CAN CSA Z245.20-M92
- 格式:doc
- 大小:150.00 KB
- 文档页数:34
National Standard Of Canada CAN/CSA-Z245.20-M92 External Fusion Bond Epoxy Coating for Steel Pipe
Prepared by
Canadian Standards Association
Approved by
Standards Council of Canada
ISSN 0317-5669
Published in March 1992 by Canadian Standards Association 178 Rexdale Boulevard, Rexdale (Toronto), Ontario, Canada M9W 1R3
CAN/CSA-Z245.20-M92
External Fusion Bond Epoxy
Coating for Steel Pipe
1. Scope
1.1
This Standard deals with the qualification, application, inspection, testing, handling, and storage of materials required for plant-applied fusion bond epoxy coating applied externally to bare steel pipe. The coated pipe is primarily intended for buried of submerged service for oil or gas pipeline systems.
Note: it is not intended that the application of this Standard should prevent the development of new materials, equipment, or practices, nor is it intended to prescribe specifically how such innovations should be handled.
2. Reference Publications
2.1
Where reference is made to other publications, such references shall be considered to refer to the latest edition and any revisions thereto approved by the organization issuing that publication. The year dates shown below indicate the latest issues available at the time of printing. Some reference publications are supplemented or qualified, or both. By specific requirements elsewhere in this Standard; reference publications should therefore be applied only in the context of this standard. CSA Standards
CAN/CSA-Q9001-91,
(Adoption of ISO 9001-1987 with supplementary Requirements)
Quality Systems-Quality Assurance in Design/Development, Production, Installation, and Servicing;
CAN/CSA-Q9002-91
(Adoption of ISO 9002-1987 with supplementary Requirements)
Quality Systems-Quality Assurance in production and installation;
CAN/CSA-09003-91
(Adoption of ISO 9003-1987 with Supplementary Requirements)
Quality Systems-Quality Assurance in Final Inspection and Test;
CAN3-Z299.0-M86 (R1991)
Guide for Selecting and Implementing the CAN3-Z299-85 Quality Assurance program Standards; CAN3-Z299.1-85 (R1991)
Quality Assurance program-Category 1;
CAN3-Z299.2-85 (R1991)
Quality Assurance program-Category 2;
CAN3-Z299.3-85 (R1991)
Quality Assurance program-Category 3;
CAN3-Z299.4-85 (R1991)
Quality Assurance program-Category 4;
API* Specification
Q1-1990
Spec Q1, Specification for Quality Programs.
ASTM +Standard practice
E29-89
Using Significant Digits in Test Data to Determine Conformance with Specifications.
ISO+ Standards
9000-1987,
Quality management and quality assurance standards-Guidelines for selection and use;
9001-1987,
Quality systems-Model for quality assurance in design/development, production, installation and servicing;
9002-1987
Quality systems-Model for quality assurance in production and installation;
9003-1987
Quality systems-Model for quality assurance in final inspection and test.
SIS § Standard
05 59 00-1988
Pictorial Surface Preparation Standards for Painting Steel Surfaces.
SSPC** specifications
SP 5-1989
White Metal Blast Cleaning
SP 10-1989,
Near - White Blast Cleaning;
*American petroleum institute.
+American Society for Testing and Materials.
International Organization for standardization.
Swedish Standards Institute.
**Steel Structures Painting Coundl.
3.Definitions
3.1
The following definitions apply in this Standard.
Applicator - the company responsible for the actual application of the coating.
Batch - the quantity of epoxy powder produced during a continuous production run of not more than 8 h.
Coating - fusion bond epoxy coating.
Epoxy powder - a thermosetting coating material based on epoxy resin.
Holiday - a discontinuity that exhibits electrical conductivity when exposed to a specific voltage.