# 配置 AC 与 Switch 相连的接口 GigabitEthernet1/0/1 的链路类型为 Trunk 类型，当前 Trunk 口的 PVID 为 100，禁止 VLAN1 通过，允许 VLAN 100 和 CLient 使用的 VLAN 200 通过。
[AC] interface gigabitethernet 1/0/1 [AC-GigabitEthernet1/0/1] port link-type trunk [AC-GigabitEthernet1/0/1] port trunk pvid vlan 100 [AC-GigabitEthernet1/0/1] undo port trunk permit vlan 1 [AC-GigabitEthernet1/0/1] port trunk permit vlan 100 200 [AC-GigabitEthernet1/0/1] quit
Unicast Stream
Source
Vlan-int100 160.100.54.33/16
Vlan-int200 DHCP Serve1r60.200.54.33/16 L2 switch
AC
Client 1 MAC：0007-c131-0530
Client 2
AP
MAC：0007-c131-1334
# 进入 AP 的 radio 射频视图，将服务模板绑定到 radio，并开启 radio。
[AC-wlan-ap-officeap1] radio 2 [AC-wlan-ap-officeap1-radio-2] channel 11 [AC-wlan-ap-officeap1-radio-2] service-template 1 [AC-wlan-ap-officeap1-radio-2] radio enable
组播优化功能典型配置举例
Copyright © 2014 杭州华三通信技术有限公司 版权所有，保留一切权利。 非经本公司书面许可，任何单位和个人不得擅自摘抄、复制本文档内容的部分或全部， 并不得以任何形式传播。本文档中的信息可能变动，恕不另行通知。
目录
1 简介 ······················································································································································ 1 2 配置前提 ··············································································································································· 1 3 配置举例 ··············································································································································· 1
3.1 组网需求 ··············································································································································· 1 3.2 配置思路 ··············································································································································· 1 3.3 配置注意事项········································································································································ 2 3.4 配置步骤 ··············································································································································· 2
3.4 配置步骤
3.4.1 AC的配置
(1) 配置 AC 的接口 # 创建 VLAN 100 及其对应的 VLAN 接口，并为该接口配置 IP 地址。AC 将使用该接口的 IP 地址与 AP 建立 LWAPP 隧道。
<AC> system-view [AC] vlan 100 [AC-vlan100] quit [AC] interface vlan-interface 100 [AC-Vlan-interface100] ip address 160.100.54.33 16 [AC-Vlan-interface100] quit
Client 3 MAC：0007-c131-1858
3.2 配置思路
AP 通过监听客户端上报的组播报告报文和离开报文进行组播优化表项维护。为了防止组播优化表 项老化，配置一个组播查询器，使客户端不断的响应组播查询。
1ຫໍສະໝຸດ Baidu
3.3 配置注意事项
配置 AP 的序列号时请确保该序列号与 AP 唯一对应，AP 的序列号可以通过 AP 设备背面的标签获 取。
# 开启服务模板 1。
[AC-wlan-st-1] service-template enable [AC-wlan-st-1] quit
# 创建一个 AP 管理模板，其名称为 officeap1，型号名称为 WA2620E-AGN，并配置序列号。
[AC] wlan ap officeap1 model WA2620E-AGN [AC-wlan-ap-officeap1] serial-id 21023529G007C000020
3 配置举例
3.1 组网需求
如 图 1 所示，Client通过接入无线网络播放组播视频，AC作为DHCP服务器为AP和Client分配IP地 址，现要求:在AC上开启组播优化功能，将组播数据报文转换为单播数据报文发送给客户端，以提 高组播的报文速率及减少因冲突导致的丢包。 图1 组播优化组网图
Multicast Stream
3.4.1 AC的配置 ··································································································································· 2 3.4.2 Switch的配置 ····························································································································· 4 3.5 验证配置 ··············································································································································· 4 3.6 配置文件 ··············································································································································· 5 4 相关资料 ··············································································································································· 6
(2) 配置 DHCP 服务 # 开启 DHCP 服务。
[AC] dhcp enable
# 配置 DHCP 地址池 v100 为 AP 动态分配的网段为 160.100.0.0/16，网关地址为 160.100.54.33/16。
[AC] dhcp server ip-pool v100 [AC-dhcp-pool-v100] network 160.100.0.0 16 [AC-dhcp-pool-v100] gateway-list 160.100.54.33 [AC-dhcp-pool-v100] quit
# 配置 DHCP 地址池 v200 为 Client 动态分配的网段为 160.200.0.0/16，网关为 160.200.54.33/16。
[AC] dhcp server ip-pool v200 [AC-dhcp-pool-v200] network 160.200.0.0 16
2
[AC-dhcp-pool-v200] gateway-list 160.200.54.33 [AC-dhcp-pool-v200] quit
# 配置端口 WLAN-ESS1 的缺省 VLAN 设置为 VLAN 200，允许 VLAN200 的报文不带 tag 通过， 并开启端口基于 MAC 地址划分 VLAN 的功能。
[AC-WLAN-ESS1] port hybrid vlan 200 untagged [AC-WLAN-ESS1] port hybrid pvid vlan 200 [AC-WLAN-ESS1] mac-vlan enable [AC-WLAN-ESS1] quit
i
1 简介
本文档介绍无线控制器组播优化功能典型配置举例。
2 配置前提
本文档不严格与具体软、硬件版本对应，如果使用过程中与产品实际情况有差异，请参考相关产品 手册，或以设备实际情况为准。 本文档中的配置均是在实验室环境下进行的配置和验证，配置前设备的所有参数均采用出厂时的缺 省配置。如果您已经对设备进行了配置，为了保证配置效果，请确认现有配置和以下举例中的配置 不冲突。 本文档假设您已了解 WLAN 组播优化特性。
# 创建一个新的服务模板（明文模板）1，设置服务模板 1 的 SSID 为 service。
[AC] wlan service-template 1 clear [AC-wlan-st-1] ssid service
# 将 WLAN-ESS 接口与该服务模板绑定。
[AC-wlan-st-1] bind wlan-ess 1
# 创建 VLAN 200 作为 ESS 接口的缺省 VLAN 和 Client 接入的业务 VLAN。
[AC] vlan 200 [AC-vlan200] quit
# 进入 Vlan-interface200 的接口视图，配置 IP 地址为 160.200.54.33/16。
[AC] interface vlan-interface 200 [AC-Vlan-interface200] ip address 160.200.54.33 16 [AC-Vlan-interface200] quit
(3) 配置无线接入服务和 AP 模板 # 创建编号为 1 的 WLAN-ESS 接口，配置端口的链路类型为 Hybrid，并禁止 VLAN1 通过当前的 Hybrid 端口。
[AC] interface wlan-ess 1 [AC-WLAN-ESS1] port link-type hybrid [AC-WLAN-ESS1] undo port hybrid vlan 1
