydrometer电源power supply电源安全标志power safety sign电源插座socket电源开关标志power switch sign电源总开关main power switch电子放大器amplifier电子燃油喷射线路fuel injection wire 电子元件electronic component 电阻resistance电阻resistor电阻线圈resistance coil垫块pad垫片gasket垫片gasket-baffle垫片packing piece垫片retaimer垫片spacer垫圈washer吊钩hook吊钩附属装置hook attachment调节阀regulating valve调节器adjuster调压阀press regulator调整垫圈shim ring调整螺钉adjusting screw调整螺母adjusting nut调整螺塞adjusting plug调整螺栓adjusting bolt叠板簧1aminated spring碟形弹簧spring-disk蝶形阀butterfly valve蝶形螺母butterfly nut钉nail顶板plate-top顶保护网topguard net顶衬head liner顶灯dome light顶灯安装板dome light plate顶灯线路dome light wires顶灯线束dome light harness顶端top end顶推梁beam push顶罩hood as定距垫圈spacing washer定距片fixed distance piece定位销location pin定位针塞plug定子stator动臂arm动臂标贴arm sign动臂举升机构armrest lift mechanism动臂举升限位装置kickout动臂控制管路ride control lines动臂液压缸arm cylinder动臂油缸arm cylinder动臂油缸管路 arm cyliner lines动力传动系统power train动力系统power system斗边齿side tooth斗齿bucket tooth斗齿套tooth adapter斗齿销tooth pin斗齿组件tooth gp斗杆staff堵头plug端垫end shim端垫shim端螺栓terminal bolt端子terminal断电开关breaker断流阀shutoff valve断路器breaker断油阀fuel shut-off valve对开螺母split nut对偶钢片steel sheet多路换向阀multi-way diverter valve 多片式摩擦离合器multi disk clutch多头螺纹multiple threads多爪夹具multi-claw grab二极管diode二极管组件diode component发电机alternator发动机engine发动机安装engine mounting ar发动机报警指示灯engine alert indicator发动机风扇engine fan发动机盖engine hood发动机缸头engine cylinder headengine coolant level alert indicator 发动机冷却水位报警指示发动机冷却水温表engine coolant temperature gauge发动机曲轴箱engine crankcase发动机润滑油油位engine lubricant level发动机室engine room发动机水温表engine coolant temperature gauge发动机水温传感器engine coolant temperature sensor发动机位置传感器engine position sensor（eps）发动机系统engine system发动机油温表engine oil temperature gauge发动机油压报警指示灯engine oil pressure alert indicator 发动机油压传感器pressure sensor发动机罩engine hood发动机罩举升开关hood lift switch发动机转速计engine tachometer阀valve阀板duct plate阀弹簧valve spring阀端valve end阀盖valve cap阀杆stem-valve阀杆valve rod阀杆导向环piston guide ring阀管valve lines阀簧valve ring阀簧抵座销valve lock阀块valve block阀帽bonnet阀门gate阀门vane阀门散件vane kt阀套valve sleeve阀体block阀体valve body阀体组件valve body gp阀芯valve core阀主体basic valve gp阀主体valve gp-basic-a阀柱spool阀组valve gp-basic阀组件valve gp-air bsc阀座clack seat阀座seat-pilot阀座valve seat法兰flange法兰安装flange mounting法兰钢管flange tube法兰接头flange connector法兰块flange block法兰连接flange connection法兰面螺母flanged nut法兰面螺母nut-flanged法兰面螺栓bolt-special法兰盘flange plate法兰锁紧螺母flange locknut法兰头flanged head法兰罩flange cover法兰支座flange bracket翻斗阀杆stem-titl凡士林vaseline反光标贴glisten sign反馈连杆feedback level反馈销feedback pin方齿牙嵌离合器square jaw clutch方钢quadrant iron方颈螺栓bolt-carriage方颈螺栓carriage bolt方框图block diagram方头螺丝square head set screw方向机柱steering column方向盘steering wheel方向盘whee-hand steer方形键square key防尘盖cover-dust防尘盖dust cover防尘帽dust cap防尘圈dust ring防尘罩dust cover防滚翻装置rollover protective structure（rops）防护板protection plate防护盖cover-protective防护杆protection rod防护圈grommet防护套lag防护罩protection cap防护罩shield防护装置guard防滑扣anticreep防滑踏板anti-slip plate防滑条cleat防落物装置fops防磨底板anti-abrasion plate防热盖heat shield防水螺母bulkhead nut防水罩waterproof cover防松垫圈thrust washer防松螺母check nut防松螺母lock nut防松螺栓bolt-lock防烫伤标志 scald-proof sign防锈剂antirust放气嘴座relief seat放泄阀支座discharge valve support 放油阀体body-drain valve放油阀体drain valve body放油管路drain line放油螺塞drain plug放油装置oil drain assem.飞轮flywheel分泵secondary pump分配阀control valve分配阀杆control valve rod分配阀管路control valve lines分配器板controller plate风机blower风机壳blower housing风扇fan风扇垫fan spacer风扇法兰flange风扇马达管路fan motor lines风扇皮带fan belt风扇驱动马达motor风扇扇页fan blades风扇液压马达motor风扇罩fan guard风扇轴壳fan shaft house风扇装置fan as封盖sealing cap蜂鸣器buzzer扶手handrail扶手箱支架handrail bracket扶手压板handrail plate扶梯ladder氟里昂freon浮动密封floating seal浮动密封套floating seal bushing 辐板齿轮web wheel辅助阀体assistant valve body辅助锁定阀assistant lock valve辅助制动器secondary brake负极开关disconnect switch负载吊钩load hook附件attachment附属支座attachment bracket附属装置attachment附属装置工作管路option pipe复曲面密封环ring-sealing副车架subsidiary frame副水箱reservior盖cap盖cap-tank filler盖cover盖cover-emblem盖板cover plate盖板cover-bezel盖组件cover as杆bar杆rod杆(右)rod-rh杆(左)rod-lh杆头head stem杆头rodend感应传感器induct. transmitter感应交流发电机induction alternator刚性桥rigid axle缸盖crown缸盖head缸夹cylinder retaining clamp 缸套cylinder bushing缸体cylinder as缸体弹簧cylinder spring缸头体cap as钢板steel plate钢管steel tube钢管法兰tube flange钢球steel ball钢球steel sphere钢球单向阀ball check valve钢丝绳steel cable钢丝绳wire cable钢索wire rope钢套steel sleeve杠杆bell crank高压电源high voltage power supply格栅加热器grid heater格栅加热器电缆heater cable隔板baffle隔板baffle-cap隔板clapboard隔板screen sheet隔板接头spacer connector隔离环snap ring隔离环spacer ring隔盘partition隔热板firewall隔热板heat insulation plate 隔热板insulation隔热板组件firewall as隔音sound insulation隔音板sound insulation board 隔音棉sound insulation sponge 隔音组件suppression gp隔音组件suppression gp-b工具包kit工具箱tool kit工字梁h-beam工作泵working pump工作泵管路pump line工作灯work light工作灯继电器work light relay工作灯开关work light switch工作规程operation procedure工作台bench工作台operation plat form工作台work bench工作液压系统hydraulic system工作液压系统管路hydraulic system lines 工作油液working oil工作装置系统working device system 功能面板instrument panel供油泵feed-pump供油泵fuel pump钩头斜键gib-head taper key钩形螺栓hook bolt箍圈clamp.bracket鼓轮drum固定板lock-idler shaft固定杆fixed rod固定夹retaining clip固定螺钉setscrew固定螺栓captive bolt固定盘fixing plate固定圈fixed ring固定式坐椅static seat固定罩fixed hood故障诊断开关diagnostic on/off switch 刮水器wiper刮水器臂arm as-wiper刮水器臂导向件pivot gp-wiper刮水器导向件wiper pivot gp刮水器清洗器组件washer& wiper gp刮水器组件wiper gp刮油环scrap oil ring刮雨器刮板blade刮雨器刮板wiper blade挂钩shackle挂空挡组件neutralizer gp挂锁padlock管pipe管tube管道pipe work管夹clamp管接头coupling管接头union管接弯头pipe elbow管路lines管路piping管路组件lines gp管塞pipe plug管头socket管系图pipeline drawing管嘴pipe nipple光制螺栓bright bolt滚动轴承ball bearing滚花螺母khurled nut滚花螺母milled nut滚轮roller滚针rolling needle滚针套rolling needle sleeve滚针筒组件roller cage滚针止推轴承bearing-thrust滚针止推轴承thrust bearing滚针轴承multi-roll bearing滚针轴承multi-rpll bearing滚针轴承needle bearing滚针轴承rolling needle bearing 滚柱cyc. roller滚柱cyl.roller滚柱roller滚柱销roller pin滚柱轴承roller bearing滚柱轴承组件roller set滚锥轴承tapered roller bearing滚子型超越离合器roller-type overrunning clutch 滚子轴承roller bearing滚子轴承外圈roller bearing cup滚子轴承锥体roller bearing cone滚子组roller gp过滤器filter过滤器filter-screen过滤器strainer过滤器strainer-fuel tk过滤器toggle filter过滤器底壳pan as-filter过滤器管tube-filler过滤器管路组件filter lines gp过滤器架bracket过滤器外罩filter cover过滤网screen过滤系统filter system含锡黄铜admiralty metal焊接件welding piece焊接螺孔柱weld boss焊接螺母nut-weld焊接螺母weld nut焊接螺栓stud-weld焊接螺栓weld stud焊接锁紧螺母weld locknut焊接销pin-weld焊线端solder terminal合成橡胶synthetic rubber合页hinge盒duct恒温器thermostat横梁beam横梁crossmember虹吸管suction line虹吸管suction tube虹吸滤网suction filter喉箍clamp-hose喉箍collar clamp后板mount-rear后车架frame as-eng end后车架frame gp-eng end后车架rear frame后车架线路electric schematic后车架线束chassis harness后传动轴joint gp-univ后传动轴rear drive shaft后窗喷水开关rear washer swtich后大灯rear floodlight后大灯继电器rear floodlight relay后大灯开关rear floodlight switch后大灯开关switch后顶灯线束harness后顶盖rear top cover后动臂rear arm后盖rear cover后盖板cap-rear后护罩bumper as后缓冲环rear cushion后缓冲组件rear cushion gp后块block-rear后拉杆rear pole后连接板rear plate后门back door后牌照灯back license lamp后配重rear counter-weight后桥axle gp-dsc后桥axlear-engend后桥rear axle后桥摆动架swing frame of rear axle 后桥管路rear axle line后桥托架rear axle bracket后桥主传动rear axle bevel gear后桥组件rear axle gp后视镜mirror后视镜rearview mirror后退警报器alarm-back up后退警报器backup alarm后退警报装置backup alarm gp后退警报装置warning gp-bckp后小灯rear position light后小灯板rear position light plate 后小灯箱rear position light box 后压条rear bar后雨刮电机rear wiper motor后雨刮开关rear wiper switch后罩guard as-rad后罩rear cover后支承架support-trunnion后支承轴rear support bearing后支承轴trunnion后支承轴trunnion-rear后支腿rear outriggers呼吸阀breather valve呼吸器respirator护顶架overhead guard护栏guardrail护栏spillguard护套jacket护罩shield护罩shroud护罩(右)shroud-rh护罩(左)shroud-lh花键spline花键轴castellated shaft花键轴spline shaft花塞spark plug滑动齿轮slide gear滑动轴承bushing/plain bearing滑动轴承plain bearding滑动轴承plain bearing滑动轴承sliding bearing滑阀slide valve滑阀spool滑阀盖spool cover滑轨slipe rail滑环slip-ring滑键feather滑键feather key滑键slipe key滑块slipe block滑轮pulley滑闸shuttle滑脂grease化油器连杆carburetor connecting rod 环ring环圈collar环形齿轮支架ring gear carrier环形密封seal-ring缓冲垫cushion缓冲环cushion ring缓冲器bumper缓冲器damper缓冲套cushion bushing缓冲条cushion bar缓冲头cushion head换挡手柄handle-shift换气阀breather换新风装置fresh air gp簧片witch回程盘return plate回位弹簧return spring回位套return bushing回位套return sleeve回油阀体base-filter回油管return oil line回油过滤盖return oil filter cover回油过滤器return oil filter回转齿轮gear回转齿轮组件gear gp回转马达swing motor回转平台revoling frame回转式动臂swing-type boom回转支承swing bearing活动叉top clamp lever活塞piston活塞plunger活塞盖plunger cap活塞杆piston rod活塞杆rod as活塞环piston ring活塞套piston sleeve货叉fork货叉基座fork support机架rack机身body机械手transfer mechanism机油engine oil机油过滤器engine oil filter机油压力传感器engine oil pressure sensor基座base基座指示灯base indicator急救箱first-aid kit棘轮ratchet棘爪pawl集成电路circuit集油盘oil coll plate集中润滑(工作)指示灯centralized lubrication indicator集中润滑故障指示灯centralized lubrication fault indicat 集中润滑系统centralized lubrication system计时器timer技术要求requirement继电器relay继电器盒relay box继电器接头relay connector加力缸actuator加力器actuator gp加力器assistor加强钢筋reinforcement加油盖cap assem.加油管filler加油口盖fuel filling cap加油口盖oil filler cap加油系统oiling system加注盖filling cap加注器filler加注器盖filler cap夹板plywood夹板式clamp夹紧销clamping pin夹紧装置clamping arrangement夹头collet夹子clip驾驶篷canopy驾驶室cab驾驶室(含内饰件)cab（w decoration）cab（w garnishry&guard）驾驶室(含内饰件和护盖)驾驶室板组件cab as驾驶室冲压护盖 cab cover驾驶室顶灯cab overhead light驾驶室外顶灯开关cab overhead light switch 驾驶室系统cab arrangement驾驶室线路cab lines驾驶室线束cab harness驾驶室增压装置pressurizer gp驾驶室组件cab gp驾驶室左门组件door gp-cab bsc驾驶窒组件cab gp-basic架子shelf尖头螺栓nibbed bolt间隔垫圈spacing washer监测器monitor监测器monitor gp减摩轴承anti-friction bearing减压阀pressure reducing valve减压阀杆pressure reducing valve rod 减压阀杆reduction piston减压阀组件pressure reducing valve gp 减振器shock absorber减震垫shock isolator mounor减震块bumper简图说明general chart specification 渐缩弯管reducing elbow键fitting key键key交流发电机alternator胶板rubber plate胶带adhesive tape胶垫pad胶垫rubber mat胶套座clamp-boot胶条rubber bar胶条rubber strip角度接头elbow角阀angle valve角钢angle bar角钢angle steel角钢angler-lh角钢件angle as角环angle ring角铁edge iron角铁l-iron角型夹horn clamp绞盘winch脚蹬支承step support脚踏pedal脚踏组件step as铰接articulation joint铰接hinge as铰接hitch铰接车架articulation frame铰接销撑板brace铰接支承articulation bearing铰接组件hitch gp铰链hinge铰链座hinge seat铰轴joint pin铰轴pivot搅拌机mixer接地线earthing cable接点/铰接点joint接合件fastener接合面junction surface接头connector接头connector-flared接头fitting接头joint接头junction接头reducer-flared接头union-flared接头块block接头螺钉union screw接头螺帽screw-in sleeve接头套sleeve接头套sleeve-flared接头座block-manifold接头座manifold节流阀throttle valve节气阀vane节气阀散件vane kt结构图diagram drawing截止阀stop valve金属履带metal track紧定螺钉setscrew紧固装置cramping arrangement紧急&停车制动系统secondary& parking brake system 紧急制动电磁阀parking brake solenoid紧急制动阀emergency valve近/远光切换开关low/high beam switch进排气系统intake and exhaust system进气阀inlet valve进气附件intake accessory进气管intake line进气加热器air heater进气加热器intake heater进气口件diffuser进气口件diffuser as进气歧管intake manifold进气软管intake hose进气系统air intake system进水管water intake进油法兰oil inlet flange进油管路oil inlet line进油过滤盖suck oil filter cover禁踏标志don't-step sign禁踏标志no pedalling sign晶体管transistor精滤器secondary filter警报器alarm警报器组件alarm gp警报指示器alert indicator警报组件warning gp警告标牌warning tag警告标志warning sign警告牌warning plate警告指示灯warning indicator径向止推轴承angular bearing径向轴承journal bearing静音键mute key镜mirror镜组件mirror gp九针数据诊断接头diagnostic connector 举升电机lift motor举升动臂支撑lift arm support举升开关hood lift switch举升控制器controller举升控制器hood lift controller 举升控制线harness举升控制箱control unit举升控制箱lift control box举升能力表lift capacity sheet举升能力图表lift capacity chart举升油缸管路组件lift cylinder lines gp 举升支架lift bracket举升执行机构lift mechanism举升装置hood lift device矩形密封圈rectangular seal绝缘insulation绝缘板insulation-sw绝缘板insulator绝缘带tape绝缘环insulation ring绝缘套insulation bushing绝缘体insulator卡板stop plate卡箍band卡箍keeper卡环retaining卡环retaining ring卡环ring-retainer卡环ring-snap卡盘cartridge卡盘散件cartridge卡盘散件cartridge kt卡盘组件cartridge gp卡赛特恩环kassettenring卡条bar卡条retainer bar开槽螺钉slotted screw开槽螺母slotted nut开关faucet开关switch开关switch key开关tap开关板switch plate开关盒switch box开关护套switch jacket开关支架holder-switch开关支架switch holder开关座switch holder开口环snap ring开口螺栓split bolt开口销cotter开口销cotter pin开口销split cotter靠背backrest靠手armrest壳盖housing cover壳体housing可调接头adjusting connector可调气弹簧strut可调三通接头adjusting tee可调凸轮adjustable cam可换式过滤器filter可逆阀reversing valve空调air conditioner空调控制面板a/c panel空调控制面板ir conditioning control panel空调皮带a/c belt空调系统air conditioning system空调系统控制单元a/c controller空调线束a/c harness空调箱air conditioner box空调压力保护开关a/c pressure switch空调压缩机air conditioner compressor空调压缩机compressor空调压缩机支架compressor bracket空调罩a/c hood空调制冷剂refrigerant空-空中冷器air cooler空滤安装air filter mounting空滤报警开关air filter alarm switch空滤抱箍clamp空滤堵塞报警开关intake air filter alert switch空滤堵塞报警指示灯intake air filter alert indicator 空滤盖cover空滤架air filter bracket空滤壳体housing空滤器壳体air filter housing空滤器壳体housing of air filter空气阀air valve空气干燥器air desiccator空气罐air kettle空气滤清器air cleaner空气滤清器air filter空气滤清器安全滤芯safety filter element空气滤清器主滤芯main filter element空气压缩机air compressor空气预滤器air pre-filter空心轴hollow spindle空压机管路compressor hose孔盖hole cover控阀main control valve控制按钮push button控制板control plate控制板线束harness控制单元control unit控制阀control valve控制杆control lever控制开关control switch控制开关面板radio cassette player控制面板panel控制器cont控制器组件controller gp控制台console控制台switch desk控制凸轮control cam控制系统system of control控制箱control box控制元件control component扣紧件fastener扣紧片fastening shim块体block快放阀quicker couple valve快换架quicker couple bracket快换控制quick coupler control快换油缸quicker couple cylinder快换油缸管路quicker couple cylinder lines快换装置quick coupler快换装置开关quick coupler switch快换装置限位系统quick coupler limit system快速接头couplerquick coupler connector implement lin 快速连接器工作装置管路快速连接器开关quick connector switch快速连接器平台管路quick coupler connector platform line 矿物油mineral oil框盖cover-screw扩口螺母cap-flared扩展变径接头flared reducer union扩展接头flared connector扩展接头flared union扩展三通接头flared tee扩展弯头flared elbow拉杆link as-brg&拉杆pole拉杆pull rod拉杆tension bar拉杆钢管pole steel pipe拉杆销pole pin拉杆轴pole bearing拉杆轴套pole bushing拉紧螺栓tension bolt拉力弹簧tension spring拉索lanyard喇叭horn喇叭按钮horn button喇叭开关horn switch喇叭筒projector喇叭组件horn gp雷管primer冷冻机cooler冷冻油refrigerant oil冷凝风机condenser blower motor冷凝器condenser冷却系统cooling system冷却系统配管cooling system lines冷却液coolant冷却液安全标志warning decal冷却液压安全标志cooling hrdraulic safety sign 离合片disc离合器clutch离合器couplng离合器 K2coupling k2离合器鼓disc carrier离合器摩擦片clutch disc犁板moldboard连杆link连杆linkage连杆linkage rod连杆link-connecting连杆附件attachment linkage连杆装配图link assembly连接板plate连接叉fork连接电缆cabel连接电缆组件cable connect.连接法兰flange连接盖板connect cover连接杆connect rod连接管connect line连接管nipple连接管nipple-pipe连接机构connect mechanism连接件fastening连接壳体conn. housing连接壳体connect housing连接螺栓binding bolt连接器套connector socket连接器组件joint gp连接套sleeve连接销pin联动转轴linkage shaft联锁interlock联轴/联接coupling联轴器安装coupling mounting链chain链轮sprocket链轮sprocket gear链条chains梁rail梁rail as零位调整机构zeroing mechanism流量放大阀flow amplifying valve流量放大阀valve gp-ster流量放大阀管路flow amplifying valve lines 柳工商标lg brand六角螺母hexagon nut六角螺塞hexagon plug六角头螺钉hexagon screw六角头螺栓hexagon bolt滤清器元件filter element滤清器组件filter gp滤头screen滤网screen滤网strainer滤网接头fitting滤芯filter core滤芯filter element滤芯过滤纸filter paper滤芯压座filter element seat滤油器fuel screen滤油器螺杆oil filter stud滤油器螺杆stud-filter滤油器螺栓bolt-filter滤油器螺栓oil filter bolt路熔断器circuit breaker履带track履带板track shoe履带横向宽度transverse width over tracks 履带架track frame履带式crawler履带式挖掘机crawler excavator轮wheel轮边支承hub carrier轮毂hub轮毂件hub as轮毂螺母hub nut轮毂螺母nut of hub轮毂螺栓bolt轮毂托架hub carrier轮盘wheel gp轮胎tire轮胎轮辋系统tire&rim ar轮胎组件tire gp轮辋rim轮辋rim gp-dmount -a轮辋螺母rim nut轮辋螺母wheel nut轮辋螺栓rim bolt轮辋螺栓wheel bolt轮辋组件rim as螺钉screw螺杆bolt-guide螺杆screw rod螺杆threaded rod螺帽screw cap螺帽扳手nut wrench螺母nut螺母nut package螺母nut-bat terminal螺母nut-bulkhead螺母nut-clinch螺母nut-face seal螺母nut-flared螺母nut-full螺母nut-hex螺母nut-hexagon螺母nut-jam螺母nut-lock螺母nut-m5 hex full螺母nut-mounting螺母nut-retainer螺母nut-tab weld螺母块nut block螺母组件nut gp螺塞plug螺塞plug-o-ring螺塞plug-o-ring spl螺塞screw plug螺塞件plug as螺塞组件plug as-o-ring螺拴bolt package螺拴bolt-12 point hd螺拴bolt-brake band螺拴bolt-flat head螺拴bolt-plow螺拴bolt-retainer螺拴bolt-shoulder螺拴bolt-terminal螺拴screw-filler cap螺栓bolt螺栓bolt-pivot螺栓bolt-self lcking螺栓bolt-stop螺栓thread bo1t螺栓组件bolt as螺套screw sleeve螺纹保护装置thread protector螺纹机构thread mechanism螺纹天线antenna(gps)螺旋齿轮spiral gear螺旋阀screw-down stop valve 螺旋千斤顶jack-screw螺旋伞齿轮helical bevel gear螺旋圆锥齿轮spiral bevel wheel螺旋圆锥齿轮spiral-tooth bevel gear 螺旋运动spiral movement螺旋锥齿轮减速bevel gear reduction螺柱stud马达motor马达motor as-wiper马达安装motor mounting马达支架motor bracket埋头螺钉countersunk bolt锚式销制动anchor pin brake 锚栓anchor bolt铆钉groove stud铆钉rivet铆钉螺母rivet nut梅花爪clud-shaped digger 门door门钩door hook门架mast门架衬套mast lining门架滑道mast slideway门胶条door bar门铰链door hinge门扣door buckle门框doorframe门框frame-door门框焊件frame as门锁door lock门锁latch as-door门锁外开关handle-outside门组件door gp密封板seal plate密封挡圈seal retainer密封垫gasket密封垫圈seal washer密封垫圈sealing disc密封堵plug密封盖seal cover密封固定座retainer-o seal密封环prof. seal ring密封环sealing ring密封剂sealant密封胶sealant密封接头seal connector密封圈grommet-mount密封圈seal ring密封圈seal-quad ring密封圈-矩形seal-d ring密封塞plug密封塞plug-sealing密封三通接头seal tee密封套夹boot clamp密封条sealent密封条sealer密封条(右)seal-rh密封条(左)seal-lh密封弯头seal elbow密封压盖packing gland密封组件seal gp密封组件seal kit-hyd cyl密封组件seal kt-whl cyl面板face plate面板panel面板箱panel灭火器fire extinguisher铭牌designation strip铭牌label铭牌name plate铭牌nameplate铭牌type plate铭牌铆钉nameplate rivet模式切换标志mode switch sign模式切换警告mode switch warning摩擦板friction plate摩擦衬片friction lining摩擦鼓clutch drum摩擦环ring-wear摩擦轮adhesion wheel摩擦轮sheave of friction摩擦盘clutch disc摩擦片disc摩擦片facing摩擦片安装assembl. of i.and o clutch disc摩擦片隔离架disc carrier摩擦片支承disc support摩擦片支架disc bracket摩檫环clutch ring摩损环wear ring内/外气调节杆internal and external air adjusting l 内板angle-inner内部密封inner seal内衬lining内齿轮inner gear内齿轮internal gear内齿轮支撑架inner gear bracket内齿圈gear ring内齿圈ring gear内齿圈支承座组件ring gear carrier内弹簧inner spring内环inner ring内六角定位螺钉etscrew-socket内六角螺钉setscrew-socket内六角螺栓bolt-socket head内六角头hexagon socket head。

各行业专业英语词汇–机械类机械类是一个广泛的行业，包括了制造、工程、建筑、运输等多个分支。

在跨国公司、跨境贸易和国际合作领域，专业的机械类英语词汇是十分必要的。

下面就为大家整理了一些常见的机械类英语词汇。

设备和工具•Conveyor：传送带•Crane：起重机•Drill：钻机•Grinder：砂轮机•Hacksaw：手用金属锯•Hoist：吊车•Lathe：车床•Milling machine：铣床•Pneumatic saw：气动锯•Press：压床•Sander：毛刷磨床•Screwdriver：螺丝刀•Welding machine：焊接机零件和组件•Bearing：轴承•Bolt：螺栓•Brake pad：刹车片•Cam：凸轮•Clamp：夹子•Coupling：联轴器•Gear：齿轮•Gasket：垫片•Hydraulic cylinder：液压缸•Lock nut：锁紧螺母•Nut：螺母•Piston：活塞•Pipe fitting：管接头•Seal：密封件•Spring：弹簧•Washer：垫圈•Valve：阀门流程和工艺•Assembly line：生产线•Automation：自动化•Blueprint：蓝图•CNC (Computer Numerical Control)：数控•Manufacturing process：制造工艺•Mould：模具•Quality control：质量控制•Specification：规格•Tolerance：公差•Welding：焊接职业和术语•Engineer：工程师•Fabricator：制造工•Fitter：装配工•Machinist：孔加工工•Mechanic：机械师•Operator：操作员•Technician：技术员•Threader：螺纹车工以上是机械类行业常用的英语词汇，虽然并不全面，但肯定能帮助你在机械行业的沟通中更加得心应手。

机械名词英译汉大全机械行业是一个广泛的领域，其中包含了许多特定的名词和术语。

了解这些名词的英文翻译对于学习机械工程和通信非常重要。

本文将带您了解机械名词英译汉的大全，让您更好地掌握机械工程领域的专业术语。

A•Acceleration: 加速度•Actuator:执行器•Angular velocity: 角速度•Automation:自动化•Axis:轴B•Bearing:轴承•Bevel gear:锥齿轮•Bolt:螺栓•Bore:孔径•Bushing:套筒C•Cam:凸轮•Carrier:承载体•Clutch:离合器•Crankshaft:曲轴•Cylinder:气缸D•Deflection:挠曲•Die:模具•Drive:驱动•Dynamic:动态的E•Efficiency:效率•Elasticity:弹性•Encoder:编码器•Engine:发动机F•Fastener:紧固件•Fatigue:疲劳•Friction:摩擦•Fuel:燃料G•Gear:齿轮•Generator:发电机•Grinder:砂轮•Guide:导轨H•Heat exchanger:换热器•Hydraulic:液压的•Hose:软管•Hub:轮毂I•Idle:空闲的•Inertia:惯性•Inlet:进口•Implement:工具•Jack:千斤顶•Joint:接头•Junction:连接点•Jig:夹具K•Key:键•Kinematics:运动学•Knurling:滚花L•Laser:激光•Lever:杠杆•Lubricant:润滑剂•Lathe:车床•Machine:机器•Machining:加工•Maintenance:维护•Martensite:马氏体N•Nozzle:喷嘴•Newton:牛顿•Nonferrous:有色的•Nylon:尼龙O•Orifice:孔隙•Outlet:出口•Overload:过载P•Piston:活塞•Pulley:滑轮•Pressure:压力•Pneumatic:气动的Q•Quenching:淬火•Quick-release:快速释放•Quill:芯轴•Queue:队列R•Reducer:减速器•Reliability:可靠性•Rivet:铆钉S•Shaft:轴•Screw:螺丝•Spring:弹簧•Static:静态的T•Torque:力矩•Tolerance:公差•Thread:螺纹•Turbine:涡轮机U•Ultrasonic:超声的•Upset:擴頭•Uniform:均匀的•U-bolt:U形螺栓V•Velocity:速度•Valve:阀门•Vibration:振动•Vacuum:真空W•Welder:焊工•Worm gear:蜗杆齿轮•Welding:焊接•Wear:磨损X•X-axis:X轴•Xenon:氙气•X-ray:X射线•Xerography:静电复印Y•Yoke:夹具•Y-axis:Y轴•Yield strength:屈服强度•Yarn:纱线Z•Z-axis:Z轴•Zinc:锌•Zero clearance:零间隙•Zone:区域以上是机械名词英译汉大全，包含了机械工程领域中常见的名词和术语。

专业机械词汇中英文对照一、引言随着工业技术的进步和现代化制造业的不断发展，机械工程日益成为全球经济的重要支柱。

机械领域技术含量高，而机械行业的专业术语更是繁多，对机械从业人员的技能水平有较高的要求。

因此，机械行业专业词汇的掌握是机械从业人员必不可少的基本功之一。

针对此问题，本文对常见的机械专业词汇进行了分组和翻译，并收集了一些实例，以帮助读者更好地了解机械行业术语中英文对照。

二、机械专业词汇的分类机械专业词汇可以分为多个类别。

下面是几个常见的机械专业词汇的分类。

1、机械零件类英文中文英文中文Bolt 螺栓Nut 螺母Screw 螺钉Washer 垫圈Spring 弹簧Cotter Pin 销子Sleeve 套管Bearing 轴承Key 键 Shaft 轴Pulley 皮带轮Crankshaft曲轴Cam 凸轮Rod 杆2、机械工具类英文中文英文中文Hammer 锤子Axe 斧子Saw锯子Chisel 凿子Plier 钳子Screwdriver 螺丝刀Wrench扳手Punch 冲锋器Drill 钻头Tap 丝锥3、机械设备类英文中文英文中文Lathe 车床Milling Machine 铣床Grinding Machine 磨床Drilling Machine 钻床Bending Machine 折弯机Shearing Machine 剪切机Press 冲压机Forging Machine 锻压机三、机械专业词汇的实例以下是一些常见机械专业词汇的实例。

1、膨胀螺栓Expansion Bolt膨胀螺栓是一种在混凝土结构中使用的固定件。

在钻好混凝土孔之后，将整体膨胀螺栓插入孔中，再旋转螺栓使其内部的部件（如锥形套筒等）与混凝土结构紧密连接。

因为它的安装方式是从孔内部完成的，所以外表看起来不会有凸起的螺纹。

2、连杆Connecting Rod连杆是内燃机中重要的零件。

它将活塞与曲轴连接在一起，通过曲轴的旋转运动，驱动活塞上下运动，从而产生活塞运动的功效。

專業術語解釋一、軟體1、CAD：電腦輔助設計，通常指設計軟體CAM：電腦輔助製造，通常指編寫CNC加工程式的軟體。

2D：指二維圖形，即平面圖形。

3D：指三維圖形，即立體圖形.CAE：電腦輔助分析，軟體.CAPP:電腦輔助工藝規劃，軟體。

2、常用的軟體有：二、材料鋼材三、銑刀術語四、刀把刀把：1、按銑刀夾持方式分為：側固式筒夾式油壓式牙固式熱縮式2、按與主軸的接合形式分為：HSK和BT①HSK刀把: 1:10錐度，雙面接觸，HSK刀把有A、B、C、D、E、F六種形式.A形式鍵槽在斜錐底部，最常見，適合一般高速，大扭力機器，如HSKA63，A80，A100B形式直徑較大且外徑上有鍵槽,一般不太常見。

C、D形式應用於手動換刀E、F形式適合高速、小扭力，刀把外徑無鍵槽或辨認孔，如HSK E32 E40 E50 F63等。

②BT和SK刀把：7：24錐度，V型接合形式，在日本稱BT，歐洲稱SK刀把，常用的有BT30、BT40、BT50等市面上常用的刀具、刀把品牌：山特維克可樂滿Sandvik Coromant 肯納Kennametal 瓦爾特（Walter）伊斯卡Iscar 山高Seco 藍幟LMT 蒂泰克斯Titex 埃莫克Emuge 瑪帕MAPAL 阿諾AHNO 攀時PLANSEE 英格索爾Ingersoll 萬耐特Valenite考邁特Komet 鈷領Guehring 威迪亞Widia 瑞貝格Rubig 沃好特Wohihaupter 多馬DORMER 飛特Fette Fraiss TBT 法蘭肯Franken 雄克Schunk 博士BASS Koyemann Stellram 海默Haimer CeramTec歐馬Urma PH HORN PH 瓦格斯VARGUS JET DC DIXI SGS EPB CARMEX 銑星MillStar 歐華Erowa Heule 豪費德Hollfelder 泰拉天時Ceratizit GARRTOOL SOMTA 三菱MITSUBISHI 歐士機OSC 彌滿和YAMAWA 黛傑Dijet 住友Sumitomo 日立HATACHI 恩蒂NT 名古屋Nastec 東芝泰珂洛TUNGALOY 大昭和BIG 京瓷Kyocera NTK 不二越NACHI 日研NIKKEN 奧古嘉OKK 特固克TaeguTec 養志園YG-1 高樂KORLOY 多仁DINESTL YU.S Micro100(美國微百) STK WTE （德國) pokolm （德國）五、高速加工六、數控機床與加工中心1、數控機床：采用數控技術控制的機床，或者說裝備了數控系統的機床稱數控機床.2、加工中心：裝有刀庫及自動換刀系統的數控機床稱之為加工中心。

常用机械加工工艺术语（英汉对照）1 工艺基本概念1.1 一般概念1.1.1数控加工：numerical control machining根据被加工零件图样和工艺要求，编制成以数码表示的程序输入到机床的数控装置或控制计算机中，以控制工件和工具的相对运动，使之加工出合格零件的方法。

1.2生产对象1.2.1 原材料：raw material投入生产过程以创新产品的物质。

1.2.2主要材料：primary material; direct material构成产品实体的材料。

1.2.3辅助材料：auxiliary material; indirect material在生产中起辅助作用而不构成产品实体的材料。

1.2.4代用材料：substituent在使用功能上能够代替原设计要求的材料。

它具有被代替材料所具备的全部或主要性能。

1.2.5易损材料：quick-wear material在正常使用条件下，容易损坏或失效的材料。

1.2.6废料：waste material在制造某种产品过程中，剩下的而对本生产对象不再有用的材料。

1.2.7型材：section金属或非金属材料通过拉制、轧制或压制等方法所获得的具有特定几何形状截面的材料。

1.2.8板材：plate金属或非金属材料通过轧制或压制等方法而获得的各种不同厚度的板状材料。

1.2.9棒材：bar stock金属或非金属材料通过拉延、轧制工艺获得的圆、方、六角形截面的材料。

1.2.10铸件：casting将熔融金属浇入铸型，凝固后所得到的金属制件或毛坯。

1.2.11锻件：forgings金属材料经过锻造变形而得到的工件或毛坯。

1.2.12焊接件：weldment用焊接方法而得到的结合件。

1.2.13模压件：molded parts利用模具压制的工件。

1.2.14冲压件：stamping用冲压的方法制成的工件或毛坯。

1.2.15合格品：accepted product;;conforming article通过检验质量特性符合标准要求的制品。

机械专业术语（英语）大全机械专业术语，中英文对照！阿基米德蜗杆Archimedes worm安全系数safety factor; factor of safety安全载荷safe load凹面、凹度concavity扳手wrench板簧flat leaf spring半圆键woodruff key变形deformation摆杆oscillating bar摆动从动件oscillating follower摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile摆线运动规律cycloidal motion摆线针轮cycloidal-pin wheel包角angle of contact保持架cage背对背安装back-to-back arrangement背锥back cone ；normal cone背锥角back angle背锥距back cone distance比例尺scale比热容specific heat capacity闭式链closed kinematic chain闭链机构closed chain mechanism臂部arm变频器frequency converters变频调速frequency control of motor speed变速speed change变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient标准齿轮standard gear标准直齿轮standard spur gear表面质量系数superficial mass factor表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness并联式组合combination in parallel并联机构parallel mechanism并联组合机构parallel combined mechanism并行工程concurrent engineering并行设计concurred design, CD不平衡相位phase angle of unbalance不平衡imbalance (or unbalance)不平衡量amount of unbalance不完全齿轮机构intermittent gearing波发生器wave generator波数number of waves补偿compensation参数化设计parameterization design, PD残余应力residual stress操纵及控制装置operation control device槽轮Geneva wheel槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate槽凸轮groove cam侧隙backlash差动轮系differential gear train差动螺旋机构differential screw mechanism差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor承载能力bearing capacity成对安装paired mounting尺寸系列dimension series齿槽tooth space齿槽宽spacewidth齿侧间隙backlash齿顶高addendum齿顶圆addendum circle齿根高dedendum齿根圆dedendum circle齿厚tooth thickness齿距circular pitch齿宽face width齿廓tooth profile齿廓曲线tooth curve齿轮gear齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack齿轮插刀pinion cutter; pinion-shaped shaper cutter 齿轮滚刀hob ,hobbing cutter齿轮机构gear齿轮轮坯blank齿轮传动系pinion unit齿轮联轴器gear coupling齿条传动rack gear齿数tooth number齿数比gear ratio齿条rack齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain齿形系数form factor齿式棘轮机构tooth ratchet mechanism插齿机gear shaper重合点coincident points重合度contact ratio冲床punch传动比transmission ratio, speed ratio传动装置gearing; transmission gear传动系统driven system传动角transmission angle传动轴transmission shaft串联式组合combination in series串联式组合机构series combined mechanism串级调速cascade speed control创新innovation ; creation创新设计creation design垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face从动件停歇follower dwell从动件运动规律follower motion从动轮driven gear粗线bold line粗牙螺纹coarse thread大齿轮gear wheel打包机packer打滑slipping带传动belt driving带轮belt pulley带式制动器band brake单列轴承single row bearing单向推力轴承single-direction thrust bearing单万向联轴节single universal joint单位矢量unit vector当量齿轮equivalent spur gear; virtual gear当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat导程lead导程角lead angle等加等减速运动规律parabolic motion; constant acceleration and deceleration motion 等速运动规律uniform motion; constant velocity motion等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia等效动力学模型dynamically equivalent model底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance定轴轮系ordinary gear train; gear train with fixed axes动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity动力润滑dynamic lubrication动平衡dynamic balance动平衡机dynamic balancing machine动态特性dynamic characteristics动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch端面齿廓transverse tooth profile端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower对心直动从动件radial (or in-line ) translating follower对心移动从动件radial reciprocating follower对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism 多列轴承multi-row bearing多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line发生面generating plane法面normal plane法面参数normal parameters法面齿距normal circular pitch法面模数normal module法面压力角normal pressure angle法向齿距normal pitch法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force反馈式组合feedback combining反向运动学inverse ( or backward) kinematics反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy分度线reference line; standard pitch line分度圆reference circle; standard (cutting) pitch circle 分度圆柱导程角lead angle at reference cylinder分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism复杂机构complex mechanism杆组Assur group干涉interference刚度系数stiffness coefficient刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law根切undercutting公称直径nominal diameter高度系列height series功work工况系数application factor工艺设计technological design工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads工作空间working space工作应力working stress工作阻力effective resistance工作阻力矩effective resistance moment公法线common normal line公共约束general constraint公制齿轮metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force惯性力部分平衡partial balance of shaking force 惯性主矩resultant moment of inertia惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing滚动轴承代号rolling bearing identification code 滚针needle roller滚针轴承needle roller bearing滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator函数生成function generation含油轴承oil bearing耗油量oil consumption耗油量系数oil consumption factor赫兹公式H. Hertz equation合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return回转体平衡balance of rotors混合轮系compound gear train积分integrate机电一体化系统设计mechanical-electrical integration system design 机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism机构学mechanism机构运动设计kinematic design of mechanism机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion机器machine机器人robot机器人操作器manipulator机器人学robotics技术过程technique process技术经济评价technical and economic evaluation技术系统technique system机械machinery机械创新设计mechanical creation design, MCD机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery机械动力设计dynamic design of machinery机械动力学dynamics of machinery机械的现代设计modern machine design机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery机械手manipulator机械设计machine design; mechanical design机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency机械原理theory of machines and mechanisms机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD基圆base circle基圆半径radius of base circle基圆齿距base pitch基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone急回机构quick-return mechanism急回特性quick-return characteristics急回系数advance-to return-time ratio急回运动quick-return motion棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position极位夹角crank angle between extreme (or limiting) positions计算机辅助设计computer aided design, CAD计算机辅助制造computer aided manufacturing, CAM计算机集成制造系统computer integrated manufacturing system, CIMS 计算力矩factored moment; calculation moment计算弯矩calculated bending moment加权系数weighting efficient加速度acceleration加速度分析acceleration analysis加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio减速齿轮、减速装置reduction gear减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear渐开线发生线generating line of involute渐开线方程involute equation渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing角接触推力轴承angular contact thrust bearing角接触向心轴承angular contact radial bearing角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design紧边tight-side紧固件fastener径节diametral pitch径向radial direction径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load径向基本额定动载荷basic dynamic radial load rating 径向基本额定静载荷basic static radial load tating径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form矩形牙嵌式离合器square-jaw positive-contact clutch 绝对尺寸系数absolute dimensional factor绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism抗压强度compression strength开口传动open-belt drive开式链open kinematic chain开链机构open chain mechanism可靠度degree of reliability可靠性reliability可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism空间连杆机构spatial linkage空间凸轮机构spatial cam空间运动副spatial kinematic pair空间运动链spatial kinematic chain空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation离心力centrifugal force离心应力centrifugal stress离合器clutch离心密封centrifugal seal理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism 力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain链传动装置chain gearing链轮sprocket ; sprocket-wheel ; sprocket gear ; chain wheel 联组V 带tight-up V belt联轴器coupling ; shaft coupling两维凸轮two-dimensional cam临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line绿色设计green design ; design for environment马耳他机构Geneva wheel ; Geneva gear马耳他十字Maltese cross脉动无级变速pulsating stepless speed changes脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component密封装置sealing arrangement面对面安装face-to-face arrangement面向产品生命周期设计design for product`s life cycle, DPLC 名义应力、公称应力nominal stress模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction摩擦圆friction circle磨损abrasion ;wear; scratching末端执行器end-effector目标函数objective function耐腐蚀性corrosion resistance耐磨性wear resistance挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear内齿圈ring gear内力internal force内圈inner ring能量energy能量指示图viscosity逆时针counterclockwise (or anticlockwise)啮出engaging-out啮合engagement, mesh, gearing啮合点contact points啮合角working pressure angle啮合线line of action啮合线长度length of line of action啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图NomogramO 形密封圈密封O ring seal盘形凸轮disk cam盘形转子disk-like rotor抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism 拼接matching评价与决策evaluation and decision频率frequency平带flat belt平带传动flat belt driving平底从动件flat-face follower平底宽度face width平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane平衡质量balancing mass平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key其他常用机构other mechanism in common use起动阶段starting period启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism曲柄滑块机构slider-crank (or crank-slider) mechanism 曲柄摇杆机构crank-rocker mechanism曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion球销副sphere-pin pair球坐标操作器polar coordinate manipulator燃点spontaneous ignition热平衡heat balance; thermal equilibrium人字齿轮herringbone gear冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant三角形花键serration spline三角形螺纹V thread screw三维凸轮three-dimensional cam三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass少齿差行星传动planetary drive with small teeth difference 设计方法学design methodology设计变量design variable设计约束design constraints深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift实际廓线cam profile十字滑块联轴器double slider coupling; Oldham‘s coup ling 矢量vector输出功output work输出构件output link输出机构output mechanism输出力矩output torque输出轴output shaft输入构件input link数学模型mathematic model实际啮合线actual line of action双滑块机构double-slider mechanism, ellipsograph双曲柄机构double crank mechanism双曲面齿轮hyperboloid gear双头螺柱studs双万向联轴节constant-velocity (or double) universal joint 双摇杆机构double rocker mechanism双转块机构Oldham coupling双列轴承double row bearing双向推力轴承double-direction thrust bearing松边slack-side顺时针clockwise瞬心instantaneous center死点dead point四杆机构four-bar linkage速度velocity速度不均匀( 波动) 系数coefficient of speed fluctuation 速度波动speed fluctuation速度曲线velocity diagram速度瞬心instantaneous center of velocity塔轮step pulley踏板pedal台钳、虎钳vice太阳轮sun gear弹性滑动elasticity sliding motion弹性联轴器elastic coupling ; flexible coupling弹性套柱销联轴器rubber-cushioned sleeve bearing coupling 套筒sleeve梯形螺纹acme thread form特殊运动链special kinematic chain特性characteristics替代机构equivalent mechanism调节modulation, regulation调心滚子轴承self-aligning roller bearing调心球轴承self-aligning ball bearing调心轴承self-aligning bearing调速speed governing调速电动机adjustable speed motors调速系统speed control system调压调速variable voltage control调速器regulator, governor铁磁流体密封ferrofluid seal停车阶段stopping phase停歇dwell同步带synchronous belt同步带传动synchronous belt drive凸的，凸面体convex凸轮cam凸轮倒置机构inverse cam mechanism凸轮机构cam , cam mechanism凸轮廓线cam profile凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve凸缘联轴器flange coupling图册、图谱atlas图解法graphical method推程rise推力球轴承thrust ball bearing推力轴承thrust bearing退刀槽tool withdrawal groove退火anneal陀螺仪gyroscopeV 带V belt外力external force外圈outer ring外形尺寸boundary dimension万向联轴器Hooks coupling ; universal coupling 外齿轮external gear弯曲应力beading stress弯矩bending moment腕部wrist往复移动reciprocating motion往复式密封reciprocating seal网上设计on-net design, OND微动螺旋机构differential screw mechanism位移displacement位移曲线displacement diagram位姿pose , position and orientation稳定运转阶段steady motion period稳健设计robust design蜗杆worm蜗杆传动机构worm gearing蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear蜗杆形凸轮步进机构worm cam interval mechanism蜗杆旋向hands of worm蜗轮worm gear涡圈形盘簧power spring无级变速装置stepless speed changes devices无穷大infinite系杆crank arm, planet carrier现场平衡field balancing向心轴承radial bearing向心力centrifugal force相对速度relative velocity相对运动relative motion相对间隙relative gap象限quadrant橡皮泥plasticine细牙螺纹fine threads销pin消耗consumption小齿轮pinion小径minor diameter橡胶弹簧balata spring修正梯形加速度运动规律modified trapezoidal acceleration motion 修正正弦加速度运动规律modified sine acceleration motion斜齿圆柱齿轮helical gear斜键、钩头楔键taper key泄漏leakage谐波齿轮harmonic gear谐波传动harmonic driving谐波发生器harmonic generator斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio行星齿轮装置planetary transmission行星轮planet gear行星轮变速装置planetary speed changing devices行星轮系planetary gear train形封闭凸轮机构positive-drive (or form-closed) cam mechanism 虚拟现实virtual reality虚拟现实技术virtual reality technology, VRT虚拟现实设计virtual reality design, VRD虚约束redundant (or passive) constraint许用不平衡量allowable amount of unbalance许用压力角allowable pressure angle许用应力allowable stress; permissible stress悬臂结构cantilever structure悬臂梁cantilever beam循环功率流circulating power load旋转力矩running torque旋转式密封rotating seal旋转运动rotary motion选型type selection压力pressure压力中心center of pressure压缩机compressor压应力compressive stress压力角pressure angle牙嵌式联轴器jaw (teeth) positive-contact coupling雅可比矩阵Jacobi matrix摇杆rocker液力传动hydrodynamic drive液力耦合器hydraulic couplers液体弹簧liquid spring液压无级变速hydraulic stepless speed changes液压机构hydraulic mechanism一般化运动链generalized kinematic chain移动从动件reciprocating follower移动副prismatic pair, sliding pair移动关节prismatic joint移动凸轮wedge cam盈亏功increment or decrement work应力幅stress amplitude应力集中stress concentration应力集中系数factor of stress concentration应力图stress diagram应力—应变图stress-strain diagram优化设计optimal design油杯oil bottle油壶oil can油沟密封oily ditch seal有害阻力useless resistance有益阻力useful resistance有效拉力effective tension有效圆周力effective circle force有害阻力detrimental resistance余弦加速度运动cosine acceleration (or simple harmonic) motion 预紧力preload原动机primer mover圆带round belt圆带传动round belt drive圆弧齿厚circular thickness圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover原始机构original mechanism圆形齿轮circular gear圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair圆柱式凸轮步进运动机构barrel (cylindric) cam圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring圆柱螺旋压缩弹簧cylindroid helical-coil compression spring圆柱凸轮cylindrical cam圆柱蜗杆cylindrical worm圆柱坐标操作器cylindrical coordinate manipulator圆锥螺旋扭转弹簧conoid helical-coil compression spring圆锥滚子tapered roller圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears圆锥角cone angle原动件driving link约束constraint约束条件constraint condition约束反力constraining force跃度jerk跃度曲线jerk diagram运动倒置kinematic inversion运动方案设计kinematic precept design运动分析kinematic analysis运动副kinematic pair运动构件moving link运动简图kinematic sketch运动链kinematic chain运动失真undercutting运动设计kinematic design运动周期cycle of motion运动综合kinematic synthesis运转不均匀系数coefficient of velocity fluctuation 运动粘度kenematic viscosity载荷load载荷—变形曲线load—deformation curve载荷—变形图load—deformation diagram窄V 带narrow V belt毡圈密封felt ring seal展成法generating张紧力tension张紧轮tension pulley振动vibration振动力矩shaking couple振动频率frequency of vibration振幅amplitude of vibration正切机构tangent mechanism正向运动学direct (forward) kinematics正弦机构sine generator, scotch yoke织布机loom正应力、法向应力normal stress制动器brake直齿圆柱齿轮spur gear直齿锥齿轮straight bevel gear直角三角形right triangle直角坐标操作器Cartesian coordinate manipulator 直径系数diametral quotient直径系列diameter series直廓环面蜗杆hindley worm直线运动linear motion直轴straight shaft质量mass质心center of mass执行构件executive link; working link质径积mass-radius product智能化设计intelligent design, ID中间平面mid-plane中心距center distance中心距变动center distance change中心轮central gear中径mean diameter终止啮合点final contact, end of contact周节pitch周期性速度波动periodic speed fluctuation周转轮系epicyclic gear train肘形机构toggle mechanism轴shaft轴承盖bearing cup轴承合金bearing alloy轴承座bearing block轴承高度bearing height轴承宽度bearing width轴承内径bearing bore diameter轴承寿命bearing life轴承套圈bearing ring轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle轴向axial direction轴向齿廓axial tooth profile轴向当量动载荷dynamic equivalent axial load轴向当量静载荷static equivalent axial load轴向基本额定动载荷basic dynamic axial load rating 轴向基本额定静载荷basic static axial load rating轴向接触轴承axial contact bearing轴向平面axial plane轴向游隙axial internal clearance轴向载荷axial load轴向载荷系数axial load factor轴向分力axial thrust load主动件driving link主动齿轮driving gear主动带轮driving pulley转动导杆机构whitworth mechanism转动副revolute (turning) pair转速swiveling speed ; rotating speed转动关节revolute joint转轴revolving shaft转子rotor转子平衡balance of rotor装配条件assembly condition锥齿轮bevel gear锥顶common apex of cone锥距cone distance锥轮bevel pulley; bevel wheel锥齿轮的当量直齿轮equivalent spur gear of the bevel gear锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear子程序subroutine子机构sub-mechanism自动化automation自锁self-locking自锁条件condition of self-locking自由度degree of freedom, mobility总重合度total contact ratio总反力resultant force总效率combined efficiency; overall efficiency组成原理theory of constitution组合齿形composite tooth form组合安装stack mounting组合机构combined mechanism阻抗力resistance最大盈亏功maximum difference work between plus and minus work 纵向重合度overlap contact ratio纵坐标ordinate组合机构combined mechanism最少齿数minimum teeth number最小向径minimum radius作用力applied force坐标系coordinate frame机械专利翻译词汇三千个Assembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Electric screw driver 电动起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具)pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine 热熔机repair 修理operator 作业员QC 品管supervisor 课长ME 制造工程师cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. Inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试V oltage switch of SPS 电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department 人力资源部production department 生产部门planning department 企划部QC Section 品管科stamping factory 冲压厂painting factory 烤漆厂molding factory 成型厂common equipment 常用设备uncoiler and straightener 整平机punching machine 冲床robot 机械手hydraulic machine 油压机lathe 车床planer 刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机staker=reviting machine 铆合机position 职务president 董事长general manager 总经理special assistant manager 特别助理factory director 厂长department director 部长deputy manager | =vice manager 副经理section supervisor 课长deputy section supervisor =vice section superisor 副课长group leader/supervisor 组长line supervisor 线长assistant manager 助理to move, to carry, to handle 搬运be put in storage 入库pack packing 包装to apply oil 擦油to file burr 锉毛刺final inspection 终检to connect material 接料to reverse material 翻料wet station 沾湿台Tiana 天那水cleaning cloth 抹布to load material 上料to unload material 卸料to return material/stock to 退料scraped |'skræpid| 报废scrape 刮;削deficient purchase 来料不良manufacture procedure 制造过程deficient manufacturing procedur 制造过程不良oxidation 氧化scratch 刮伤dents 压痕defective upsiding down 抽芽不良defective to staking 铆合不良embedded lump 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力education and training 教育与训练proposal improvement 提案改善spare parts=buffer 备件forklift 叉车trailer=long vehicle 拖板车compound die 合模die locker 锁模器pressure plate=plate pinch 压板bolt 螺栓name of a department 部门名称administration/general affairs dept 总务部automatic screwdriver 电动启子thickness gauge 厚薄规gauge(or jig) 治具power wire 电源线buzzle 蜂鸣器defective product label 不良标签identifying sheet list 标示单screwdriver holder 起子插座pedal 踩踏板stopper 阻挡器flow board 流水板。

Piping work: 铺管工程Steam trace: 加热蒸汽管道Cutting: 切割socket weld承插焊接fillet weld角焊,填角焊branch connection分支接续fabrication tolerance.制造容差local heat treatment 局部热处理threaded pipe螺纹管seal welding.密封焊接flange joint 凸缘接头undercut 底切feeder馈电线conduit outlet电线引出口seal fitting 密封接头, 密封配件Screw thread lubricant螺纹润滑剂Seal: 绝缘层weld reinforcement 焊缝补强lock washer 锁紧[止动, 防松]垫圈electrical panel.配电板,配电盘nipple螺纹接头zinc plated.镀锌的ring joint 环接, 围缘接合bolt 螺栓control: 控制器National Electrical Code 全国电气规程master schedule 主要图表, 综合图表, 设计任务书, 主要作业表torque wrench 转矩扳手job site 施工现场flange connection.凸缘联接Hard hat：安全帽Goggles：护目镜stockpile贮存packing list装箱单crate: 柳条箱purchased material list原材料进货单back-feed反馈wire coil线盘，线卷，NPT thread. 美国标准锥管螺纹cable gland 电缆衬垫terminal block线弧, 接头排接线盒, 接线板, 线夹power drill机械钻connector. 接线器insulated sleeve绝缘套管wire connector接线器wire terminal电线接头control wiring控制线路motor lead电动机引出线power wiring电力布线tender document．提供证件orifice plate.挡板nut 螺母flange gasket 法兰垫片dimensional inspection 尺寸检验burn through 烧蚀piping system.管道系统reinforcement of weld加强焊缝fabrication.制造dye penetrant examination染料渗透试验法magnetic particle examination 磁粉检验girth weld环形焊缝cement lined piping 水泥衬里weld joint 焊缝, 焊接接头spool drawing 管路图, 管路详图.spot test 抽查, 当场测试butt weld 对接焊缝Random Radiography随机射线照相检查radiographic examination 射线照相检查assembly.装配erection 架设examination试验cable tray.电缆盘rigid steel conduit 钢制电线管power control 功率控制arc welding 电弧焊control cable控制电缆操纵索normal bend 法向[法线]弯管cable glands: 电缆衬垫exfoliation剥落power receptacle 电力插座grounding conductor 接地导体lighting fixture照明器材junction box 分线箱race way 电缆管道terminal box接线盒distribution board配电盘, 配电屏receptacle 插座tumble switch.翻转开关,拨动式开关cathodic protection system 阴极保护系统Circuit breaker断路开关amplifier panel 放大器盘control console 控制台electrical material电气材料convenience receptacle.电源插座cable gland 电缆衬垫TIG：Tungsten-arc Inert-Gas welding 钨极电弧惰性气体保护焊filler rod焊条tensile strength 抗张强度shield gas 保护气体shield jig保护夹具high frequency generator.高频发电机welding rod 焊条filler metal 焊料, 焊丝shop fabrication 车间制造field installation 现场安装welding bead 焊道both sides welding.双面焊接residual stress 残余应力electrode 电焊条condensation 冷凝longitudinal.纵向的horizontal line 水平线circumferential joint 周圈接缝nondestructive examination.非破坏性检验,qualification: 合格性construction work施工工程welded joint焊接缝焊接节点gas cutting.气割arc cutting电弧切割grind off 磨掉metallic luster 金属光泽Screwed Piping Joints螺丝状的管接头gouging .刨削槽成形不良用语a berration 色差atomization ?化bank mark ?料纹bite 咬入blacking hole 涂料孔(铸疵) blacking scab 涂料疤blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑resin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮摺叠straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱摺surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌weld mark 焊痕whitening 白化wrinkle 皱纹模具常用刀具与工作法用语adjustable spanner 活动扳手angle cutter 角铣刀anvil 铁? arbour 心轴backing 衬垫belt sander 带式打磨机buffing 抛光chamfering machine 倒角机chamfering tool 去角刀具chisel 扁錾chuck 夹具compass 两角规concave cutter 凹面铣刀convex cutter 凸形铣刀cross joint 十字接头cutting edge clearance 刃口余隙角drill stand 钻台edge file 刃用锉刀file 锉刀flange joint 凸缘接头grinder 砂轮机hammer 铁锤hand brace 手摇钻hatching 剖面线hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽index head 分度头jack 千斤顶jig 治具kit 工具箱lapping 研磨metal saw 金工锯nose angle 刀角pinchers 钳子pliers 铗钳plug 柱塞头polisher 磨光器protable driller 手提钻孔机punch 冲头sand paper 砂纸scraper 刮刀screw driver 螺丝起子scribing 划线second out file 中纹锉spanner 扳手spline broach 方栓槽拉刀square 直角尺square sleeker 方形镘刀square trowel 直角度stripping 剥离工具T-slot T形槽tool for lathe 车刀tool point angle 刀刃角tool post 刀架tosecan 划线盘trimming 去毛边waffle die flattening 压纹效平wiper 脱模钳wrench 螺旋扳手电脑关联用语3D modeling 三次元模拟access 通路animation 卡通影片application 应用board 基板bug 故障bus 汇流排CAD 电脑辅助设计CAE 电脑辅助工程分析CAM 电脑辅助制造cassette 卡座color display 彩色显示器command 指令communication 通信compact 精简小型computer 电脑copy 复制cursor 游标curve modeling 曲面模拟database 资料库design 设计digitizing 数位化disk 磁碟dot 点eyelet 眼孔floppy 磁碟片format 格式化graphic 圆解hardware 硬体honeycomb 蜂巢interface 界面know how 秘诀laser printer 雷射印表机lay out 布置memory 记忆memory swap 交换记忆microprocessor 微处理器modeling 造型module 模组monitor 萤幕mouse 滑鼠need 需求network 网路new version 新版on line 上线中option 选择PC 个人电脑plotter 绘图机program 程式scanning 扫描simulation 模拟software 软体solid model 实体模型system 系统tape 磁带terminal 终端机texture 构造trim 修边venter 排气风扇word processor 文书处理器各种冲模加工关连用语barreling 滚光加工belling 压凸加工bending 弯曲加工blanking 下料加工bulging 撑压加工burring 冲缘加工cam die bending 凸轮弯曲加工caulking ?合加工coining 压印加工compressing 压缩加工compression bending 押弯曲加工crowning 凸面加工curl bending 卷边弯曲加工curling 卷曲加工cutting 切削加工dinking 切断蕊骨double shearing 叠板裁断drawing 引伸加工drawing with ironing 抽引光滑加工embossing 浮花压制加工extrusion 挤制加工filing 锉削加工fine blanking 精密下料加工finish blanking 光制下料加工finishing 精整加工flanging 凸缘加工folding 折边弯曲加工folding 摺叠加工forming 成形加工impact extrusion 冲击挤压加工indenting 压痕加工ironing 引缩加工knurling 滚花lock seaming 固定接合louvering 百叶窗板加工marking 刻印加工necking 颈缩加工notching 冲口加工parting 分断加工piercing 冲孔加工progressive bending 连续弯曲加工progressive blanking 连续下料加工progressive drawing 连续引伸加工progressive forming 连续成形加工reaming 铰孔加工restriking 二次精冲加工riveting ?接加工roll bending 滚筒弯曲加工roll finishing 滚压加工rolling 压延加工roughing 粗加工scrapless machining 无废料加工seaming 折弯重叠加工shaving 缺口修整加工shearing 切断加工sizing 精压加工/矫正加工slitting 割缝加工spinning 卷边?接staking ?固stamping 锻压加工swaging 挤锻压加工trimming 整缘加工upsetting 锻粗加工wiring 抽线加工冲压机械及周边关连用语back shaft 支撑轴blank determination 胚料展开bottom slide press 下传动式压力机board drop hammer 板落锤brake 煞车buckle 剥砂面camlachie cramp 铸包casting on flat ?合chamotte sand 烧磨砂charging hopper 加料漏斗clearance 间隙closed-die forging 合模锻造clump 夹紧clutch 离合器clutch brake 离合器制动器clutch boss 离合器轮壳clutch lining 离合器覆盖coil car 带卷升降运输机coil cradle 卷材进料装置coil reel stand 钢材卷料架column 圆柱connection screw 连杆调节螺钉core compound 砂心黏结剂counter blow hammer 对击锻锤cradle 送料架crank 曲柄轴crankless 无曲柄式cross crank 横向曲轴cushion 缓冲depression 外缩凹孔dial feed 分度送料die approach 模口角度die assembly 合模die cushion 模具缓冲垫die height 冲压闭合高度die life 模具寿命die opening 母模逃孔die spotting press 调整冲模用压力机double crank press 双曲柄轴冲床draght angle 逃料倾斜角edging 边锻伸embedded core 加装砂心feed length 送料长度feed level 送料高度filling core 埋入砂心filling in 填砂film play 液面花纹fine blanking press 精密下料冲床forging roll 辊锻机finishing slag 炼後熔渣fly wheel 飞轮fly wheel brake 飞轮制动器foot press 脚踏冲床formboard 进模口板frame 床身机架friction 摩擦friction brake 摩擦煞车gap shear 凹口剪床gear 齿轮gib 滑块引导部gripper 夹具gripper feed 夹持进料gripper feeder 夹紧传送装置hammer 槌机hand press 手动冲床hand rack pinion press 手动齿轮齿条式冲床hand screw press 手动螺旋式冲床hopper feed 料斗送料idle stage 空站inching 微调尺寸isothermal forging 恒温锻造key clutch 键槽离合器knockout 脱模装置knuckle mechanic 转向机构land 模具直线刀面部level 水平loader 供料器unloader 卸料机loop controller 闭回路控制器lower die 下模micro inching device 微寸动装置microinching equipment 微动装置motor 马达moving bolster 活动工作台notching press 冲缺口压力机opening 排料逃孔overload protection device 防超载装置pinch roll 导正滚轮pinion 小齿轮pitch 节距pressfit 压入progressive 连续送料pusher feed 推杆式送料pusher feeder 料片押片装置quick die change system 快速换模系统regrinding 再次研磨releasing 松释动作reversed blanking 反转下料robot 机器人roll forming machine 辊轧成形roll forming machine 辊轧成形机roll release 脱辊roller feed 辊式送料roller leveler 辊式矫直机rotary bender 卷弯成形机safety guard 安全保护装置scrap cutter 废料切刀scrap press 废料冲床seamless forging 无缝锻造separate 分离shave 崩砂shear angle 剪角sheet loader 薄板装料机shot 单行程工作shrinkage fit 收缩配合shut height 闭合高度sieve mesh 筛孔sintering of sand 铸砂烧贴slide balancer 滑动平衡器slug hole 逃料孔spin forming machine 旋压成形机spotting 合模stack feeder 堆叠拨送料机stickness 黏模性straight side frame 冲床侧板stretcher leveler 拉伸矫直机strip feeder 料材送料装置stripping pressure 弹出压力stroke 冲程take out device 取料装置toggle press 肘杆式压力机transfer 传送transfer feed 连续自动送料装置turrent punch press 转塔冲床two speed clutch 双速离合器uncoiler 闭卷送料机unloader 卸载机vibration feeder 振动送料机wiring press 嵌线卷边机线切割放电加工关连用语abnormal glow 不规则辉光放电arc discharge 电弧放电belt 皮带centreless 无心chrome bronze 铭铜clearance angle 後角corner shear drop 直角压陷deflection 桡曲度discharge energy 放电能量dressing 修整dwell 保压flange 凸缘gap 间隙graphite 石墨graphite contraction allowance 电极缩小余量graphite holder 电极夹座hair crack 发裂horn 电极臂jump 跳刀magnetic base 磁性座master graphite 标准电极pipe graphite 管状电极pulse 脉冲rib working 肋部加工roller electrode 滚轮式电极rotary surface 旋转面shank 柄部sharp edge 锐角部tough bronze 韧铜traverse 摇臂tungsten bronze ?青铜waviness 波形起伏work 工件working allowance 加工余量working dischard 加工废料。

组装、冲压、喷漆等专业词汇Assembly line 组装线Layout 布置图Conveyer 流水线物料板Rivet table 拉钉机Rivet gun 拉钉枪Screw driver 起子Electric screw driver 电动起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查fit together 组装在一起fasten 锁紧(螺丝)fixture 夹具(治具) pallet 栈板barcode 条码barcode scanner 条码扫描器fuse together 熔合fuse machine 热熔机repair 修理operator 作业员QC 品管supervisor 课长ME 制造工程师MT 制造生技cosmetic inspect 外观检查inner parts inspect 内部检查thumb screw 大头螺丝lbs. inch 镑、英寸EMI gasket 导电条front plate 前板rear plate 后板chassis 基座bezel panel 面板power button 电源按键reset button 重置键Hi-pot test of SPS 高源高压测试Voltage switch of SPS电源电压接拉键sheet metal parts 冲件plastic parts 塑胶件SOP 制造作业程序material check list 物料检查表work cell 工作间trolley 台车carton 纸箱sub-line 支线left fork 叉车personnel resource department人力资源部production department 生产部门planning department 企划部QC Section 品管科stamping factory 冲压厂painting factory 烤漆厂molding factory 成型厂common equipment 常用设备uncoiler and straightener 整平机punching machine 冲床robot 机械手hydraulic machine 油压机lathe 车床planer ('plein);|刨床miller 铣床grinder 磨床driller 钻床linear cutting 线切割electrical sparkle 电火花welder 电焊机staker=reviting machine 铆合机position 职务president 董事长general manager 总经理special assistant manager 特助factory director 厂长department director 部长deputy manager | =vice manager 副理section supervisor 课长deputy section supervisor =vice section superisor 副课长group leader/supervisor 组长line supervisor 线长assistant manager 助理to move, to carry, to handle 搬运be put in storage 入库pack packing 包装to apply oil 擦油to file burr 锉毛刺final inspection 终检to connect material 接料to reverse material 翻料wet station 沾湿台Tiana 天那水cleaning cloth 抹布to load material 上料to unload material 卸料to return material/stock to 退料scraped |'skræpid|报废scrape ..v.刮;削deficient purchase 来料不良manufacture procedure 制程deficient manufacturing procedure 制程不良oxidation |' ksi'dein|氧化scratch 刮伤dents 压痕defective upsiding down 抽芽不良defective to staking 铆合不良embedded lump 镶块feeding is not in place 送料不到位stamping-missing 漏冲production capacity 生产力education and training 教育与训练proposal improvement 提案改善spare parts=buffer 备件forklift 叉车trailer=long vehicle 拖板车compound die 合模die locker 锁模器pressure plate=plate pinch 压板bolt 螺栓name of a department 部门名称administration/general affairs dept 总务部automatic screwdriver 电动启子thickness gauge 厚薄规gauge(or jig)治具power wire 电源线buzzle 蜂鸣器defective product label 不良标签identifying sheet list 标示单screwdriver holder 起子插座pedal 踩踏板stopper 阻挡器flow board 流水板hydraulic handjack 油压板车forklift 叉车pallet 栈板glove(s)手套glove(s) with exposed fingers 割手套thumb 大拇指forefinger 食指midfinger 中指ring finger 无名指little finger 小指band-aid 创可贴iudustrial alcohol 工业酒精alcohol container 沾湿台head of screwdriver 起子头sweeper 扫把mop 拖把vaccum cleaner 吸尘器rag 抹布garbage container 灰箕garbage can 垃圾箱garbage bag 垃圾袋chain 链条jack 升降机production line 流水线chain 链条槽magnetizer 加磁器lamp holder 灯架to mop the floor 拖地to clean the floor 扫地to clean a table 擦桌子air pipe 气管packaging tool 打包机packaging 打包missing part 漏件wrong part 错件excessive defects 过多的缺陷critical defect 极严重缺陷major defect 主要缺陷minor defect 次要缺陷not up to standard 不合规格dimension/size is a little bigger 尺寸偏大(小)cosmetic defect 外观不良slipped screwhead/slippery screw head螺丝滑头thread 滑手speckle 斑点mildewed=moldy=mouldy 发霉rust 生锈deformation 变形burr(金属)flash(塑件)毛边poor staking 铆合不良excesssive gap 间隙过大grease/oil stains 油污inclusion 杂质painting peel off 脏污shrinking/shrinkage 缩水mixed color 杂色scratch 划伤poor processing 制程不良poor incoming part 事件不良fold of pakaging belt 打包带折皱painting make-up 补漆discoloration 羿色water spots 水渍polishing/surface processing 表面处理exposed metal/bare metal 金属裸露lack of painting 烤漆不到位safety 安全quality 品质delivery deadline 交货期cost 成本engineering 工程die repair 模修enterprise plan = enterprise expansionprojects 企划QC 品管die worker 模工production, to produce 生产equipment 设备to start a press 开机stop/switch off a press 关机classification 整理regulation 整顿cleanness 清扫conservation 清洁culture 教养qualified products, up-to-gradeproducts 良品defective products, not up-to-grade products 不良品waste 废料board 看板feeder 送料机sliding rack 滑料架defective product box 不良品箱die change 换模to fix a die 装模to take apart a die 拆模to repair a die 修模packing material 包材basket 蝴蝶竺plastic basket 胶筐isolating plate baffle plate; barricade 隔板carton box 纸箱to pull and stretch 拉深to put material in place, to cut material,to input 落料to impose lines 压线to compress, compressing 压缩character die 字模to feed, feeding 送料transportation 运输(be)qualfied, up to grade 合格not up to grade, not qualified 不合格material change, stock change 材料变化feature change 特性变更evaluation 评估prepare for, make preparations for 准备parameters 参数rotating speed, revolution 转速manufacture management 制造管理abnormal handling 异常处理production unit 生产单位lots of production 生产批量steel plate 钢板roll material 卷料manufacture procedure 制程operation procedure 作业流程to revise, modify 修订to switch over to, switch---tothrow--over switching over 切换engineering, project difficulty工程瓶颈stage die 工程模automation 自动化to stake, staking, reviting 铆合add lubricating oil 加润滑油shut die 架模shut height of a die 架模高度analog-mode device 类模器die lifter 举模器argon welding 氩焊vocabulary for stamping冲压常词汇stamping, press 冲压punch press, dieing out press 冲床uncoiler & strainghtener 整平机feeder 送料机rack, shelf, stack 料架cylinder 油缸robot 机械手taker 取料机conveyer belt 输送带transmission rack 输送架top stop 上死点bottom stop 下死点one stroke 一行程inch 寸动to continue, cont.连动to grip(material)吸料location lump, locating piece, blockstop 定位块reset 复位smoothly 顺利dent 压痕scratch 刮伤deformation 变形filings 铁削to draw holes 抽孔inquiry, search for 查寻to stock, storage, in stock 库存receive 领取approval examine and verify 审核processing, to process 加工delivery, to deliver 交货to return delivenry to./to send delinery back/to retrn of goods 退货registration 登记registration card 登记卡to control 管制to put forward and hand in 提报safe stock 安全库存acceptance = receive 验收to notice 通知application form for purchase 请购单consume, consumption 消耗to fill in 填写abrasion 磨损reverse angle = chamfer 倒角character die 字模to collect, to gather 收集failure, trouble 故障statistics 统计demand and supply 需求career card 履历卡to take apart a die 卸下模具to load a die 装上模具to tight a bolt 拧紧螺栓to looser a bolt 拧松螺栓to move away a die plate 移走模板easily damaged parts 易损件standard parts 标准件breaking.(be)broken,(be)cracked 断to lubricate 润滑common vocabulary for dieengineering模具工程常用词汇die 模具figure file, chart file 图档cutting die, blanking die 冲裁模progressive die, follow (-on)die连续模compound die 复合模punched hole 冲孔panel board 镶块to cutedges=side cut=side scrap 切边to bending 折弯to pull, to stretch 拉伸Line streching, line pulling 线拉伸engraving, to engrave 刻印upsiding down edges 翻边to stake 铆合designing, to design 设计design modification 设计变化die block 模块folded block 折弯块sliding block 滑块location pin 定位销lifting pin 顶料销die plate, front board 模板padding block 垫块stepping bar 垫条upper die base 上模座lower die base 下模座upper supporting blank 上承板upper padding plate blank 上垫板spare dies 模具备品spring 弹簧bolt 螺栓document folder 文件夹file folder 资料夹to put file in order 整理资料spare tools location 手工备品仓first count 初盘人first check 初盘复棹人second count 复盘人second check 复盘复核人equipment 设备waste materials 废料work in progress product 在制品casing = containerazation 装箱quantity of physical invetory secondcount 复盘点数量quantity of customs count会计师盘,点数量the first page 第一联filed by accounting department for reference 会计部存查end-user/using unit(department) 使用单位summary of year-end physical inventory bills年终盘点截止单据汇总表bill name 单据名称This sheet and physical inventory list will be sent to accounting department本表请与盘点清册一起送会计部－department together (Those of NHK will be sent to financial(NHK 厂区送财会部)Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号plate 电镀mold 成型material for engineering mold testing工程试模材料not included in physical inventory 不列入盘点sample 样品incoming material to be inspected 进货待验description 品名steel/rolled steel 钢材material statistics sheet物料统计明细表meeting minutes 会议记录meeting type 会别distribution department 分发单位location 地点chairman 主席present members 出席人员subject 主题conclusion 结论decision items 决议事项responsible department 负责单位pre-fixed finishing date 预定完成日approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheetPCE 组装厂生产排配表model 机锺work order 工令revision 版次remark 备注production control confirmation 生产确认checked by 初审approved by 核准department 部门stock age analysis sheet库存货龄分析表on-hand inventory 现有库存available material 良品可使用obsolete material 良品已呆滞to be inspected or reworked待验或重工total 合计cause description 原因说明part number/ P/N 料号type 形态item/group/class 类别quality 品质prepared by 制表notes 说明year-end physical inventory difference analysis sheet年终盘点差异分析表physical inventory 盘点数量physical count quantity 帐面数量difference quantity 差异量cause analysis 原因分析raw materials 原料materials 物料finished product 成品semi-finished product 半成品packing materials 包材good product/accepted goods/ acceptedparts/good parts 良品defective product/non-good parts 不良品disposed goods 处理品warehouse/hub 仓库on way location 在途仓oversea location 海外仓spare parts physical inventory list 备品盘点清单spare molds location 模具备品仓skid/pallet 栈板tox machine 自铆机wire EDM 线割EDM 放电机coil stock 卷料sheet stock 片料tolerance 工差score=groove 压线cam block 滑块pilot 导正筒trim 剪外边pierce 剪内边drag form 压锻差pocket for the punch head 挂钩槽slug hole 废料孔feature die 公母模expansion dwg 展开图radius 半径shim(wedge)楔子torch-flame cut 火焰切割set screw 止付螺丝form block 折刀stop pin 定位销round pierce punch=die button 圆冲子shape punch=die insert 异形子stock locater block 定位块under cut=scrap chopper 清角active plate 活动板baffle plate 挡块cover plate 盖板male die 公模female die 母模groove punch 压线冲子air-cushion eject-rod 气垫顶杆spring-box eject-plate 弹簧箱顶板bushing block 衬套insert 入块club car 高尔夫球车capability 能力parameter 参数factor 系数phosphate 皮膜化成viscosity 涂料粘度alkalidipping 脱脂main manifold 主集流脉bezel 斜视规blanking 穿落模dejecting 顶固模demagnetization 去磁;消磁high-speed transmission 高速传递heat dissipation 热传rack 上料degrease 脱脂rinse 水洗alkaline etch 龄咬desmut 剥黑膜D.I. rinse 纯水次Chromate 铬酸处理Anodize 阳性处理seal 封孔revision 版次part number/P/N 料号good products 良品scraped products 报放心品defective products 不良品finished products 成品disposed products 处理品barcode 条码flow chart 流程表单assembly 组装stamping 冲压molding 成型spare parts=buffer 备品coordinate 座标dismantle the die 折模auxiliary fuction 辅助功能poly-line 多义线heater band 加热片thermocouple 热电偶sand blasting 喷沙grit 砂砾derusting machine 除锈机degate 打浇口dryer 烘干机induction 感应induction light 感应光response=reaction=interaction 感应ram 连杆edge finder 巡边器concave 凸convex 凹short 射料不足nick 缺口speck 污点shine 亮班splay 银纹gas mark 焦痕delamination 起鳞cold slug 冷块blush 导色gouge 沟槽;凿槽satin texture 段面咬花witness line 证示线patent 专利grit 沙砾granule=peuet=grain 细粒grit maker 抽粒机cushion 缓冲magnalium 镁铝合金magnesium 镁金metal plate 钣金lathe 车mill 锉plane 刨grind 磨drill 钻boring 镗blinster 气泡fillet 镶;嵌边through-hole form 通孔形式voller pin formality 滚针形式cam driver 铡楔shank 摸柄crank shaft 曲柄轴augular offset 角度偏差velocity 速度production tempo 生产进度现状torque 扭矩spline=the multiple keys 花键quenching 淬火tempering 回火annealing 退火carbonization 碳化alloy 合金tungsten high speed steel 钨高速的moly high speed steel 钼高速的organic solvent 有机溶剂bracket 小磁导liaison 联络单volatile 挥发性resistance 电阻ion 离子titrator 滴定仪beacon 警示灯coolant 冷却液crusher 破碎机模具工程类plain die 简易模pierce die 冲孔模forming die 成型模progressive die 连续模gang dies 复合模shearing die 剪边模riveting die 铆合模pierce 冲孔forming 成型(抽凸,冲凸)draw hole 抽孔bending 折弯trim 切边emboss 凸点dome 凸圆semi-shearing 半剪stamp mark 冲记号deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平groove 压线blanking 下料stamp letter 冲字(料号)shearing 剪断tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类extension dwg 展开图procedure dwg 工程图die structure dwg 模具结构图material 材质material thickness 料片厚度factor 系数upward 向上downward 向下press specification 冲床规格die height range 适用模高die height 闭模高度burr 毛边gap 间隙weight 重量total wt.总重量punch wt.上模重量五金零件类inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销coil spring 弹簧lifter pin 顶料销eq-height sleeves=spool 等高套筒pin 销lifter guide pin 浮升导料销guide pin 导正销wire spring 圆线弹簧outer guiding post 外导柱stop screw 止付螺丝located pin 定位销outer bush 外导套top plate 上托板（顶板）top block 上垫脚punch set 上模座punch pad 上垫板punch holder 上夹板stripper pad 脱料背板up stripper 上脱料板male die 公模(凸模)feature die 公母模female die 母模(凹模)upper plate 上模板lower plate 下模板die pad 下垫板die holder 下夹板die set 下模座bottom block 下垫脚bottom plate 下托板(底板)stripping plate 内外打(脱料板) outer stripper 外脱料板inner stripper 内脱料板lower stripper 下脱料板零件类punch 冲头insert 入块(嵌入件)deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子round punch 圆冲子special shape punch 异形冲子bending block 折刀roller 滚轴baffle plate 挡块located block 定位块supporting block for location定位支承块air cushion plate 气垫板air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子ribbon punch 压筋冲子reel-stretch punch 卷圆压平冲子guide plate 定位板sliding block 滑块sliding dowel block 滑块固定块active plate 活动板lower sliding plate 下滑块板upper holder block 上压块upper mid plate 上中间板spring box 弹簧箱spring-box eject-rod 弹簧箱顶杆spring-box eject-plate 弹簧箱顶板bushing bolck 衬套cover plate 盖板guide pad 导料块塑件&模具相关英文compre sion molding 压缩成型flash mold 溢流式模具plsitive mold 挤压式模具split mold 分割式模具cavity 型控母模core 模心公模taper 锥拔leather cloak 仿皮革shiver 饰纹flow mark 流痕welding mark 溶合痕post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板piston 活塞cylinder 汽缸套chip 细碎物handle mold 手持式模具移转成型用模具encapsulation molding 低压封装成型射出成型用模具two plate 两极式（模具）well type 蓄料井insulated runner 绝缘浇道方式hot runner 热浇道runner plat 浇道模块valve gate 阀门浇口band heater 环带状的电热器spindle 阀针spear head 刨尖头slag well 冷料井cold slag 冷料渣air vent 排气道h=0.02~0.05mm w=3.2mm L=3~5mm welding line 熔合痕eject pin 顶出针knock pin 顶出销return pin 回位销反顶针sleave 套筒stripper plate 脱料板insert core 放置入子runner stripper plate 浇道脱料板guide pin 导销eject rod (bar)（成型机）顶业捧subzero 深冷处理three plate 三极式模具runner system 浇道系统stress crack 应力电裂orientation 定向sprue gate 射料浇口，直浇口nozzle 射嘴sprue lock pin 料头钩销(拉料杆)slag well 冷料井side gate 侧浇口edge gate 侧缘浇口tab gate 搭接浇口film gate 薄膜浇口flash gate 闸门浇口slit gate 缝隙浇口fan gate 扇形浇口dish gate 因盘形浇口H=F=1/2t~1/5t T=2.5~3.5mmdiaphragm gate 隔膜浇口ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Φ0.8~1.0mmRunner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣品质人员名称类QC quality control 品质管理人员FQC final quality control 终点品质管制人员IPQC in process quality control制程中的品质管制人员OQC output quality control 最终出货品质管制人员IQC incoming quality control 进料品质管制人员TQC total quality control 全面质量管理POC passage quality control 段检人员QA quality assurance 质量保证人员OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员品质保证类FAI first article inspection 新品首件检查FAA first article assurance 首件确认TVR tool verification report 模具确认报告3B 3B 模具正式投产前确认CP capability index 能力指数CPK capability index of process 模具制程能力参数SSQA standardized supplier quality合格供应商品质评估OOBA out of box audit 开箱检查QFD quality function deployment品质机能展开FMEA failure model effectiveness analysis 失效模式分析8 disciplines 8 项回复内容FA final audit 最后一次审核CAR corrective action request 改正行动要求corrective action report 改正行动报告FQC 运作类AQL Acceptable Quality Level 运作类允收品质水准S/S Sample size 抽样检验样本大小ACC Accept 允收REE Reject 拒收CR Critical 极严重的MAJ Major 主要的MIN Minor 轻微的AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service品质/可靠度服务MIL-STD Military-Standard 军用标准S I-S IV Special I-Special IV 特殊抽样水准等级P/N Part Number 料号L/N Lot Number 特采AOD Accept On Deviation 特采UAI Use As It 首件检查报告FPIR First Piece Inspection Report百万分之一PPM Percent Per Million 批号制程统计品管专类SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计品质管制R Range 全距AR Averary Range 全距平均值UCL Upper Central Limit 管制上限LCL Lower Central Limit 管制下限MAX Maximum 最大值MIN Minimum 最小值GRR GaugeReproducibility&Repeatability 量具之再制性及重测性判断量可靠与否DIM Dimension 尺寸DIA Diameter 直径FREQ Frequency 频率N Number 样品数其它品质术语类QCC Quality Control Circle 品质圈QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结ZD Zero Defect 零缺点QI Quality Improvement 品质改善QP Quality Policy 目标方针TQM Total Quality Management全面品质管理MRB Material Reject Bill 退货单LQL Limiting Quality Level 最低品质水准RMA Return Material Audit 退料认可QAN Quality Amelionrate Notice品质改善活动ADM Absolute Dimension Measurement 全尺寸测量QT Quality Target 品质目标7QCTools 7 Quality Controll Tools品管七大手法通用之件类ECN Engineering Change Notes 工程变更通知(供应商) ECO Engineering Change Order 工程改动要求(客户) PCN Process Change Notice 工序改动通知PMP Product Management Plan 生产管制计划SIP Specification In Process 制程检验规格SOP Standard Operation Procedure制造作业规范IS Inspection Specification 成品检验规范BOM Bill Of Material 物料清单PS Package Specification 包装规范SPEC Specification 规格DWG Drawing 图面系统文件类QC Quality System 品质系统ES Engineering Standarization 工程标准CGOO China General PCE 龙华厂文件H Huston (美国)休斯敦C Compaq (美国)康伯公司C China 中国大陆A Assembly 组装(厂)S Stamping 冲压(厂)P Painting 烤漆(厂)I Intel 英特尔公司T TAIWAN 台湾IWS International Workman Standard 工艺标准ISO International Standard Organization 国际标准化组织GS General Specification 一般规格CMCS C-China M-Manufacture C-Compaq S-Stamping Compaq 产品在龙华冲压厂制造作业规范CQCA Q-Quality A-AssemblyCompaq 产品在龙华组装厂品管作业规范CQCP P-Painting Company 产品在龙华烤漆厂品管作业规范部类PMC Production & Material Control 生产和物料控制PPC Production Plan Control 生产计划控制MC Material Control 物料控制ME Manafacture Engineering 制造工程部PE Project Engineering 产品工程部A/C Accountant Dept 会计部P/A Personal & Administration 人事行政部DC Document Center 资料中心QE Quality Engineering 品质工程(部)QA Quality Assurance 品质保证(处)QC Quality Control 品质管制(课)PD Product Department 生产部LAB Labratry 实验室IE Industrial Engineering 工业工程R&D Research & Design 设计开发部P Painting 烤漆(厂)A Asssembly 组装(厂)S Stamping 冲压(厂)生产类PCS Pieces 个(根,块等)PRS Pairs 双(对等)CTN Carton 卡通箱PAL Pallet/skid 栈板PO Purchasing Order 采购订单MO Manufacture Order 生产单D/C Date Code 生产日期码ID/C Identification Code (供应商)识别码SWR Special Work Request 特殊工作需求L/N Lot Number 批号P/N Part Number 料号其它OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure个人电脑外设PC Personal Computer 个人电脑CPU Central Processing Unit 中央处理器SECC SECC` 电解片SGCC SGCC 热浸镀锌材料NHK North of Hongkong 中国大陆PRC People's Republic of China中国大陆U.S.A the United States of America美国A.S.A.P As Soon As Possible 尽可能快的E-MAIL Electrical-Mail 电子邮件N/A Not Applicable 不适用QTY Quantity 数量VS 以及REV Revision 版本JIT Just In Time 零库存I/O Input/Output 输入/输出OK Ok 好NG Not Good 不行,不合格C=0 Critical=0 极严重不允许ESD Electry-static Discharge 静电排放5S 希腊语整理,整顿,清扫,清洁,教养ATIN Attention 知会CC Carbon Copy 副本复印相关人员APP Approve 核准,认可,承认CHK Check 确认AM Ante Meridian 上午PM Post Meridian 下午CD Compact Disk 光碟CD-ROM Compact Disk Read-OnlyMemory 只读光碟FDD Floppy Disk Drive 软碟机HDD Hard Disk Drive 碟碟机REF Reference 仅供参考CONN Connector 连接器CAV Cavity 模穴CAD Computer Aid Design 计算机辅助设计ASS'Y Assembly 装配,组装MAT'S Material 材料IC Integrated Circuit 集成电路T/P True Position 真位度TYP Type 类型WDR Weekly Delivery Requitement周出货需求C?T Cycle Time 制程周期L/T Lead Time 前置时间(生产前准备时间)S/T Standard Time 标准时间P/M Product Market 产品市场3C Computer,Commumcation,Consumer electronic 消费性电子5WIHWhen,Where,Who,What,Why,How to5MMan,Machine,Material,Method,Measurement4MIHMan,Materia,Money,Method,Time人力,物力,财务,技术,时间(资源)SQA Strategy Quality Assurance策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证SSQA Sales and service Quality Assurance 销售及服务品质保证LRR Lot Rejeet Rate 批退率BS Brain storming 脑力激荡EMI Electronic Magnetion Inspect高磁测试FMI Frequency Modulatim Inspect高频测试B/M Boar/Molding(flat cable)C/P Connector of PCA/P AssemblySPS Switching power supply 电源箱DT Desk Top 卧式(机箱)MT Mini-Tower 立式(机箱)DVD Digital Vedio DiskVCD Vdeio Compact DiskLCD Liquid Crystal DisplayCAD Computer AID DesignCAM Computer AID ManufacturingCAE Computer AID EngineeringABIOS Achanced Basic input/output system 先进的基本输入/输出系统CMOS Complemeruary MetollOxide Semiconductor 互补金属氧化物半导体PDA Personal Digital Assistant 个人数字助理IC Integrated Circuit 集成电路ISA Industry Standard Architecture工业标准体制结构MCA Micro Channel Architecture微通道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构SIMM Single in-line memory module 单项导通汇流组件DIMM Dual in-line Memory Module双项导通汇流组件LED Light-Emitting Diode 发光二级管FMEA Failure Mode Effectivenes失效模式分析W/H Wire Harness 金属线绪束集组件F/C Flat Calle 排线PCB Printed Circuit Board 印刷电路板CAR Correction Action Report 改善报告NG Not Good 不良WPR Weekly Delivery Requirement周出货要求PPM Parts Per Million 百万分之一TPM Total Production Maintenance全面生产保养MRP Material Requiremcnt Planning物料需计划OC Operation System 作业系统TBA To Be Design 待定,定缺D/C Drawing ChangeP/P Plans & ProceduneEMI Electrical-Music Industry 电子音乐工业RFI Read Frequency Input 读频输入MMC Maximum Material ConditionMMS Maximum Material SizeLMC Least Material ConditionLMS Least Material Size模具技术用语各种模具常用成形方式accurate die casting 精密压铸powder forming 粉末成形calendaring molding 压延成形powder metal forging 粉末锻造cold chamber die casting 冷式压铸precision forging 精密锻造cold forging 冷锻press forging 冲锻compacting molding 粉末压出成形rocking die forging 摇动锻造compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形dip mold 浸渍成形rubber molding橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造extrusion molding 挤出成形shellcasting 壳模铸造foam forming 泡成形sinter forging烧结锻造forging roll 轧锻six sides forging 六面锻造gravity casting 重力铸造Slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造hot chamber die casting 热室压铸swaging 挤锻hot forging 热锻transfer molding 转送成形injection molding 射出成形Warm forging 温锻investment casting 精密铸造matched die method 对模成形法laminating method 被覆淋膜成形low pressure casting 低压铸造lost wax casting 脱蜡铸造matchedmould thermal forming 对模热成形模各式模具分类用语bismuth mold 铋铸模landed plungermold 有肩柱塞式模具burnishing die 挤光模landed positive mold 有肩全压式模具button die 镶入式圆形凹模loadingshoe mold 料套式模具center-gated mold 中心浇口式模具loose detail mold 活零件模具chill mold 冷硬用铸模loose mold活动式模具clod hobbing 冷挤压制模louveringdie 百叶窗冲切模composite dies 复合模具manifolddie 分歧管模具counter punch 反凸模modular mold组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具electroformed mold 电铸成形模multi-gate mold 复式浇口模具expander die 扩径模offswt bendingdie 双折冷弯模具extrusion die 挤出模palletizing die叠层模family mold 反套制品模具plastermold 石膏模blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具fantail die 扇尾形模具pressure die压紧模fishtail die 鱼尾形模具profile die轮廓模flash mold 溢料式模具Progressive die 顺序模gypsum mold 石膏铸模Portable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模punching die 落料模lancing die 切口模raising(embossing)压花起伏成形re-entrant mold 倒角式模具Sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具segment mold 组合模semi-positive mold 半全压式模具shaper 定型模套single cavity mold单腔模具solid forging die 整体锻模Split forging die 拼合锻模split mold 双并式模具Spineless mold 无注道残料模具squeezing die 挤压模stretch form die拉伸成形模sweeping mold 平刮铸模swing die振动模具three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold通用模具unscrewing mold 退扣式模具yoke type die 轭型模模具厂常用之标准零配件air vent vale 通气阀anchor pin 锚梢angular pin 角梢baffle 调节阻板angular pin 倾斜梢baffle plate 折流档板ball button 球塞套ball plunger 定位球塞ball slider 球塞滑块binder plate 压板blank holder 防皱压板blanking die落料冲头bolster 上下模板bottom board 浇注底板bolster 垫板bottom plate 下固定板bracket 托架bumper block 缓冲块buster 堵口casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁) cavity retainer plate模穴托板centerpin 中心梢clamping block 锁定块coil spring螺旋弹簧cold punched nut 冷冲螺母Cooling spiral 螺旋冷却栓core 心型core pin 心型梢cotter 开口梢cross 十字接头cushion pin 缓冲梢diaphragm gate盘形浇口die approach 模头料道die bed 型底die block 块形模体die body 铸模座die bush 合模衬套die button 冲模母模die clamper 夹模器die fastener 模具固定用零件die holder 母模固定板die lip 模唇die plate 冲模板die set 冲压模座direct gate 直接浇口dog chuck 爪牙,夹头dowel 定位梢dowel hole 导套孔dowel pin 合模梢dozzle 辅助浇口dowel pin 定位梢draft 拔模锥度draw bead 张力调整杆drive bearing传动轴承ejection pad 顶出衬垫ejector 脱模器ejector guide pin 顶出导梢Ejector leader busher 顶出导梢衬套ejector pad 顶出垫ejector pin 顶出梢ejector plate 顶出板ejector rod 顶出杆ejector sleeve 顶出衬套ejector valve顶出阀eye bolt 环首螺栓filling core 椿入蕊film gate 薄膜形浇口finger pin 指形梢finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘?flash gate 毛边形浇口flask 上箱floating punch 浮动冲头gate 浇口gate land 浇口面gib 凹形拉紧goose neck 鹅颈管guide bushing 引导衬套guide pin 导梢guide post 引导柱guide plate 导板guide rail 导轨head punch 顶部冲头headless punch直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram压射柱塞inlay busher 嵌入衬套inner plunger内柱塞inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢king pin bush 主梢衬套knockout bar脱模杵land 合模平坦面land area 合模面leader busher 导梢衬套lifting pin 起模顶lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢Locating ring 定位环lock block 压块locking block 定位块locking plate 定位板loose bush 活动衬套making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate分型板mold base 塑胶模mold clamp 铸模紧固夹mold platen 模用板moving bolster换模保持装置moving bolster plate 可动侧模板One piece casting 整体铸件parallel block 平行垫块paring line分模线parting lock set 合模定位器Pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导?pin gate 针尖浇口plate 衬板pre extrusion punch 顶挤冲头punch冲头puncher 推杆pusher pin 衬套梢rack 机架rapping rod 起模杆re-entrant mold 凹入模retainer pin嵌件梢retainer plate 托料板return pin 回位梢riding stripper 浮动脱模器ring gate环型浇口roller 滚筒runner 流道runner ejector set流道顶出器Runner lock pin 流道拉梢screw plug 头塞set screw 固定螺丝shedder 脱模装置shim 分隔片。

机械行业专业术语机械工程是一个广泛的领域，注重创新和突破技术的应用和发展。

作为一个机械工程师，许多专业术语对于他的工作至关重要。

这篇文章将介绍一些机械工程中常用的专业术语，分为以下几个方面。

1.材料机械工程师必须了解各种不同种类的材料并且熟练掌握它们的性质和合适的用途。

以下是一些材料方面的专业术语：(1)强度：材料抵抗断裂的能力。

(2)韧性：材料在受到冲击或变形时能够恢复其形状的能力。

(3)硬度：材料抵抗划痕的能力。

(4)延展性：材料在受到重复冲击时能够保持形状的能力。

(5)塑性：材料的可塑性非常高，可以被拉成线。

(6)弹性：材料能够在受力之后恢复其原始形状的能力。

2.机械部件在机械行业中，机械部件往往是机械工程师工作的核心。

以下是一些机械部件方面的专业术语：(1)齿轮：齿轮是一种旋转的设备，可以通过齿轮将能量传递到其他部分。

(2)轴承：轴承是机械设备中通常使用的部件，它可以使设备旋转无摩擦或内摩擦，以减少能量损失。

(3)离合器：离合器是一个能够使两个旋转部件协同工作的装置。

(4)制动器：制动器可以将能量转换成热能以便于设备的停止。

(5)滑动块：滑动块可以通过移动，改变设备行进方向或重定位。

3.机械工具机械工具是机械工程师日常工作的重要组成部分。

以下是一些机械工具方面的专业术语：(1)钻头：钻头是一种用于锐化或切割材料的机械刀具。

(2)螺纹刀：螺纹刀可以切割出螺纹形状的振动，常常用于连接两个部件或调整设备。

(3)切割器：切割器可以快速有效地切割各种材料。

(4)扳手：扳手可以用来旋转或拧紧各种螺钉和螺栓。

(5)鎚子：鎚子可以用于敲打和锤击。

4.设备和工具机械工程师在日常工作中使用各种不同设备和工具。

以下是一些相关专业术语：(1)数控机床：数控机床是一种可以通过计算机程序控制的机器，用于在金属、塑料、塑料和石材上进行切割和模具制作。

(2)激光切割机：激光切割机是一种激光束切割设备，用于切割和现场整形。